M29F800FT55N3F2 - 8Mbit 5V NOR Flash 55ns | Micron
MPN: M29F800FT55N3F2 ✓ Hoạt độngM29F800FT55N3F2 Tóm tắt
Parallel NOR Flash is a non-volatile memory technology that connects directly to a microprocessor's address and data buses, allowing code to be executed in place (XIP) without first copying to RAM. Within the memory hierarchy, NOR Flash sits alongside SRAM and DRAM in embedded systems as the primary boot and code-storage medium, complemented by NAND Flash and serial SPI Flash for bulk data storage. Its random-access architecture, with access times measured in nanoseconds, is what distinguishes NOR from block-oriented NAND devices.
Key features of the M29F800FT55N3F2 include dual organization (1M x8-bit or 512K x16-bit, selectable via the BYTE pin), a fast 55 ns access time suitable for zero-wait-state microprocessor interfacing, single 5.0V supply for both read and write/erase operations, and a top boot block architecture (T suffix) that places the protected boot code block at the top of the memory map. The device is programmed in-system using the standard 5.0V VCC supply; no separate 12V VPP is required for program or erase operations.
The memory array is organized into uniformly sized blocks with hardware sector-protection capability, block erase, and fast word/byte programming. The 48-pin TSOP surface-mount package keeps the footprint compact for embedded CPU boards, and the tape-and-reel suffix (T/R in the N3F2 ordering code) supports automated pick-and-place assembly in volume production.
Typical applications include boot code storage for industrial controllers, telecom line cards, networking equipment, set-top boxes, and legacy 5V embedded systems where in-place code execution and long-term data retention are required. The 5V-only operation makes it a direct fit for older microprocessor families that run on 5V rails.
When designing with this device, verify whether your boot code must reside in the top or bottom of the address map: the FT (top boot) and FB (bottom boot) variants share the same package and pinout but differ in block ordering. Always confirm block organization against your linker map before substituting.
This page synthesizes distributor pricing, same-family drop-in alternatives, and practical design notes not found in the manufacturer datasheet, with pricing referenced as of 2026-09-05.
Bộ thay thế dễ dàng lắp đặt cho M29F800FT55N3F2 — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với M29F800FT55N3F2 (cùng hình factor và footprint) — khác nhau ở Organization, Memory Type, Package, Packaging, Interface.
M29F800FB55N3F2
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →M29F800FT55M3F2
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →M29F400FT55N3F2
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →M29F160FT55N3F2
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →MBM29F800TA-55PFTN
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
M29F800FT55N3F2 Tỷ lệ tối đa & tính chất điện
| Kiểu bộ nhớ | NOR Flash, Parallel |
| Kích thước bộ nhớ | 8 Mbit |
| Tổ chức | 1M x 8 bit / 512K x 16 bit |
| Điện áp cung cấp | 5 V (single supply) |
| Access Time | 55 ns |
| Giao diện | Parallel |
| Boot Block Architecture | Top boot block (T) |
| Programming Voltage | 5.0 V VCC (no 12 V VPP required) |
| Hộp | 48-pin TSOP |
| Kiểu lắp đặt | Surface Mount |
| Packaging | Tape & Reel (T/R) |
Hướng dẫn cấu hình chân M29F800FT55N3F2 48-pin tsop
Cấu hình chân cho M29F800FT55N3F2 (48-pin tsop gói). IC số này bao gồm chân GPIO, giao diện truyền thông (UART, SPI, I2C) và chân nguồn. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết các chức năng chân thay thế và tùy chọn cấu hình. Cực kỳ quan trọng cho thiết kế hệ thống tích hợp và lập trình PCB.
Không có dữ liệu chân cụ thể sẵn có cho M29F800FT55N3F2.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
M29F800FT55N3F2 phù hợp cho 6 Áp dụngs: Industrial Controller Boot Code Storage, Telecom Line Card Code Storage, Networking Equipment Boot ROM, Set-Top Box Firmware Memory, Test and Measurement Instrument Firmware, Automotive and Legacy Embedded Retrofit.
