LMR324F-GE2 - 4-Channel Low-Power Op Amp | ROHM
MPN: LMR324F-GE2 ✓ Hoạt độngLMR324F-GE2 Tóm tắt
An operational amplifier, commonly called an op amp, is an active analog component that uses high gain and negative feedback to amplify the voltage difference between its two inputs. The LMR324 belongs to the low-dropout linear-amplifier hierarchy and the broader operational-amplifier semiconductor category. Its ground-sense architecture is intended for applications operating near the lower supply rail, while the full-swing output extends usable output range toward both supply limits.
The primary features include four amplifier circuits per package, rail-to-rail output, low supply-current consumption, low-voltage operation, and a general-purpose signal path. These characteristics make the device useful where several low-level signals must be amplified, buffered, or conditioned without allocating a separate package to every channel. The quad configuration can also reduce board area and simplify power distribution compared with four discrete single amplifiers.
Each channel is intended for conventional closed-loop operation with external feedback. The ground-sense input arrangement is especially relevant to portable measurement, sensor-interface, and low-voltage control circuits where signals may occupy the lower portion of the supply range. Because final offset, bandwidth, slew rate, common-mode range, and output-current limits determine practical performance, designers should consult the ROHM LMR324F datasheet before setting gain, loading, or bypassing values.
Typical uses include low-voltage sensor conditioning, portable instrumentation, industrial control interfaces, battery-powered monitoring, and general-purpose audio or control-signal amplification. A four-channel implementation can provide independent amplification for bridge sensors, analog filters, level conversions within an analog domain, or small actuator-control loops. The same package can also implement repeated circuit blocks where matching and identical part characteristics simplify design review and maintenance.
For a new design, pay particular attention to input common-mode range, output swing under load, stability with the selected feedback network, and decoupling requirements. Place supply bypass capacitors close to the device and route each ground reference carefully, especially when all four channels process signals from different sources. Confirm that the electrical limits support the intended supply voltage, source impedance, capacitive load, and ambient temperature.
This product page combines the manufacturer product information, package identification, cross-reference findings, and practical engineering guidance. It helps engineers compare the LMR324F-GE2 with its documented alternatives while focusing on fit-for-purpose decisions rather than treating package similarity alone as proof of electrical equivalence.
Bộ thay thế dễ dàng lắp đặt cho LMR324F-GE2 — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với LMR324F-GE2 (cùng hình factor và footprint) — khác nhau ở Package.
LMR324FJ-GE2
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
LMR324F-GE2 Tỷ lệ tối đa & tính chất điện
| Number of Amplifier Circuits | 4 circuits |
| Device Type | General-purpose operational amplifier |
| Architecture | Ground-sense low-power operational amplifier |
| Output Characteristic | Rail-to-rail output |
| Hộp | 14-SOP |
| Kiểu lắp đặt | Surface mount |
Hướng dẫn cấu hình chân LMR324F-GE2 14-sop
Cấu hình chân cho LMR324F-GE2 (14-sop gói). Thành phần số hiệu này có chân đầu vào, đầu ra và nguồn cung cấp. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết cấu hình chân bù, bù trừ và chân kích hoạt. Hoàn hảo cho điều kiện tín hiệu và mạch khuếch đại.
Không có dữ liệu chân cụ thể sẵn có cho LMR324F-GE2.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
LMR324F-GE2 phù hợp cho 6 Áp dụngs: Low-Voltage Sensor Signal Conditioning, Portable Battery-Powered Monitoring, Industrial Control Signal Conditioning, General-Purpose Analog Filtering, Audio Interface Conditioning, Test and Measurement Buffering.
Low-Voltage Sensor Signal Conditioning
The LMR324F-GE2 fits multi-sensor conditioning because it provides four ground-sense amplifier channels, rail-to-rail output, and low-voltage operation in one 14-SOP package. Place one channel around each resistive sensor or low-level transducer, then use external feedback to establish the required gain. The ground-sense input arrangement is useful when the measured signal lies near the lower supply rail, while the full-swing output increases the usable output range. Before finalizing the bias network, confirm that the sensor voltage and noise amplitude remain inside the datasheet common-mode range and that the selected gain is stable at the actual source impedance.
