LPC2129FBD64 - 60MHz ARM7 MCU with 256KB Flash | NXP
MPN: LPC2129FBD64 ✓ Hoạt độngLPC2129FBD64 Tóm tắt
An Arm7TDMI-S microcontroller combines a 32-bit ARM processor core with 16-bit Thumb instruction support. The LPC2129 family belongs to the broader hierarchy of Arm microcontrollers, embedded processors, and integrated circuits designed for real-time control. Its 128-bit memory interface and accelerator architecture support efficient 32-bit execution, while Thumb mode can reduce code footprint when memory capacity is constrained.
The 256 KB embedded high-speed flash provides dedicated program storage without an external memory device. ISP and IAP capabilities support programming and field-update workflows, while the integrated 10-bit ADC supports analog measurement and threshold-based control. CAN support is valuable for industrial networking, and boundary-scan functionality assists board-level validation. Real-time emulation and embedded trace improve debugging visibility for control-loop and communication diagnostics.
The 64-LQFP package uses a 0.5 mm terminal pitch and is designed for surface mounting. Its 10 x 10 mm body offers substantially more board area than smaller leadless packages while retaining through-board inspection visibility. The LPC2129's 60 MHz Arm7TDMI-S core is suitable for protocol processing, supervisory control, sensor interfaces, and embedded CAN nodes that do not require the software ecosystem of a newer Cortex-M MCU.
Typical applications include industrial CAN gateways, motor and machine controllers, building automation modules, data loggers, test equipment, and embedded instrumentation. The combination of on-chip flash, ADC, CAN, and debug support reduces external component count and simplifies firmware deployment where field programming and deterministic peripheral access are important.
Designers should confirm pin-level multiplexing, regulator tolerances, peripheral availability, and memory mapping against the NXP datasheet. Crystal and decoupling layouts should follow the manufacturer's reference configuration. Firmware migration should also verify startup code, bootloader behavior, and peripheral-driver compatibility because ARM7 and Cortex-M products use different exception and interrupt architectures.
This page consolidates the NXP product information, ordering variants, drop-in compatibility guidance, application guidance, and design considerations into one engineering-focused reference for selecting and implementing the LPC2129FBD64.
Bộ thay thế dễ dàng lắp đặt cho LPC2129FBD64 — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với LPC2129FBD64 (cùng hình factor và footprint) — khác nhau ở Package, Memory Interface Width, Flash Memory, Operating Temperature, Programming Support.
LPC2129FBD64/01
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
LPC2129FBD64/01,15
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
LPC2129FBD64,151
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
LPC2129FBD64-S
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
LPC2119FBD64
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →LPC2132FBD64/01151
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →LPC2129FBD64 Tỷ lệ tối đa & tính chất điện
| Product Type | 16/32-bit microcontroller |
| Processor Core | Arm7TDMI-S |
| Tần số xung maksimum | 60 MHz |
| Embedded Flash Memory | 256 KB |
| Flash Organization | 256K x 8 |
| ADC Resolution | 10 bit |
| CAN Interface | Yes |
| Programming Support | ISP and IAP |
| Debug Support | Real-time emulation and embedded trace |
| Boundary Scan | Supported |
| Memory Interface Width | 128 bit |
| Hộp | 64-LQFP, 10 x 10 mm |
| Terminal Pitch | 0.5 mm |
| Kiểu lắp đặt | Surface mount |
| Khoảng nhiệt độ hoạt động | -40°C to +85°C |
| Nominal 3.3 V Supply | 3.3 V |
| Nominal 1.8 V Supply | 1.8 V |
Hướng dẫn cấu hình chân LPC2129FBD64 64-lqfp, 10 x 10 mm
Cấu hình chân cho LPC2129FBD64 (64-lqfp, 10 x 10 mm gói). IC số này bao gồm chân GPIO, giao diện truyền thông (UART, SPI, I2C) và chân nguồn. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết các chức năng chân thay thế và tùy chọn cấu hình. Cực kỳ quan trọng cho thiết kế hệ thống tích hợp và lập trình PCB.
Không có dữ liệu chân cụ thể sẵn có cho LPC2129FBD64.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
LPC2129FBD64 phù hợp cho 6 Áp dụngs: Industrial CAN Control Node, Data Acquisition and Sensor Interface, Embedded Test and Measurement Equipment, Building Automation Module, Machine and Motor Supervisory Controller, Field-Programmable Data Logger.
Industrial CAN Control Node
The LPC2129FBD64 fits an industrial CAN control node because it combines a 60 MHz Arm7TDMI-S core with an integrated CAN controller, 256 KB of flash, and a 10-bit ADC. The processor can manage protocol handling, supervisory logic, and analog monitoring without requiring a separate external memory device. Its -40°C to +85°C operating range and 64-LQFP package suit industrial equipment that must perform field firmware updates. A CAN transceiver, protection network, and isolated or non-isolated power architecture must still be designed around the MCU, while the embedded 256 KB supports application code, diagnostics, and ISP/IAP update workflows.
Được đề xuất
Data Acquisition and Sensor Interface
The LPC2129FBD64 is suitable for data-acquisition and sensor-interface equipment that benefits from an integrated 10-bit ADC and deterministic 60 MHz processing. Engineers can sample analog channels, filter readings, apply thresholds, and expose results through CAN or other serial peripherals while retaining 256 KB of embedded program storage. The 128-bit memory interface and accelerator architecture support efficient 32-bit code execution, while Thumb mode can reduce code size in space-sensitive firmware. Because the ADC is 10-bit, accuracy calculations must include reference-voltage tolerance, input impedance, sampling time, and the analog front end required by the sensor.