Industrial Controller Boot Code Storage
The M29F800FT55N3F2 stores boot firmware and application code for 5V industrial PLCs and motor control boards. Its 55 ns asynchronous access time allows the microprocessor to execute code in place (XIP) with zero wait states at typical 8/16-bit bus frequencies, and the top boot block hardware-protects reset code against accidental erase during field reprogramming. Because program and erase complete at the standard 5.0V VCC, no high-voltage pump circuitry is needed on the board, reducing BOM cost and board area. The 48-pin TSOP surface-mount package withstands industrial assembly flow and provides the large parallel bus required by legacy 8051-class, 68K-class, and similar 5V microprocessor families.
Được đề xuất
Telecom Line Card Code Storage
Telecom line cards and network interface boards traditionally use 5V parallel NOR Flash to hold protocol firmware and DSP load images. The M29F800FT55N3F2 fits these designs directly: the 512K x16 organization matches 16-bit bus widths common on telecom backplanes, and the 55 ns access time supports in-place execution of monitor code while larger application images are shadowed to RAM. The RB (ready/busy) output provides a hardware handshake for erase/program completion, important during in-service firmware upgrades. Its top boot block can hold the boot monitor with sector protection enabled, and 5V-only operation aligns with legacy card power rails, avoiding level-shift circuitry.
Được đề xuất
Networking Equipment Boot ROM
Routers, switches, and access equipment from the 5V era use parallel NOR Flash as the boot ROM that initializes the CPU and loads the main OS image. The M29F800FT55N3F2 provides 8 Mbit capacity - sufficient for a U-Boot-style bootloader plus a compressed OS image - with the 55 ns access time needed for early code execution before SDRAM is initialized. Hardware sector protection on the boot block prevents a failed field upgrade from bricking the unit, and in-system programming at 5.0V VCC allows recovery over the CPU bus without socketed parts or external programmers. The x8/x16 selectable organization simplifies reuse of one firmware build across board revisions.
Được đề xuất
Set-Top Box Firmware Memory
Legacy set-top box and broadcast receiver designs rely on 5V parallel NOR Flash to hold the bootloader and configuration firmware. The M29F800FT55N3F2 offers the random-access nanosecond-class read performance serial Flash cannot provide, enabling the decoder CPU to start fetching reset vectors immediately at power-up. The top boot block keeps the secure boot sector isolated and protected, while uniform block erase supports clean over-the-air firmware update schemes. Its single 5V supply matches the power architecture of these consumer platforms, and the 48-pin TSOP package suits the moderate board density of set-top mainboards, with tape-and-reel supply supporting volume SMT assembly.
Được đề xuất
Test and Measurement Instrument Firmware
Bench instruments and rack-mounted measurement equipment built around 5V microprocessor buses store calibration data, self-test routines, and main firmware in parallel NOR Flash. The M29F800FT55N3F2 delivers 55 ns read access so diagnostic code runs in place during power-on self-test, and its in-system programmability at 5.0V lets manufacturing lines update firmware through the instrument's own CPU bus, eliminating socketed EPROMs and UV erasers. Sector protection safeguards the calibration block against corruption during upgrades. The dual x8/x16 organization lets one PCB design serve both cost-reduced 8-bit variants and full 16-bit bus variants, consolidating sourcing across a product family.
