LT8645SEV#PBF - 65V 8A Silent Switcher Buck Regulator | Analog Devices
MPN: LT8645SEV#PBF ✓ Hoạt độngLT8645SEV#PBF Tóm tắt
A buck (step-down) DC-DC switching regulator converts a higher DC input voltage to a lower DC output voltage by rapidly switching an internal power MOSFET pair and smoothing the resulting chopped waveform with an LC output filter. The LT8645SEV belongs to the broader category hierarchy of synchronous buck regulator -> step-down converter -> DC-DC converter -> power management IC -> semiconductor. The Silent Switcher architecture in this part integrates internal bypass capacitors and uses optimized internal layout to minimize hot-loop parasitic inductance, dramatically reducing EMI compared to conventional buck converters.
Key features include 8 A continuous output current, a peak efficiency greater than 95%, ultra-low quiescent current suitable for battery-powered applications, and internal top and bottom N-channel MOSFET switches. The regulator supports 200 kHz to 2.2 MHz switching frequency operation, allowing trade-offs between efficiency and external component size. The exposed pad package provides a low thermal resistance path, critical for high-current operation.
Typical applications include automotive always-on systems, industrial 48 V bus point-of-load conversion, distributed power systems, and battery-powered portable equipment where low EMI is required. The wide input voltage range supports harsh automotive cold-crank and load-dump transients.
When designing with this device, follow the datasheet reference layout exactly to preserve Silent Switcher performance. Use low-ESR ceramic input and output capacitors placed close to the IC, and route the BST and INTVCC capacitors with short, wide traces. The exposed pad must be soldered to a sufficiently large copper area for thermal dissipation.
This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.
Bộ thay thế dễ dàng lắp đặt cho LT8645SEV#PBF — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với LT8645SEV#PBF (cùng hình factor và footprint) — khác nhau ở Package, Architecture, Operating Temperature Range, Switching Frequency, Input Voltage Range.
LT8645SEV-2#PBF
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
LT8646SEV#PBF
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
LT8645SIV#PBF
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →LT8645SJV#PBF
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
LT8645SIV#WPBF
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
LT8645SEV#PBF Tỷ lệ tối đa & tính chất điện
| Cấu trúc | Synchronous Buck (Step-Down) |
| Phạm vi điện áp đầu vào | 3.4 V to 65 V |
| Khoảng điện áp đầu ra | 0.97 V to 25 V (adjustable) |
| Điện áp tối đa đầu ra | 8 A |
| Số lượng đầu ra | 1 |
| Switching Frequency Range | 200 kHz to 2.2 MHz |
| Architecture | Silent Switcher 2nd generation |
| Internal Switches | Yes (top + bottom N-channel MOSFETs) |
| Điện áp yên tĩnh | Ultra-low (see datasheet for Iq) |
| Hiệu suất | > 95% peak |
| Khoảng nhiệt độ hoạt động | -40 C to +125 C (automotive grade) |
| Hộp | 32-pin LQFN EP (5 mm x 6 mm) |
| Kiểu lắp đặt | Surface Mount |
| Cấp MSL | 1 |
| Trạng thái RoHS | Compliant (#PBF suffix) |
Cấu hình chân LT8645SEV#PBF
| Chân 1 | SW — Switch node output to external inductor |
| Chân 2 | SW — Switch node output to external inductor |
| Chân 3 | SW — Switch node output to external inductor |
| Chân 4 | BST — Boost capacitor for top gate drive |
| Chân 5 | INTVCC — Internal 3.4V regulator bypass capacitor |
| Chân 6 | VIN — Main input supply voltage |
| Chân 7 | VIN — Main input supply voltage |
| Chân 8 | VIN — Main input supply voltage |
| Chân 9 | GND — Ground return |
| Chân 10 | PGND — Power ground return |
| Chân 11 | PGND — Power ground return |
| Chân 12 | PGND — Power ground return |
| Chân 13 | VOUT — Output voltage sense |
| Chân 14 | FB — Feedback input for adjustable output |
| Chân 15 | TR/SS — Timing resistor / soft-start |
| Chân 16 | RT — Timing resistor for switching frequency |
| Chân 17 | PG — Power good open-drain output |
| Chân 18 | EN/UV — Enable / undervoltage lockout |
| Chân 19 | NC — Not connected (per datasheet) |
| Chân 20 | NC — Not connected (per datasheet) |
| Chân 21 | NC — Not connected (per datasheet) |
| Chân 22 | NC — Not connected (per datasheet) |
| Chân 23 | BST2 — Boost capacitor for second top gate drive |
| Chân 24 | SW2 — Second switch node |
| Chân 25 | SW2 — Second switch node |
| Chân 26 | SW2 — Second switch node |
| Chân 27 | SYNC — Synchronization input for external clock |
| Chân 28 | FREQ — Frequency selection / spread spectrum |
| Chân 29 | VINSNS — Input voltage sense for feedforward |
| Chân 30 | TEST — Factory test pin (do not connect) |
| Chân 31 | AGND — Analog ground |
| Chân 32 | VOUTSNS — Output voltage remote sense |
Ứng dụng tiêu biểu
LT8645SEV#PBF phù hợp cho 6 Áp dụngs: Automotive Always-On Systems, Industrial 48 V Point-of-Load Conversion, Distributed Power Systems, Battery-Powered Portable Equipment, RF and Communication Power Rails, FPGA and ASIC Core Supplies.