Được đề xuất
Embedded Test and Measurement Equipment
The LPC2129FBD64 can serve as the control processor in embedded test and measurement equipment where real-time sequencing, calibration data, and communication must be handled in one device. Its 60 MHz Arm7TDMI-S core provides timing headroom for instrument control, while 256 KB of flash stores firmware, calibration tables, and communication routines. Real-time emulation and embedded trace support development of timing-sensitive acquisition sequences, and boundary scan assists board-level validation. The 64-LQFP footprint remains inspectable after assembly, although its 0.5 mm pitch requires adequate board-routing and inspection capabilities.
Được đề xuất
Building Automation Module
The LPC2129FBD64 is appropriate for a building-automation module that coordinates sensors, actuators, and networked equipment. Its integrated ADC can monitor analog environmental or occupancy-related signals, while CAN can connect supervisory controllers to field equipment. The 256 KB flash capacity provides room for protocol stacks, scheduling logic, diagnostics, and over-the-air update components. Operation across -40°C to +85°C supports equipment located in controlled plant rooms, while the LQFP package offers a practical compromise between compact size and solder-joint inspection. The power design should accommodate both the identified 3.3 V and 1.8 V supply rails and peripheral load requirements.
Được đề xuất
Machine and Motor Supervisory Controller
The LPC2129FBD64 can act as a supervisory controller for industrial machines or motor systems where deterministic control, status monitoring, and network communications are required. At 60 MHz, the Arm7TDMI-S core can execute control logic and communicate over CAN while the 10-bit ADC handles feedback signals within its specified accuracy limits. Embedded flash enables application code and parameter storage, and ISP/IAP supports maintenance updates. Actual motor-drive safety, current sensing, and power-stage control require separate components because the microcontroller does not directly replace a gate driver or high-power stage.
Được đề xuất
Field-Programmable Data Logger
The LPC2129FBD64 fits a field-programmable data logger that stores operating code and capture parameters in its 256 KB embedded flash and can be serviced through ISP or IAP. The integrated ADC supports periodic sensor conversion, while the 60 MHz processor leaves capacity for buffering, timestamps, event classification, and CAN-based transfer to a host. Its -40°C to +85°C range supports many industrial environments, and the LQFP package simplifies inspection and rework compared with a leadless package. Deployment planning should include flash endurance, update integrity, brownout handling, and recovery behavior for interrupted field programming.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho LPC2129FBD64 — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | LPC2129FBD64/01 | LPC2129FBD64/01,15 | LPC2119FBD64 |
|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | LQFP-64 (10 x 10 mm) | LQFP-64 (10 x 10 mm) | LQFP-64 (10 x 10 mm) | LQFP-64 (10 x 10 mm) |
| Processor Core | Arm7TDMI-S | Arm7TDMI-S | Arm7TDMI-S | Arm7TDMI-S |
| Maximum Clock Frequency | 60 MHz | 60 MHz | 60 MHz | 60 MHz |
| Embedded Flash Memory | 256 KB | 256 KB | 256 KB | 128 KB |
| ADC Resolution | 10 bit | 10 bit | 10 bit | 10 bit |
| CAN Interface | Yes | Yes | Yes | Yes |
| Programming Support | ISP and IAP | ISP and IAP | ISP and IAP | ISP and IAP |
Bảo phân biệt quan trọng
- Provides twice the flash capacity of the LPC2119FBD64 family member (vsLPC2119FBD64)
- Retains the same 60 MHz Arm7TDMI-S performance in the closest LPC2129 ordering configurations (vsLPC2129FBD64/01,15)
- Combines CAN, a 10-bit ADC, and on-chip flash in one MCU (vsLPC2132FBD64/01)
- Supports a compact 64-LQFP footprint with inspectable leads (vsLPC2129FBD64/01)
Ghi chú thiết kế
Plan the power tree around the device's identified 1.8 V and 3.3 V operating rails, including the exact core, I/O, analog, and peripheral supply requirements in the manufacturer datasheet. Place the required bypass capacitors at their designated supply pins with short ground returns, and separate sensitive analog routing from switching-node and high-current return paths. Validate startup sequencing, brownout behavior, and regulator headroom across the full temperature range before releasing a production design.
Use the manufacturer reference layout for the 64-LQFP footprint, including the 10 x 10 mm body, 0.5 mm pitch, pad dimensions, and exposed thermal strategy if specified. Confirm land geometry against the current package drawing rather than scaling a generic LQFP footprint. Preserve access to the debug, reset, clock, and programming signals, and place decoupling close to the corresponding pins. Adequate copper and thermal-via coverage improve heat transfer from the 60 MHz processing device.
Do not assume that equal package dimensions guarantee firmware compatibility across LPC21xx devices. Verify startup configuration, memory sizes, interrupt vectors, peripheral availability, pin multiplexing, and device identifiers before substituting LPC2119FBD64 or LPC2132FBD64/01. For exact LPC2129 order-code variants, confirm the suffix meaning, qualification status, and intended operating conditions in the ordering table. Use the Request a Quote form to confirm the exact production MPN before placing an order.
Treat clock, reset, debug-trace, and high-speed memory signals as potentially timing-sensitive even though the device operates from a comparatively moderate 60 MHz. Follow the NXP recommended crystal, oscillator, reset, and debug-circuit arrangements, and keep clock routing short and away from CAN, ADC, and switching-supply paths. For CAN communication, keep the transceiver placement close to the connector, provide the required protection and return path, and follow the transceiver layout guidance to limit radiated emissions and susceptibility.
Thông tin tuân thủ
The product information identifies the device as an industrial-temperature microcontroller but does not provide definitive RoHS, REACH, lead-free, halogen-free, or conflict-minerals declarations. AEC-Q100 status is not applicable to the base industrial part designation.