MAX3221CDBRG4 - 250kbps RS-232 Transceiver | Texas Instruments
MPN: MAX3221CDBRG4 ✓ Hoạt độngMAX3221CDBRG4 Tóm tắt
An RS-232 transceiver is an interface IC that translates logic-level signals between a host or controller and a RS-232 link. Within the signal-chain hierarchy, it belongs to the RS-232 interface, line-driver and receiver, communications-interface, and semiconductor categories. The MAX3221CDBRG4 is intended for equipment that needs one bidirectional serial port while operating from a 3 V to 5.5 V system supply.
Key features include a maximum data rate of 250 kbit/s, ±15 kV ESD protection on the serial-port connection pins, and a low shutdown supply current. According to the manufacturer datasheet, the device provides AutoShutdown operation and supports true +3 V to +5.5 V supplies. Its integrated charge pumps reduce the external component count compared with a discrete RS-232 interface implementation.
The MAX3221 family combines a driver and receiver with internal level-shifting circuitry. The charge-pump section develops positive and negative voltage rails from the single device supply, allowing the line interface to produce RS-232-compatible output levels. The receiver converts the bipolar serial signal back to a logic-compatible signal, while the dedicated receiver-enable control can place the receiving path in a reduced-power state when it is not required.
Typical uses include industrial serial-port adapters, point-to-sale equipment, test and measurement instruments, embedded control systems, and legacy peripheral connections. The single-channel arrangement is especially suitable for compact systems that need one RS-232 port but no multi-port RS-232 expansion.
When designing around the MAX3221CDBRG4, preserve the charge-pump capacitor and bypass-capacitor placement recommended in the manufacturer datasheet. Confirm that the host interface uses the correct logic voltage and that the receiver-enable polarity matches the controller firmware. The 16-pin SSOP footprint also requires careful solder-joint inspection because lead pitch and package density can complicate rework.
This product page consolidates the electrical limits, interface function, packaging information, and practical design considerations for the MAX3221CDBRG4. It also identifies verified drop-in alternatives and organizes the selection trade-offs by speed, supply range, temperature grade, and interface configuration.
Bộ thay thế dễ dàng lắp đặt cho MAX3221CDBRG4 — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với MAX3221CDBRG4 (cùng hình factor và footprint) — khác nhau ở AutoShutdown Supply Current, ESD Protection, Interface Standard, Package, Product Type.
MAX3221CDBR
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →MAX3221EIDBR
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →MAX3221EAE+
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →MAX3221CDBRG4 Thông số kỹ thuật
| Product Type | Single-channel RS-232 line driver/receiver |
| Number of Drivers | 1 driver |
| Number of Receivers | 1 receiver |
| Supply Voltage Range | 3 V to 5.5 V |
| Maximum Data Rate | 250 kbit/s |
| ESD Protection | ±15 kV |
| Hộp | 16-pin SSOP, 0.209 inch (5.30 mm) width |
| Kiểu lắp đặt | Surface mount |
| Operating Supply Range | 3 V to 5.5 V |
| AutoShutdown Supply Current | 1 µA |
| Driver and Receiver Count | 1/1 |
| Interface Standard | RS-232 |
| ESD Test Model | Human-Body Model (HBM) |
| Compliance Standard | TIA/EIA-232-F and ITU V.28 |
| Packaging | Tape and reel |
Hướng dẫn cấu hình chân MAX3221CDBRG4 16-pin ssop, 0.209 inch (5.30 mm) width
Cấu hình chân cho MAX3221CDBRG4 (16-pin ssop, 0.209 inch (5.30 mm) width gói). Số thứ tự chân, chức năng và sơ đồ kết nối được xác định trong tài liệu thông số kỹ thuật của nhà sản xuất. Tham khảo nó để biết footprint và hướng dẫn hàn chính xác.
Không có dữ liệu chân cụ thể sẵn có cho MAX3221CDBRG4.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
MAX3221CDBRG4 phù hợp cho 6 Áp dụngs: Industrial Serial-Port Adapter, Point-of-Sale Terminal Interface, Test and Measurement Equipment, Embedded Controller Service Port, Legacy Peripheral Connectivity, Portable Diagnostic Interface.
Industrial Serial-Port Adapter
The MAX3221CDBRG4 fits a compact industrial RS-232 adapter because it combines one driver and one receiver in a single 16-pin SSOP package. Its 3 V to 5.5 V supply range supports embedded 3.3 V and 5 V control hardware, while the 250 kbit/s maximum data rate covers standard asynchronous serial links. The ±15 kV ESD rating on the connection pins adds useful protection for a cable interface exposed to electrostatic discharge. A designer should still evaluate the exact temperature grade and use appropriately routed protection for severe industrial environments.