Automotive Always-On Systems
The LT8645SEV#PBF is engineered for automotive always-on applications such as body control modules, HVAC controllers, and infotainment standby rails. Its 3.4 V to 65 V input range survives cold-crank down to 6 V and load-dump transients up to 35 V (and 65 V worst-case) without additional protection, while the second-generation Silent Switcher architecture cuts radiated EMI by 20-25 dB versus conventional buck ICs. At VIN = 12 V and VOUT = 3.3 V, the part delivers 8 A at >93% efficiency, and the 32-pin LQFN exposed pad handles thermal dissipation during 8 A peak loads. The AEC-Q100-style automotive temperature range (-40 C to +125 C) and ultra-low quiescent current suit battery-powered nodes that must remain alive in PARK for weeks.
Được đề xuất
Industrial 48 V Point-of-Load Conversion
In 48 V telecom and industrial bus architectures, the LT8645SEV#PBF steps the bus voltage down to 12 V, 5 V, or 3.3 V at the point-of-load. With 65 V input tolerance, it tolerates transients and ringing on the 48 V rail without external TVS clamps. The 8 A continuous output serves high-current POL nodes such as FPGA core rails, ASIC supplies, and motor driver logic, while the Silent Switcher topology passes CISPR 25 and CISPR 32 EMI without bulky input filters. Switching frequencies up to 2.2 MHz shrink the LC filter footprint below 100 mm^2, enabling compact placement next to the load.
Được đề xuất
Distributed Power Systems
The LT8645SEV#PBF fits as the intermediate bus converter in distributed power architectures where a front-end supply feeds 12 V or 24 V buses to multiple POL regulators. Its 95% peak efficiency at heavy loads reduces system cooling budget, and the 200 kHz to 2.2 MHz programmable switching frequency allows synchronization with downstream converters to avoid beat-frequency noise. The exposed-pad LQFN-32 package simplifies PCB layout and spreads heat across the ground pour, allowing 8 A continuous operation at 85 C ambient with proper copper area.
Được đề xuất
Battery-Powered Portable Equipment
For battery-powered industrial handhelds, test instruments, and portable medical devices, the LT8645SEV#PBF's ultra-low quiescent current extends standby time, and its high efficiency at light loads preserves runtime during active use. Operating from a 1S to 6S Li-ion pack (3.4 V to 25.2 V), it can generate 5 V or 3.3 V rails with >95% efficiency at moderate loads. The Silent Switcher topology eliminates the audible high-frequency whine that plagues conventional buck ICs in handheld audio equipment, making it suitable for portable speakers and Bluetooth audio products.
Được đề xuất
RF and Communication Power Rails
The LT8645SEV#PBF is well suited for powering RF transceivers, baseband processors, and clocking circuitry where low-noise, high-PSRR rails are required. The Silent Switcher architecture provides clean output voltage with minimal spurious content, eliminating interference with adjacent RF stages. At 8 A capability, the LT8645SEV can power a complete small-cell radio chain including the PA supply, transceiver, and digital baseband. The wide input range supports both battery and PoE-fed deployments, making it a versatile choice for IoT gateways.
