MAX313CUE+ - Quad SPST CMOS Analog Switch | ADI
MPN: MAX313CUE+ ✓ Hoạt độngMAX313CUE+ Tóm tắt
A CMOS analog switch is a voltage-controlled semiconductor device that routes analog or digital signals between circuit nodes. The MAX313 belongs to the analog switch and multiplexer hierarchy, where an analog switch performs point-to-point routing and a multiplexer connects multiple signals to a common channel. Its SPST configuration provides one normally open path per switch, making it suitable for isolation, signal selection, test-fixture routing, and bidirectional analog-signal control.
The four channels can conduct equally well in either direction. The MAX313CUE+ combines low on-resistance with channel-to-channel matching of 1.5 ohms maximum and on-resistance flatness of 2 ohms maximum over the specified signal range. These characteristics help minimize gain error and distortion when several switched channels must present similar resistance to downstream circuitry. It also provides low leakage and low power consumption for precision and power-sensitive systems.
The MAX313 family operates from a wide supply range and supports rail-to-rail signal handling. According to the Analog Devices MAX313 product page, the devices are pin compatible with the DG411, DG412, and DG413 families. The manufacturer also specifies guaranteed ESD protection greater than 2000 V per Method 3015.7 and crosstalk above 96 dB at 20 kHz, helping protect sensitive analog paths and limit interaction between adjacent channels.
Typical uses include precision test and measurement systems, analog signal-conditioning modules, battery-powered instrumentation, industrial control interfaces, and signal-isolation networks. The device can route sensor outputs, test signals, or external inputs without introducing the continuous power loss associated with a permanently conducting analog path. It is particularly useful when signal integrity, repeatable channel resistance, and low off-state leakage are more important than maximum switching speed.
When laying out a MAX313CUE+ board, follow the TSSOP-16 pin-assignment table in the manufacturer datasheet and keep high-impedance routes short to minimize leakage pickup. Place supply decoupling close to the device, and evaluate switching transients when the source impedance is high. The normally open architecture requires the correct drive polarity at each control input; consult the control-input truth table before changing logic levels.
This product record combines the manufacturer specifications, package information, replacement references, and practical design guidance into one engineering-focused view. It also identifies same-package alternatives and explains when their electrical or environmental differences matter, helping designers select the correct switch without introducing a footprint change.
Bộ thay thế dễ dàng lắp đặt cho MAX313CUE+ — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
MAX313EUE+
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
MAX313LEUE+
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
MAX313LEUE+T
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
DG411LE+
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
DG412LE+
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
DG413LE+
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
MAX313CUE+ Tỷ lệ tối đa & tính chất điện
| Number of Switches | 4 channels |
| Switch Configuration | 4 x SPST normally open |
| On-Resistance | 10 ohms maximum |
| Typical On-Resistance | 6.5 ohms |
| On-Resistance Matching Between Channels | 1.5 ohms maximum |
| On-Resistance Flatness | 2 ohms maximum over specified signal range |
| Single-Supply Operating Range | 4.5 V to 30 V |
| Dual-Supply Operating Range | -4.5 V to -20 V and +4.5 V to +20 V |
| Signal Handling | Rail-to-rail |
| ESD Protection | >2000 V per Method 3015.7 |
| Crosstalk | >96 dB at 20 kHz |
| Conduction Direction | Bidirectional |
| Hộp | 16-pin TSSOP |
| Kiểu lắp đặt | Surface mount |
| Off-State Leakage | 2.5 nA at +85 degrees C |
Hướng dẫn cấu hình chân MAX313CUE+ 16-pin tssop
Cấu hình chân cho MAX313CUE+ (16-pin tssop gói). Số thứ tự chân, chức năng và sơ đồ kết nối được xác định trong tài liệu thông số kỹ thuật của nhà sản xuất. Tham khảo nó để biết footprint và hướng dẫn hàn chính xác.
Không có dữ liệu chân cụ thể sẵn có cho MAX313CUE+.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
MAX313CUE+ phù hợp cho 6 Áp dụngs: Precision Test and Measurement Systems, Analog Signal Conditioning, Battery-Powered Instrumentation, Industrial Control and Sensor Interface, Automated Test Fixture Signal Routing, Signal Isolation and Safety Routing.
Precision Test and Measurement Systems
MAX313CUE+ fits switch matrices and measurement fixtures that must route several test signals with predictable resistance. Its 6.5 ohms typical on-resistance, 1.5 ohms maximum matching between channels, and 2 ohms maximum flatness reduce channel-dependent gain variation. The four SPST channels can independently connect a source, instrument input, or calibration node. Because the device supports rail-to-rail signal handling, it can be placed near the measured signal rather than deep inside a remote analog section. The design should still account for switch charge injection and leakage when the connected source impedance is high.
Được đề xuất
Analog Signal Conditioning
MAX313CUE+ can route sensor outputs, reference signals, or amplifier inputs through a selectable conditioning network. Its maximum on-resistance of 10 ohms and typical value of 6.5 ohms are low compared with many analog switch networks, limiting voltage division when the downstream input impedance is substantially higher. Matching of 1.5 ohms maximum helps maintain similar transfer behavior across four channels. For high-gain signal paths, place the switch close to the amplifier input and keep the disabled channel's leakage from contributing to offset errors. The actual error budget should include the source impedance and amplifier input bias current.
Được đề xuất
Battery-Powered Instrumentation
MAX313CUE+ is appropriate for portable measurement equipment that needs to disconnect external inputs to reduce loading, leakage, or unwanted signal paths. The MAX313 family's low-leakage behavior is identified as 2.5 nA at +85 degrees C, helping preserve accuracy when high-impedance sensors are disconnected. Four independently controlled SPST paths let one microcontroller or analog front end select among probes or test channels. Single-supply operation from 4.5 V to 30 V covers battery-derived rails and higher industrial rails when appropriate. Designers should confirm the control levels and operating-temperature grade for the intended enclosure and battery-charging environment.
