LM393BIDSGR - 38V Dual Open-Collector Comparator | TI
MPN: LM393BIDSGR ✓ Hoạt độngLM393BIDSGR Tóm tắt
A comparator is an analog integrated circuit that compares two input voltages and changes its output state when one input crosses the other. The LM393 family belongs to the hierarchy of linear integrated circuits, voltage comparators, and general-purpose interface ICs. Its open-collector outputs can sink current from multiple downstream devices while remaining electrically isolated from the supply rail, making the device useful for wired logic, relay drivers, and open-drain bus arrangements.
The B-version LM393B improves several characteristics over the original LM393 family. Maximum supply voltage increases to 38 V, input offset voltage decreases to 0.37 mV, and input bias current decreases to 3.5 nA. The supply current is 200 µA per comparator, and dedicated ESD clamps provide a 2 kV human-body-model ESD rating with improved input ruggedness. Quiescent current remains independent of the supply voltage according to the manufacturer product page.
Each channel contains a differential input stage and an open-collector output stage. The common-mode input range and output behavior determine where the device can operate in a system, so the pin-description and electrical-characteristics tables in the Texas Instruments LM393B datasheet should be checked against the actual signal levels. Because the outputs are open collector, an external pull-up resistor is required when the output must reach a high voltage. Two pull-up resistors can also be tied together to form a wired-AND arrangement.
Typical uses include overvoltage detection, window comparison with both channels, zero-cross detection, sensor signal conditioning, and battery or power-supply supervision. The wide supply range also suits industrial control systems, while the low input bias current reduces loading on high-impedance dividers. The compact 2x2 mm WSON package supports space-constrained portable and embedded designs.
Designers should place decoupling capacitors close to the supply and ground pins, route sensitive input traces away from switching nodes, and account for the pull-up network when setting output rise times. The exposed pad and low-profile package also require attention to solder-paste layout and thermal spreading under continuous comparator activity.
This page combines the manufacturer device information with practical guidance on pin assignment, open-collector interfacing, supply bypassing, input protection, and qualified drop-in alternatives, providing engineering context beyond a basic distributor listing.
Bộ thay thế dễ dàng lắp đặt cho LM393BIDSGR — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
LM393BDSGR
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
LM2903BIDSGR
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →LM393BIDGKT
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
LM393BIDSGR Tỷ lệ tối đa & tính chất điện
| Comparator Type | Dual general-purpose voltage comparator |
| Number of Channels | 2 independent comparators |
| Maximum Supply Voltage | 38 V |
| Input Offset Voltage | 0.37 mV |
| Input Bias Current | 3.5 nA |
| Điện áp cung cấp | 200 µA per comparator |
| ESD Rating | 2 kV HBM |
| Kiểu đầu ra | Open-collector |
| Supply Type | Single supply |
| Commercial Grade | Dual commercial-grade standard comparator |
| Hộp | 8-WSON (2x2 mm) |
| Kiểu lắp đặt | Surface mount |
| Product Family | LM393B / LM2903B dual comparator family |
| Input Protection | Dedicated ESD clamps |
| Quiescent Current Behavior | Independent of supply voltage |
Cấu hình chân LM393BIDSGR
| Chân 1 | OUT1 — Comparator 1 open-collector output |
| Chân 2 | IN1- — Comparator 1 inverting input |
| Chân 3 | IN1+ — Comparator 1 non-inverting input |
| Chân 4 | GND — Ground connection |
| Chân 5 | IN2+ — Comparator 2 non-inverting input |
| Chân 6 | IN2- — Comparator 2 inverting input |
| Chân 7 | OUT2 — Comparator 2 open-collector output |
| Chân 8 | VCC — Positive supply connection |
Ứng dụng tiêu biểu
LM393BIDSGR phù hợp cho 6 Áp dụngs: Power-Supply Overvoltage Detection, Battery Threshold Monitoring, Sensor Signal Conditioning, Window Comparator for Limit Detection, Relay and Solenoid Drive Interface, Zero-Cross and Edge Detection.
Power-Supply Overvoltage Detection
The LM393BIDSGR fits overvoltage supervision because one channel can compare a divided output rail against a reference and the 38 V maximum supply rating provides margin for monitored industrial sources. Its 0.37 mV input offset and 3.5 nA input bias current limit errors from high-impedance divider networks. Use the open-collector output to pull down a system fault signal through an external pull-up, adding hysteresis around the threshold to prevent repeated switching near the trip point.