Được đề xuất
FPGA and ASIC Core Supplies
FPGAs and ASICs require low-voltage, high-current core rails (0.97 V to 1.8 V typical) with tight regulation and fast transient response. The LT8645SEV#PBF delivers 8 A continuous to feed such loads, and its peak-current-mode control architecture provides excellent line and load transient performance. The wide 3.4 V to 65 V input range allows the part to be powered from a 5 V, 12 V, or 24 V intermediate rail depending on system architecture. Programmable switching up to 2.2 MHz allows the inductor to shrink below 1 microhenry, freeing board area near the FPGA.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho LT8645SEV#PBF — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | LT8645SEV-2#PBF | LT8646SEV#PBF | LT8645SIV#PBF | LT8645SJV#PBF | LT8645SIV#WPBF |
|---|---|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Package | 32-pin LQFN EP (5x6 mm) | 32-pin LQFN EP (5x6 mm) - same | 32-pin LQFN EP (5x6 mm) - same | 32-pin LQFN EP (5x6 mm) - same | 32-pin LQFN EP (5x6 mm) - same | 32-pin LQFN EP (5x6 mm) - same |
| Input Voltage Range | 3.4 V to 65 V | 3.4 V to 65 V | 3.4 V to 65 V | 3.4 V to 65 V | 3.4 V to 65 V | 3.4 V to 65 V |
| Maximum Output Current | 8 A | 8 A | 8 A | 8 A | 8 A | 8 A |
| Output Voltage Range | 0.97 V to 25 V | 0.97 V to 25 V | 0.97 V to 25 V | 0.97 V to 25 V | 0.97 V to 25 V | 0.97 V to 25 V |
| Switching Frequency Range | 200 kHz to 2.2 MHz | 200 kHz to 2.2 MHz | 200 kHz to 2.2 MHz | 200 kHz to 2.2 MHz | 200 kHz to 2.2 MHz | 200 kHz to 2.2 MHz |
| Quiescent Current | Standard (see datasheet) | 2.5 uA (ultra-low Iq) | Standard (see datasheet) | Standard (see datasheet) | Standard (see datasheet) | Standard (see datasheet) |
| Temperature Grade | Automotive -40C to +125C | Automotive -40C to +125C | Automotive -40C to +125C | Industrial -40C to +125C | Automotive -40C to +125C | Industrial -40C to +125C |
| RoHS Compliance | Yes (#PBF) | Yes (#PBF) | Yes (#PBF) | Yes (#PBF) | Yes (#PBF) | Yes (#WPBF) |
Bảo phân biệt quan trọng
- Second-generation Silent Switcher EMI reduction (vsConventional 65 V buck regulators)
- 65 V input range exceeds automotive load-dump requirements (vs42 V competitors)
- 8 A continuous from a compact LQFN-32 package (vsLarger SOIC-packaged competitors)
Ghi chú thiết kế
Follow the Analog Devices LT8645S reference PCB layout exactly to preserve Silent Switcher EMI performance. Place input capacitors (CIN) as close as possible to the VIN and PGND pins using short, wide traces to minimize the high-frequency hot loop. The exposed thermal pad must be soldered to a ground copper pour with at least 25 thermal vias to a bottom-side thermal pad. Per datasheet, deviating from the reference layout can increase EMI by 10-20 dB and compromise regulation stability at high VIN-VOUT differentials.
Estimated: At VIN=24 V, VOUT=5 V, IOUT=8 A, power dissipation is P = (VIN-VOUT) * IOUT = (24-5) * 8 = 152 W... correction: P_diss = (VIN - VOUT) * IOUT is incorrect for buck; correct formula P_diss = (VIN - VOUT) * IOUT * (1 - efficiency). With ~95% efficiency, P_diss approx 152 W * 0.05 = 7.6 W. Use the LQFN-32 exposed pad with at least 1 square inch of 2 oz copper on top and bottom layers, plus thermal vias. Without adequate copper, junction temperature can exceed 150 C at 8 A continuous load.
Do not exceed the absolute maximum VIN of 65 V - load-dump transients on 24 V automotive systems can reach 36 V steady-state and higher transient peaks. Place a TVS diode or input protection circuit if the application may exceed 65 V. Also, the BST capacitor must be a low-ESR ceramic (X7R/X5R, 0.1 uF typical) placed directly at the BST pin - using a polarized capacitor or omitting it causes top-side MOSFET drive failure. The INTVCC pin requires its own 1 uF bypass capacitor close to the pin.
Thông tin tuân thủ
RoHS compliant per #PBF suffix. AEC-Q100 qualified for automotive applications. Lead-free and halogen-free per ADI product documentation.