Được đề xuất
Industrial Control and Sensor Interface
MAX313CUE+ can isolate or select signals at the boundary between an industrial controller and external sensor wiring. The normally open SPST configuration prevents a connected signal from driving the source when the switch is off, while bidirectional conduction supports use with either digital or analog signals. Its 10 ohms maximum on-resistance is suitable for many low- and medium-impedance industrial interfaces. Rail-to-rail handling supports signals extending across the supply rails. For long external cables, however, surge and ESD requirements must be evaluated separately, and the manufacturer-rated greater-than-2000 V ESD protection should not be treated as a complete industrial surge solution.
Được đề xuất
Automated Test Fixture Signal Routing
MAX313CUE+ supports automated fixtures that connect DUT pins, supplies, or external loads under software control. The four channels provide independently isolated routing paths, and the 1.5 ohms maximum channel matching can improve repeatability across multiple fixture positions. The specified on-resistance flatness of 2 ohms helps limit distortion when signals occupy a significant portion of the available signal range. The TSSOP-16 package supports compact fixture electronics close to the DUT. Keep routed lines short, maintain a continuous ground reference, and validate switching transients and charge injection at the speed and source impedance used by the test system.
Được đề xuất
Signal Isolation and Safety Routing
MAX313CUE+ can disconnect a signal source to establish a higher-impedance state in instrumentation and signal-conditioning equipment. Its normally open topology and low off-state leakage help reduce unintended coupling when a channel is inactive. The MAX313 family's greater-than-2000 V ESD protection rating adds device-level robustness, while the 10 ohms maximum on-resistance keeps the conducting-state loss modest. Isolation in this context is functional signal disconnection rather than a reinforced safety barrier; creepage, clearance, insulation, and applicable medical or industrial isolation requirements must be handled separately by the complete system design.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho MAX313CUE+ — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | MAX313EUE+ | MAX313LEUE+ | DG411LE+ |
|---|---|---|---|---|
| Package | TSSOP-16 | TSSOP-16 | TSSOP-16 | TSSOP-16 |
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Number of Channels | 4 channels | 4 channels | 4 channels | 4 channels |
| Switch Configuration | 4 x SPST normally open | 4 x SPST normally open | 4 x SPST normally open | 4 x SPST |
| Maximum On-Resistance | 10 ohms | 10 ohms | 10 ohms | Not specified in the verified product information |
| Typical On-Resistance | 6.5 ohms | 6.5 ohms | 6.5 ohms | Not specified in the verified product information |
| Single-Supply Maximum | 30 V | 30 V | 30 V | Not specified in the verified product information |
| On-Resistance Matching | 1.5 ohms maximum | 1.5 ohms maximum | 1.5 ohms maximum | Not specified in the verified product information |
| On-Resistance Flatness | 2 ohms maximum over specified signal range | 2 ohms maximum over specified signal range | 2 ohms maximum over specified signal range | Not specified in the verified product information |
| ESD Protection | >2000 V per Method 3015.7 | >2000 V per Method 3015.7 | >2000 V per Method 3015.7 | Not specified in the verified product information |
Bảo phân biệt quan trọng
- Lower typical conduction resistance (vsDG411LE+)
- Guaranteed channel matching (vsDG412LE+)
- Specified on-resistance flatness (vsDG413LE+)
- Broad dual-supply operating capability (vsMAX313EUE+)
Ghi chú thiết kế
Place the MAX313CUE+ close to the switched-signal source and destination, and keep connected traces short. Long, high-impedance routes increase capacitive pickup from control edges and can magnify charge injection when the source impedance is high. Use the pin-description and typical application diagrams in the MAX313 manufacturer datasheet when assigning the TSSOP-16 footprint. Keep the ground return continuous under and around the device so switching current does not share a high-impedance path with the analog signal.
Include the switch on-resistance, source impedance, and load impedance in the gain-error calculation. The MAX313CUE+ has 6.5 ohms typical and 10 ohms maximum on-resistance, so using only the typical value can understate divider error at the guaranteed limit. Because channel matching is specified at 1.5 ohms maximum and flatness at 2 ohms maximum, use those limits when comparing measurement channels. For a 10 kilohm source, the maximum 10 ohm switch resistance changes the divider ratio by approximately 0.1%.
Do not treat the normally open SPST switch as a low-impedance permanent connection. Verify the control truth table and logic levels from the MAX313 manufacturer datasheet before driving the control inputs. Also distinguish the MAX313CUE+ commercial ordering code from same-family extended-temperature or tape-and-reel variants. The physical TSSOP-16 footprint can remain unchanged, but temperature grade, qualification, order packing, and supply limits can differ between suffixes.
Analyze adjacent-channel coupling and control-edge energy rather than relying only on the 96 dB crosstalk figure at 20 kHz. The specified crosstalk condition is frequency-dependent and does not represent every practical signal bandwidth, source impedance, or PCB routing environment. Keep the unused channel properly driven or terminated according to the manufacturer truth table, maintain short control traces, and use a quiet ground reference. Validate fast-switching nodes with an oscilloscope in the final layout because package and trace parasitic effects can influence observed transient behavior.
Thông tin tuân thủ
The verified product information does not explicitly state the RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status of MAX313CUE+. The plus suffix alone should not be treated as a complete compliance declaration. Request current manufacturer material-declaration and qualification records for the exact ordering code.