Được đề xuất
Point-of-Sale Terminal Interface
A point-of-sale terminal can use the MAX3221CDBRG4 when it needs one legacy serial connection to a peripheral, printer, or service interface. The device operates from 3 V to 5.5 V, which allows it to share power with common embedded terminal logic, and its single-channel architecture preserves board area. Operation at up to 250 kbit/s is suitable for conventional RS-232 traffic. Place the charge-pump capacitors and bypass capacitor close to their pins, and route the cable-side interface away from sensitive processor circuitry.
Được đề xuất
Test and Measurement Equipment
The MAX3221CDBRG4 is appropriate for test and measurement equipment that retains an RS-232 control or configuration port. A 250 kbit/s interface rate is sufficient for many command and status exchanges, while the dedicated receiver-enable pin can reduce activity when the receiver is not needed. Its 16-pin SSOP package allows the interface to fit beside a controller without occupying a board edge as much as a larger package. Verify the enclosure ground and cable-return strategy because an RS-232 transceiver alone does not eliminate ground-loop or surge concerns.
Được đề xuất
Embedded Controller Service Port
The MAX3221CDBRG4 can provide a service port for an embedded controller that needs configuration access over RS-232. The 3 V to 5.5 V supply range supports common controller rails, and the 1 µA shutdown supply current described for the MAX3221 family helps with low-power operation when the port is inactive. The receiver-enable control offers another way to manage the receive path. Firmware should control that pin carefully so that line states are interpreted predictably during startup and shutdown.
Được đề xuất
Legacy Peripheral Connectivity
The MAX3221CDBRG4 enables a modern controller to communicate with a legacy peripheral that exposes only an RS-232 port. The integrated dual charge-pump circuit generates the required bipolar voltage levels from one 3 V to 5.5 V supply, avoiding a separate negative-rail generator. The device supports signaling rates up to 250 kbit/s and includes ±15 kV ESD protection on the serial connection pins. Confirm the peripheral's logic timing, connector wiring, and handshake requirements before finalizing the interface.
Được đề xuất
Portable Diagnostic Interface
The MAX3221CDBRG4 can support a portable diagnostic or programming adapter when one RS-232 channel is sufficient. Its 1 µA shutdown current is useful where the adapter may remain connected to a battery-powered system for extended periods, while the compact 16-pin SSOP package supports space-constrained assemblies. The 3 V to 5.5 V input range accommodates common portable-system rails, and the 250 kbit/s limit is adequate for many configuration protocols. A robust mechanical connector and cable strain relief remain important in portable equipment.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho MAX3221CDBRG4 — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | MAX3221CDBR | MAX3221EIDBR | MAX3221EAE+ |
|---|---|---|---|---|
| Package | 16-pin SSOP | 16-pin SSOP | 16-pin SSOP | 16-pin SSOP |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Transceiver Type | Single-channel RS-232 driver/receiver | Single-channel RS-232 driver/receiver | Single-channel RS-232 driver/receiver | Single-channel RS-232 driver/receiver |
| Driver/Receiver Count | 1/1 | 1/1 | 1/1 | 1/1 |
| Ordering Suffix | CDBRG4 | CDBR | EIDBR | EAE+ |
Bảo phân biệt quan trọng
- Single-channel integration in a compact package (vsMAX3221EIDBR)
- 3 V to 5.5 V operation (vsMAX3221CDBR)
- Integrated ESD protection on serial connections (vsMAX3221EAE+)
Ghi chú thiết kế
Place the charge-pump capacitors, supply bypass capacitor, and input/output network components exactly as shown in the typical applications circuit in the Texas Instruments MAX3221 datasheet. Keep the charge-pump traces short and avoid routing them beneath noisy digital or switching-current paths. The 16-pin SSOP footprint should be checked against the manufacturer land pattern before PCB release, including lead pitch, toe geometry, and exposed-pad assumptions if any.
Connect the RS-232 connector directly to the driver, receiver, and protected serial pins while keeping the high-voltage charge-pump section separated from sensitive analog or high-impedance nodes. Maintain a clear return path from the connector ground to the circuit ground and use the shortest practical route between the transceiver and connector protection components. This reduces capacitive coupling from cable transients and improves ESD-current survivability.
Do not assume that all MAX3221 ordering suffixes are automatically interchangeable in every production program. Confirm the exact temperature grade, package, lead configuration, device marking, and ESD rating in the manufacturer ordering information before releasing a replacement. Also ensure firmware interprets the receiver-enable polarity correctly; otherwise the software may read an invalid line state during startup or shutdown.
Thông tin tuân thủ
The manufacturer datasheet states that the RS-232 interface meets or exceeds TIA/EIA-232-F and ITU V.28 requirements. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status were not confirmed for the exact MAX3221CDBRG4 ordering code.