Được đề xuất
Portable Battery-Powered Monitoring
The LMR324F-GE2 is appropriate for portable monitoring when low-voltage operation and low supply-current consumption are priorities. Its four channels can process temperature, pressure, current, or resistive sensor outputs without requiring four separate amplifier packages. The 14-SOP arrangement reduces board area while centralizing the supply connection. Because battery-powered equipment may impose strict current limits, calculate the total supply demand using the manufacturer operating-current and quiescent-current limits. Also verify the maximum and minimum supply voltages during battery transitions so every input remains within the amplifier's permitted common-mode range.
Được đề xuất
Industrial Control Signal Conditioning
The LMR324F-GE2 can condition several low-level industrial control signals in one package. Use the four channels for sensor interfaces, actuator command buffers, or analog threshold stages, with each amplifier configured through its own feedback network. The ground-sense architecture is useful for control electronics whose signals are referenced close to the lower analog rail, and the rail-to-rail output provides more available signal range than a conventional non-rail-to-rail output stage. For factory equipment, verify input range, output swing, and channel-to-channel behavior against the ROHM datasheet, and use a quiet, well-decoupled supply to prevent switching or relay transients from corrupting the amplified signals.
Được đề xuất
General-Purpose Analog Filtering
The LMR324F-GE2 supports active-filter designs that require multiple amplifier channels sharing a common supply. Sallen-Key or multiple-feedback sections can be implemented across the four internal amplifiers, simplifying analog signal-conditioning boards without adding four separate packages. Low-voltage operation and low supply-current consumption help preserve portable-system power budgets. The critical design checks are loop stability, gain accuracy, and output drive into the next filter or ADC stage. Use the manufacturer's gain-bandwidth, slew-rate, and output-current limits when selecting resistor and capacitor values, and keep sensitive filter nodes away from switching nodes and high-current return paths.
Được đề xuất
Audio Interface Conditioning
The LMR324F-GE2 can provide low-level gain and buffering around audio converter inputs when the operating levels fall within its electrical limits. Its four amplifier channels may condition two stereo channels through balanced stages or provide additional monitoring and output-buffering paths. The rail-to-rail output can be valuable in a low-voltage mixed-signal design, although the complete signal chain must avoid clipping and must remain within the specified input common-mode range. Confirm noise, bandwidth, slew rate, and output-current capability for the intended audio bandwidth, and route analog returns carefully to prevent converter clocks and digital switching currents from coupling into the conditioned audio path.
Được đề xuất
Test and Measurement Buffering
The LMR324F-GE2 is useful as a general-purpose input buffer and gain stage for compact measurement equipment. Four channels can buffer separate sensor inputs before multiplexing or conversion, reducing loading on the measured sources. The ground-sense characteristic supports low-level signals referenced near ground, while the rail-to-rail output helps retain usable signal amplitude at reduced supply voltages. For instrumentation-grade accuracy, compare the datasheet offset, bias-current, noise, and drift limits with the measurement error budget. Account for input bias current when choosing source resistors and verify capacitive loading at the ADC input so the selected feedback network maintains closed-loop stability.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho LMR324F-GE2 — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | LMR324FJ-GE2 |
|---|---|---|
| Number of Amplifier Channels | 4 circuits | 4 circuits |
| Package | 14-SOP | 14-SOP |
| Brand | ROHM Semiconductor | ROHM Semiconductor |
Bảo phân biệt quan trọng
- Four channels in one package (vsLMR358F-GE2)
- Ground-sense low-power positioning (vsLM324F-GE2)
- Rail-to-rail output for compact low-voltage systems (vsLMR324FJ-GE2)
Ghi chú thiết kế
Place the supply bypass capacitor immediately adjacent to the LMR324F-GE2 supply and ground pins, and route each amplifier's feedback components close to their corresponding channel pins. Separate sensitive input and feedback traces from switching-node, relay, and high-current return paths. Because one package contains four amplifiers, sharing the package does not justify sharing a sensitive ground reference when the channels originate from different sources.
Do not assume that rail-to-rail output alone permits operation across the entire supply range. Check the input common-mode limits and output-swing curves in the ROHM manufacturer datasheet at the intended load current. Also account for input bias-current error when using high-impedance sensors, and verify capacitive loading at the amplifier output to maintain closed-loop stability.
Calculate power consumption from the selected supply voltage, total channel activity, and the datasheet supply-current limits. Four channels operating simultaneously can increase aggregate current even though each channel is designed for low-power operation. In battery systems, include quiescent current, sensor current, and downstream converter losses in the budget. Confirm startup and shutdown behavior if the amplifier remains connected while the supply ramps through an undefined voltage.
Thông tin tuân thủ
No specific RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declarations for LMR324F-GE2 were identified in the referenced product information.