Được đề xuất
Battery Threshold Monitoring
The LM393BIDSGR can monitor a battery pack by comparing a scaled cell voltage against a precision reference on each of its two independent channels. The low 3.5 nA bias current is valuable with a high-value divider, while the 200 µA-per-comparator supply current limits the load on low-energy systems. The compact 8-WSON (2x2 mm) package also leaves room for protection components in portable battery packs and energy-storage monitoring modules.
Được đề xuất
Sensor Signal Conditioning
The LM393BIDSGR works well as a front-end threshold detector for resistive, optical, or industrial sensor signals because its 3.5 nA input bias current produces minimal loading. One channel can establish a fixed threshold while the other compares the sensor against a programmable reference. With a 38 V maximum rating and dedicated 2 kV HBM input clamps, the device is suitable for industrial sensing systems where inputs are exposed to electrically noisy environments.
Được đề xuất
Window Comparator for Limit Detection
Both channels of the LM393BIDSGR can be assigned to the upper and lower limits of a measurement window, making the device effective for undervoltage and overvoltage detection in a single package. Its 0.37 mV offset supports accurate threshold placement near mid-supply, and the two open-collector outputs can share a pull-up to create a fault signal. Add positive feedback to each channel as hysteresis and verify that the reference and input voltages remain within the specified common-mode range.
Được đề xuất
Relay and Solenoid Drive Interface
The open-collector output of the LM393BIDSGR can sink the base or gate current of an external transistor that drives a relay, solenoid, or motor stage. This keeps the comparator output separate from the load supply and avoids driving a high-voltage coil directly from the IC. Select the pull-up value from the required sink current, add a flyback diode for an inductive load, and use the comparator's common-mode range to verify that the sensing signal is valid during switching.
Được đề xuất
Zero-Cross and Edge Detection
The LM393BIDSGR can detect when a signal crosses a reference level, supporting zero-cross, phase, or edge-detection functions in motor control and signal-conditioning circuits. Its dual-channel arrangement permits one channel to handle zero-cross detection while the other monitors a separate trip condition. The open-collector output drives a pull-up network, so the pull-up value and board capacitance set the edge rate; add hysteresis or filtering when noise near the crossing point is significant.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho LM393BIDSGR — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | LM393BDSGR | LM2903BIDSGR | LM393BIDGKT |
|---|---|---|---|---|
| Package | 8-WSON (2x2 mm) | 8-WSON (2x2 mm) | 8-WSON (2x2 mm) | 8-WSON (2x2 mm) |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Comparator Type | Dual general-purpose voltage comparator | Dual general-purpose voltage comparator | Dual voltage comparator | Dual general-purpose voltage comparator |
| Maximum Supply Voltage | 38 V | 38 V | 38 V | 38 V |
| Output Type | Open-collector | Open-collector | Open-collector | Open-collector |
| Number of Channels | 2 | 2 | 2 | 2 |
Bảo phân biệt quan trọng
- B-version input accuracy supports tighter threshold detection (vsLM393BDSGR)
- Low input loading preserves high-impedance sensor signals (vsLM2903BIDSGR)
- Compact 2x2 mm package preserves board area (vsLM393BIDGKT)
Ghi chú thiết kế
Place the supply-decoupling capacitor and the two ground connections as close to the device as the 8-WSON (2x2 mm) land pattern permits. Route the non-inverting and inverting inputs as matched, short traces, and keep them away from switching-node copper. The exposed pad must be tied to the ground plane and connected with multiple thermal-vias where the PCB design rules permit, because heat from the device and both output channels is removed through that pad.
Add external pull-up resistors to both open-collector outputs unless another device on the board already provides the required pull-up network. Size the resistor for the available sink current and the required rise time; a smaller value produces a faster edge but increases low-state current. Place the pull-up resistor close to the output node when long traces are involved. The pull-up voltage must remain within the absolute maximum rating of every connected device.
Do not assume the two comparator inputs can swing across the complete supply range. Check the specified common-mode range for the operating supply, and use a resistor divider or level shift when a sensor output can exceed it. The 2 kV HBM ESD rating adds input ruggedness but does not authorize operation beyond absolute maximum conditions. Also avoid connecting an open-collector output to a supply directly without confirming that the pull-up voltage and output leakage are acceptable.
Thông tin tuân thủ
The device is a general-purpose industrial-grade comparator. A 2 kV HBM ESD rating is specified, but AEC-Q100 automotive qualification and material-compliance declarations are not established by the cited device information.