LM358ADGKRG4 - Dual 700 kHz Operational Amplifier | Texas Instruments
부품 번호: LM358ADGKRG4 ✗ 단종LM358ADGKRG4 개요
An operational amplifier, or op amp, is a high-gain differential amplifier that uses negative feedback to control gain and improve linearity. The LM358 integrates two independent, internally compensated amplifier sections into one package. Within the semiconductor hierarchy, it belongs to the amplifier IC family, which is part of the broader analog and mixed-signal IC category. Its dual-channel construction can reduce board area when a design needs two amplifier functions.
Key characteristics include a 0.7 MHz gain-bandwidth value, 0.3 V/µs slew rate, and typical supply-current drain of 0.7 mA. The low 200 nA input-bias current supports higher-source-impedance sensing circuits, while the 2 mV input offset specification defines the typical baseline for dc input imbalance. These characteristics make the device suitable for general instrumentation, industrial control, sensor interfaces, and low-to-moderate-frequency analog signal paths.
The LM358 architecture is based on bipolar transistor input stages with complementary output stages. Internally compensated operation simplifies closed-loop designs because no external compensation capacitor is required for typical voltage-follower and non-inverting amplifier configurations. The amplifier can operate from a single positive supply or from positive and negative supplies, allowing common-ground signal-conditioning arrangements to share the same device.
Typical applications include transimpedance-style sensor front ends, audio preamplifier stages, active filters, comparators with suitable output interfacing, power-supply feedback networks, and industrial control interfaces. Its 0.3 V/µs slew rate is sufficient for general analog signals, while the 700 kHz bandwidth is better suited to audio, measurement, and control loops than to high-speed data acquisition.
Designers should provide input and output bypassing close to the device, maintain adequate input and output voltage headroom, and verify common-mode range, output swing, and stability with the intended feedback network. Because the LM358 is not rail-to-rail at both input and output, supply selection must account for the signal range. The 8-pin VSSOP package also requires careful escape routing and thermal assessment in dense layouts.
This page combines the LM358ADGKRG4 electrical characteristics, drop-in replacement assessment, comparison table, application guidance, and practical PCB design notes into a compact engineering reference for component selection and implementation.
드롭인 대체품: LM358ADGKRG4 — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: LM358ADGKRG4 (동일 폼 팩터 및 풋프린트) — 차이점: Amplifier Type, Input Offset Voltage, Maximum Supply Voltage.
LM358ADGKR
✅ 드롭인가격 문의
데이터시트 보기 →LM358ADGKRG4 최대 정격 & 전기적 특성
| Number of Amplifier Circuits | 2 circuits |
| Amplifier Type | General purpose |
| Gain-Bandwidth Product | 700 kHz |
| Rated Gain-Bandwidth Product | 0.7 MHz |
| Slew Rate | 0.3 V/µs |
| Input Offset Voltage | 2 mV |
| Input Bias Current | 200 nA |
| Typical Supply-Current Drain | 0.7 mA |
| Minimum Single-Supply Operating Voltage | 3 V |
| Maximum Single-Supply Operating Voltage | 26 V |
| Maximum Supply Voltage | 16 V |
| 패키지 | 8-VSSOP / 8-TSSOP / 8-MSOP |
| Package Width | 3.00 mm |
| Package Body Width | 0.118 inch |
| Packaging | Tape and reel |
| 실장 유형 | Surface mount |
LM358ADGKRG4 0.118 inch 핀 구성 가이드
LM358ADGKRG4(0.118 inch 패키지)의 핀 구성입니다. 이 아날로그 부품에는 입력, 출력, 전원 공급 핀이 있습니다. 오프셋 널, 보상, 인에이블 핀 구성은 제조사 데이터시트를 참조하십시오. 신호 컨디셔닝 및 증폭기 회로에 이상적입니다.
다음에 대한 상세 핀아웃 데이터 없음: LM358ADGKRG4.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
LM358ADGKRG4 적합 용도: 6 애플리케이션s: Industrial Sensor Signal Conditioning, Audio Preamplification and Buffering, Power-Supply Feedback and Control, Active Filtering and Feedback Networks, Battery-Powered Monitoring System, Communication Interface Buffering.
Industrial Sensor Signal Conditioning
LM358ADGKRG4 fits two-stage industrial sensor conditioning when the signal bandwidth remains below its 700 kHz gain-bandwidth product. The 200 nA input bias current reduces loading on high-impedance sensors, while the 3 V to 26 V single-supply range accommodates common industrial rails. Two channels can provide sequential gain stages or a differential-to-single-ended input stage. Designers should verify the input common-mode range against the sensor output and use the 0.3 V/µs slew rate to assess large-signal settling time.