Được đề xuất
Automotive and Legacy Embedded Retrofit
Service organizations maintaining ECU boards, engine controllers, and 5V embedded legacy systems frequently need replacement parallel NOR Flash with original 5V signaling. The M29F800FT55N3F2 directly replaces aging AMD/Fujitsu 29F800-class parts: the 55 ns timing and 5V-only operation preserve original bus timing margins, the top boot block matches typical ECU reset-vector placement, and the 48-pin TSOP footprint matches legacy PCB land patterns. Because programming needs only 5.0V VCC, field reprogramming via the OBD or service connector remains possible. Designers should confirm block organization and endurance requirements against the original part datasheet before retrofitting.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho M29F800FT55N3F2 — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | M29F800FB55N3F2 | M29F800FT55M3F2 | M29F400FT55N3F2 | MBM29F800TA-55PFTN |
|---|---|---|---|---|---|
| Package | 48-pin TSOP | 48-pin TSOP - same | 48-pin TSOP family | 48-pin TSOP - same | 48-pin TSOP - same |
| Brand | Micron Technology | Micron Technology | Micron Technology | Micron Technology | Fujitsu |
| Density | 8 Mbit | 8 Mbit | 8 Mbit | 4 Mbit | 8 Mbit |
| Supply Voltage | 5 V | 5 V | 5 V | 5 V | 5 V |
| Access Time | 55 ns | 55 ns | 55 ns | 55 ns | 55 ns |
| Boot Block Position | Top boot | Bottom boot | Top boot | Top boot | Top boot |
| Organization | 1M x8 / 512K x16 | 1M x8 / 512K x16 | 1M x8 / 512K x16 | 512K x8 / 256K x16 | 1M x8 / 512K x16 |
| Programming Supply | 5.0 V VCC in-system (no 12V VPP) | 5.0 V VCC in-system | 5.0 V VCC in-system | 5.0 V VCC in-system | 5.0 V VCC in-system (no 12V VPP) |
Bảo phân biệt quan trọng
- Top boot block architecture for reset-vector protection (vsM29F800FB55N3F2)
- Full 8 Mbit density in the 48-pin TSOP footprint (vsM29F400FT55N3F2)
- Proven cross-brand second source (vsMBM29F800TA-55PFTN)
- 5V-only in-system programming (vsAll listed alternatives)
Ghi chú thiết kế
Decouple VCC with at least a 0.1 uF ceramic capacitor placed within a few millimeters of the 48-pin TSOP power pins, plus one bulk 4.7-10 uF capacitor per device. Parallel NOR draw significant transient current during program and erase operations; an inadequate decoupling network causes VCC droop that can corrupt the programming operation. Tie the BYTE pin firmly high or low (never left floating) to fix the x8 or x16 data bus width, and pull all unused address inputs to a defined logic level.
The most common substitution error is confusing top-boot (FT) with bottom-boot (FB) variants. Both are pin-to-pin identical in the 48-pin TSOP package, but the protected boot block sits at opposite ends of the address map. A board designed around top-boot reset vectors will fail with an FB part even though the footprint matches. Additionally, verify the sector/erase block organization against your linker map and flash driver sector table before swapping any M29F family member; block sizes and ordering differ across densities (400/800/160).
On 5V parallel buses, keep address and data trace lengths matched within roughly 20 mm and add series termination (22-33 ohm) on fast CPU outputs driving the Flash to control ringing. Use the RB (ready/busy) output with an interrupt or polling scheme rather than software-only polling of the status bits to make program/erase completion detection robust. Ensure the write-enable path includes proper bus contention control - never assert CE and OE simultaneously with WE active during reads, as this can drive the data bus into contention.
Estimated: read-mode supply current and standby current for this exact ordering code were not stated in the provided data ([DATA_NEEDED: ICC read]); consult the manufacturer datasheet current tables. As a design guideline, budget VCC at 5.0V +/- 10% per the M29F family specification and ensure the 5V rail can supply the peak program/erase current of the device plus margin. In multi-Flash systems, stagger erase operations or share a common bulk capacitor bank to avoid aggregate inrush collapsing the rail.
Thông tin tuân thủ
Compliance status for this exact ordering code was not stated in the provided web data. Confirm RoHS/REACH/lead-free status via Micron's product page or a material declaration request.
