MAX3221EIPW - 250kbps Single RS-232 Transceiver | TI
MPN: MAX3221EIPW ✓ Hoạt độngMAX3221EIPW Tóm tắt
An RS-232 transceiver is an interface IC that converts logic-level UART signals into differential, bipolar RS-232 levels and converts received RS-232 signals back into logic-compatible levels. The MAX3221E belongs to the RS-232 transceiver family within interface ICs and power-management-adjacent signal-conditioning devices. It provides the electrical interface between an asynchronous communication controller and a serial-port connector.
The MAX3221E uses a single power supply and an on-chip charge pump with four small external capacitors. Its single driver and single receiver arrangement suits point-to-point serial links, while the enhanced ESD protection helps improve robustness at connector-facing pins. Operation across a 3V to 5.5V supply range supports both 3.3V and 5V system rails.
The device meets TIA/EIA-232-F requirements and provides IEC 61000-4-2 ESD protection. These qualifications are important because RS-232 implementations frequently connect through external connectors where cables and ESD events can introduce transient voltage. The MAX3221EIPW is therefore suitable for industrial control links, service interfaces, and embedded equipment requiring a compact single-channel RS-232 solution.
Typical uses include configuring a UART port on an embedded controller, upgrading an industrial peripheral that still uses an RS-232 connector, and creating a service or debug link between a host computer and field equipment. Because the interface is single-channel, applications needing multiple simultaneous RS-232 ports generally require additional transceiver channels or separate interface devices.
Place the four charge-pump capacitors close to their assigned pins, and route the RS-232 driver and receiver traces as a protected cable-side interface. Keep logic-side UART traces away from connector and charge-pump nodes, provide a stable ground return, and verify the external protection network against the system’s ESD requirements.
This page combines the manufacturer’s electrical specifications, package details, qualified substitute analysis, and practical PCB guidance. It also highlights where MAX3221E family alternatives share the same TSSOP-16 footprint and where their shutdown, enable, or ESD characteristics require verification before replacement.
Bộ thay thế dễ dàng lắp đặt cho MAX3221EIPW — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với MAX3221EIPW (cùng hình factor và footprint) — khác nhau ở Product Type, Number of Drivers, Number of Receivers, Supply Voltage Range, Maximum Data Rate.
MAX3221CPWR
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
MAX3221ECPWR
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →MAX3221IPWR
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →MAX3221EIPW Thông số kỹ thuật
| Product Type | Single-channel RS-232 line driver and receiver |
| Supply Voltage Range | 3V to 5.5V |
| Maximum Data Rate | 250kbps |
| Number of Drivers | 1 driver |
| Number of Receivers | 1 receiver |
| RS-232 ESD Protection | ±15kV |
| ESD Standard | IEC 61000-4-2 |
| RS-232 Standard Compliance | TIA/EIA-232-F |
| Charge-Pump Capacitors Required | 4 external capacitors |
| Hộp | 16-pin TSSOP |
| Kiểu lắp đặt | Surface mount |
| Loại giao diện | Full RS-232 transceiver |
| Driver and Receiver Count | 1/1 transceiver |
Hướng dẫn cấu hình chân MAX3221EIPW 16-pin tssop
Cấu hình chân cho MAX3221EIPW (16-pin tssop gói). Số thứ tự chân, chức năng và sơ đồ kết nối được xác định trong tài liệu thông số kỹ thuật của nhà sản xuất. Tham khảo nó để biết footprint và hướng dẫn hàn chính xác.
Không có dữ liệu chân cụ thể sẵn có cho MAX3221EIPW.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
MAX3221EIPW phù hợp cho 6 Áp dụngs: Industrial Control Console, Embedded UART-to-RS-232 Bridge, Point-to-Point Serial Link, Instrument Service Interface, Security and Access Controller, Portable Diagnostic Connector.
Industrial Control Console
The MAX3221EIPW is suitable for connecting an industrial controller or service terminal that still uses an RS-232 port. Its 3V-to-5.5V operating range permits use with 3.3V or 5V embedded systems, while the 250kbps data rate supports administrative commands, configuration transfers, and diagnostic traffic. The single driver and receiver provide the required levels between a UART controller and a DB9 or terminal connector. Its ±15kV IEC 61000-4-2 protection is particularly relevant where the cable is exposed to human contact. Designers should still include appropriate common-mode and surge protection for long industrial runs.
Được đề xuất
Embedded UART-to-RS-232 Bridge
The MAX3221EIPW bridges the logic-level UART pins of an embedded controller to a full RS-232 port. Its single 3V-to-5.5V supply simplifies integration with common embedded processors, while 250kbps operation is appropriate for configuration commands, firmware-console traffic, and short control exchanges. The internal charge pump needs only four external capacitors, reducing board area compared with a discrete driver-receiver implementation. A key layout consideration is to separate the cable-side RS-232 traces from sensitive UART and processor signals. Firmware should also account for RS-232 level inversion and ensure that the selected UART supports the required baud rate.