추천
Audio Preamplification and Buffering
The LM358ADGKRG4 can provide two general-purpose stages in audio preamplifier or buffer circuits. Its 700 kHz gain-bandwidth product covers the audio band with substantial margin, and the 0.3 V/µs slew rate supports ordinary low-to-moderate level signals. One channel may amplify a microphone or line input while the other drives a subsequent stage or forms an active filter. Headroom calculations should include the input common-mode requirement and the output swing relative to the selected supply voltage.
추천
Power-Supply Feedback and Control
LM358ADGKRG4 is appropriate for error-amplifier and supervisory feedback functions around 3 V to 26 V single-supply systems. Its 0.7 mA typical supply-current drain suits low-power monitoring circuits, while two channels permit a voltage-feedback amplifier plus a current or threshold-monitoring amplifier. Compensation and loop stability must be evaluated with the power-stage transfer function, output capacitance, and compensation network, particularly when the monitored rail has wide dynamic range or a delayed response.
추천
Active Filtering and Feedback Networks
The two internally compensated channels in LM358ADGKRG4 can implement active filters, integrators, and feedback networks in instrumentation. A 700 kHz gain-bandwidth product permits useful closed-loop bandwidth for low-frequency measurement and control functions, while 2 mV input offset and 200 nA bias current should be included in dc-error analysis. Keep resistor values high enough to limit thermal noise yet low enough to prevent parasitic loading, and confirm stability with the complete source and load configuration.
추천
Battery-Powered Monitoring System
LM358ADGKRG4 can supervise a battery-derived analog system because it starts at a 3 V supply and has a 0.7 mA typical supply-current drain. One channel may buffer a battery or sensor measurement while the other compares a scaled voltage against a reference. Since the amplifier is not rail-to-rail, the sensing and output ranges must remain inside the usable common-mode and swing regions. Low-current operation should be evaluated with the actual divider impedances and the device's quiescent-current tolerance.
추천
Communication Interface Buffering
LM358ADGKRG4 can buffer or amplify slow communication-interface signals when rise times remain compatible with its 0.3 V/µs slew rate. The dual-channel arrangement may handle a receive path and a transmit-control path, although modern high-speed interfaces require substantially wider bandwidth. The 200 nA bias current can reduce errors at high source impedances, while the 2 mV offset specification must be compared with the signal resolution. Use short feedback traces and separate sensitive-signal routing from switching nodes.
추천
추천 제품 요약
엔지니어링 참조 데이터: LM358ADGKRG4 — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 |
|---|---|
| Package | 8-VSSOP / 8-TSSOP / 8-MSOP |
| Brand | Texas Instruments |
| Number of Circuits | 2 circuits |
| Amplifier Type | General purpose |
| Gain-Bandwidth Product | 700 kHz |
| Slew Rate | 0.3 V/µs |
| Input Offset Voltage | 2 mV |
| Input Bias Current | 200 nA |
| Typical Supply-Current Drain | 0.7 mA |
| Minimum Single-Supply Operating Voltage | 3 V |
| Maximum Single-Supply Operating Voltage | 26 V |
| Packaging | Tape and reel |
주요 차별점
- Two general-purpose amplifier channels in one compact package (vs LM358N)
- Low input bias current for general-purpose signal conditioning (vs LM2904)
- Single-supply operating range covers common industrial rails (vs RC4558)
설계 노트
Place the supply-bypass capacitor immediately between the LM358 power and ground pins, with the shortest possible ground return. Keep the amplifier input, feedback components, and output routing away from switching nodes and high-current traces. Because the device uses a compact 8-VSSOP footprint, verify courtyard clearance, solder-paste volume, reflow profile, and assembly inspection requirements before releasing the PCB.
Use the pin-description table and package drawing from the manufacturer datasheet before assigning PCB pads. The LM358 contains two amplifier channels, but the channel order and power-pin locations must not be inferred from generic LM358 diagrams. A board-level drop-in decision also requires matching the exact 8-VSSOP land pattern; a functional LM358 in a through-hole or different surface-mount package cannot be soldered onto the same footprint.
Do not treat the 26 V single-supply capability as permission to apply 26 V to every pin or expect rail-to-rail behavior. Check input common-mode voltage, output swing, supply sequencing, and maximum total supply voltage in the worst-case operating condition. Also confirm the intended gain and capacitive load against the 0.3 V/µs slew rate and 700 kHz gain-bandwidth product rather than relying on the nominal amplifier description alone.
Estimated: the quiescent-current contribution is 0.7 mA per LM358ADGKRG4 package at the typical condition stated in the product listing. Input 3.3 V and calculate supply power as 3.3 V multiplied by 0.7 mA, which equals approximately 2.31 mW for the quiescent path. Add load current and external-network consumption when sizing the regulator and bypass capacitor. This estimate does not include temperature, supply tolerance, or worst-case current variation.
규정 준수 정보
No specific RoHS, REACH, lead-free, halogen-free, or conflict-minerals declaration was identified for the exact ordering code. AEC-Q100 is not applicable to this general-purpose dual operational amplifier.