Được đề xuất
Point-to-Point Serial Link
The MAX3221EIPW provides one transmitter and one receiver for point-to-point communication between two asynchronous systems. At up to 250kbps, it is suitable for short control and monitoring links where a modern multi-protocol transceiver would add unnecessary cost or complexity. The single-supply architecture supports both 3.3V and 5V systems, and the charge-pump arrangement allows the interface to operate without a separate bipolar supply. When laying out the link, use a continuous signal and ground return, keep connector protection close to the entry point, and verify that the far-end UART receiver recognizes the bipolar RS-232 signaling correctly.
Được đề xuất
Instrument Service Interface
The MAX3221EIPW can provide a service port for laboratory, test, and measurement equipment that retains an RS-232 configuration interface. The 250kbps capability is more than adequate for command exchange, calibration files, and diagnostic logs, while the single TSSOP-16 package supports compact front-panel or board-level implementations. The ±15kV IEC ESD rating on the RS-232 pins adds protection at a connector that operators may contact frequently. For portable instruments, ensure the chassis and logic grounds follow the required RS-232 topology, and place any additional surge protection outside the logic-side routing area.
Được đề xuất
Security and Access Controller
The MAX3221EIPW can add an RS-232 maintenance channel to access-control or security equipment without consuming a dedicated multichannel interface IC. A 250kbps RS-232 link is suitable for configuration exchange, event-log retrieval, and controlled commissioning commands when the system already supports this legacy physical interface. The 3V-to-5.5V range allows operation alongside common embedded security controllers, and the ±15kV IEC ESD protection supports connector reliability. Security designs should still authenticate commands at a higher protocol layer, isolate maintenance access, and avoid treating physical-layer protection as a substitute for secure device authentication.
Được đề xuất
Portable Diagnostic Connector
The MAX3221EIPW is appropriate for portable diagnostic equipment that needs a compact RS-232 service connector. Its 250kbps single-channel interface supports log transfers and configuration commands, and the 3V-to-5.5V supply range fits systems operating from either 3.3V or 5V rails. Because a detachable cable can expose the port to electrostatic discharge, the documented ±15kV IEC 61000-4-2 protection is an important selection criterion. Keep the four charge-pump capacitors close to the device, maintain separation between connector-side traces and internal logic, and validate the complete cable and enclosure configuration at the system level.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho MAX3221EIPW — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | MAX3221CPWR | MAX3221ECPWR | MAX3221IPWR |
|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | TSSOP-16 | TSSOP-16 | TSSOP-16 | TSSOP-16 |
| Product Type | Single-channel RS-232 line driver and receiver | Single-channel MAX3221 RS-232 transceiver | Single-channel MAX3221E RS-232 transceiver | Single-channel MAX3221 RS-232 transceiver |
| Number of Drivers | 1 driver | 1 driver | 1 driver | 1 driver |
| Number of Receivers | 1 receiver | 1 receiver | 1 receiver | 1 receiver |
| Supply Voltage Range | 3V to 5.5V | 3V to 5.5V | 3V to 5.5V | 3V to 5.5V |
| Maximum Data Rate | 250kbps | 250kbps | 250kbps | 250kbps |
| RS-232 Pin ESD Protection | ±15kV | ±15kV | ±15kV | ±15kV |
Bảo phân biệt quan trọng
- Single-channel RS-232 interface in a compact TSSOP-16 package (vsMAX3232EEAE+)
- Documented enhanced IEC ESD protection (vsMAX3221CPWR)
- Single-supply operation across 3.3V and 5V rails (vsMAX3221IPWR)
Ghi chú thiết kế
Place the four charge-pump capacitors directly beside their assigned pins and use the shortest practical ground return from each capacitor. Keep the connector-side driver and receiver nets away from UART, clock, and sensitive analog traces. Route the RS-232 signal and ground as a matched pair to reduce emissions and susceptibility to common-mode noise. Where the interface crosses a board boundary, place any supplementary protection network near the connector rather than near the transceiver.
Do not treat the RS-232 transceiver as a galvanic-isolated interface. Verify that the logic ground and cable-side ground follow the system’s intended topology, because an unintended ground connection can defeat isolation elsewhere in the design. Also confirm the required supply rail, charge-pump capacitor values, enable state, and connector gender before PCB release. A package match alone is not sufficient to approve MAX3221CPWR, MAX3221ECPWR, or MAX3221IPWR as a replacement.
RS-232 driver edges can radiate into nearby circuitry even when the data rate is modest. Maintain maximum practical separation between the driver output and receiver input from the transceiver to the connector, avoid routing the cable-side signal beneath sensitive circuitry, and provide a continuous ground reference beneath or adjacent to the route where practical. For long or unshielded cables, evaluate the completed system with the required EMC test setup rather than relying only on the ±15kV ESD rating.
Thông tin tuân thủ
The MAX3221E product content confirms IEC 61000-4-2 ESD protection and TIA/EIA-232-F interface compliance. RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals status were not explicitly established for the exact ordering code and remain unknown.