MAX3221EIPW - 250kbps Single RS-232 Transceiver | TI
MPN: MAX3221EIPW ✓ 啟用中MAX3221EIPW 概覽
An RS-232 transceiver is an interface IC that converts logic-level UART signals into differential, bipolar RS-232 levels and converts received RS-232 signals back into logic-compatible levels. The MAX3221E belongs to the RS-232 transceiver family within interface ICs and power-management-adjacent signal-conditioning devices. It provides the electrical interface between an asynchronous communication controller and a serial-port connector.
The MAX3221E uses a single power supply and an on-chip charge pump with four small external capacitors. Its single driver and single receiver arrangement suits point-to-point serial links, while the enhanced ESD protection helps improve robustness at connector-facing pins. Operation across a 3V to 5.5V supply range supports both 3.3V and 5V system rails.
The device meets TIA/EIA-232-F requirements and provides IEC 61000-4-2 ESD protection. These qualifications are important because RS-232 implementations frequently connect through external connectors where cables and ESD events can introduce transient voltage. The MAX3221EIPW is therefore suitable for industrial control links, service interfaces, and embedded equipment requiring a compact single-channel RS-232 solution.
Typical uses include configuring a UART port on an embedded controller, upgrading an industrial peripheral that still uses an RS-232 connector, and creating a service or debug link between a host computer and field equipment. Because the interface is single-channel, applications needing multiple simultaneous RS-232 ports generally require additional transceiver channels or separate interface devices.
Place the four charge-pump capacitors close to their assigned pins, and route the RS-232 driver and receiver traces as a protected cable-side interface. Keep logic-side UART traces away from connector and charge-pump nodes, provide a stable ground return, and verify the external protection network against the system’s ESD requirements.
This page combines the manufacturer’s electrical specifications, package details, qualified substitute analysis, and practical PCB guidance. It also highlights where MAX3221E family alternatives share the same TSSOP-16 footprint and where their shutdown, enable, or ESD characteristics require verification before replacement.
直接替換替代品,適用於 MAX3221EIPW — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: MAX3221EIPW (相同外形與佔位) — 差異在於 Product Type, Number of Drivers, Number of Receivers, Supply Voltage Range, Maximum Data Rate.
MAX3221CPWR
✅ 直接替換📋 參考替代品(不在目錄中)
MAX3221ECPWR
✅ 直接替換聯絡詢價
查看資料表 →MAX3221IPWR
✅ 直接替換聯絡詢價
查看資料表 →MAX3221EIPW 規格
| Product Type | Single-channel RS-232 line driver and receiver |
| Supply Voltage Range | 3V to 5.5V |
| Maximum Data Rate | 250kbps |
| Number of Drivers | 1 driver |
| Number of Receivers | 1 receiver |
| RS-232 ESD Protection | ±15kV |
| ESD Standard | IEC 61000-4-2 |
| RS-232 Standard Compliance | TIA/EIA-232-F |
| Charge-Pump Capacitors Required | 4 external capacitors |
| 封裝 | 16-pin TSSOP |
| 安裝類型 | Surface mount |
| 介面類型 | Full RS-232 transceiver |
| Driver and Receiver Count | 1/1 transceiver |
MAX3221EIPW 16-pin tssop 腳位配置指南
MAX3221EIPW(16-pin tssop 封裝)的腳位配置。 腳位編號、功能與連接圖定義於製造商資料手冊中。請參閱該手冊以取得確切的封裝尺寸與焊接指引。
無詳細腳位定義資料: MAX3221EIPW.
請參閱 資料表 以查看完整腳位配置。
典型應用
MAX3221EIPW 適用於 6 應用s: Industrial Control Console, Embedded UART-to-RS-232 Bridge, Point-to-Point Serial Link, Instrument Service Interface, Security and Access Controller, Portable Diagnostic Connector.
Industrial Control Console
The MAX3221EIPW is suitable for connecting an industrial controller or service terminal that still uses an RS-232 port. Its 3V-to-5.5V operating range permits use with 3.3V or 5V embedded systems, while the 250kbps data rate supports administrative commands, configuration transfers, and diagnostic traffic. The single driver and receiver provide the required levels between a UART controller and a DB9 or terminal connector. Its ±15kV IEC 61000-4-2 protection is particularly relevant where the cable is exposed to human contact. Designers should still include appropriate common-mode and surge protection for long industrial runs.
推薦
Embedded UART-to-RS-232 Bridge
The MAX3221EIPW bridges the logic-level UART pins of an embedded controller to a full RS-232 port. Its single 3V-to-5.5V supply simplifies integration with common embedded processors, while 250kbps operation is appropriate for configuration commands, firmware-console traffic, and short control exchanges. The internal charge pump needs only four external capacitors, reducing board area compared with a discrete driver-receiver implementation. A key layout consideration is to separate the cable-side RS-232 traces from sensitive UART and processor signals. Firmware should also account for RS-232 level inversion and ensure that the selected UART supports the required baud rate.
推薦
Point-to-Point Serial Link
The MAX3221EIPW provides one transmitter and one receiver for point-to-point communication between two asynchronous systems. At up to 250kbps, it is suitable for short control and monitoring links where a modern multi-protocol transceiver would add unnecessary cost or complexity. The single-supply architecture supports both 3.3V and 5V systems, and the charge-pump arrangement allows the interface to operate without a separate bipolar supply. When laying out the link, use a continuous signal and ground return, keep connector protection close to the entry point, and verify that the far-end UART receiver recognizes the bipolar RS-232 signaling correctly.
推薦
Instrument Service Interface
The MAX3221EIPW can provide a service port for laboratory, test, and measurement equipment that retains an RS-232 configuration interface. The 250kbps capability is more than adequate for command exchange, calibration files, and diagnostic logs, while the single TSSOP-16 package supports compact front-panel or board-level implementations. The ±15kV IEC ESD rating on the RS-232 pins adds protection at a connector that operators may contact frequently. For portable instruments, ensure the chassis and logic grounds follow the required RS-232 topology, and place any additional surge protection outside the logic-side routing area.
推薦
Security and Access Controller
The MAX3221EIPW can add an RS-232 maintenance channel to access-control or security equipment without consuming a dedicated multichannel interface IC. A 250kbps RS-232 link is suitable for configuration exchange, event-log retrieval, and controlled commissioning commands when the system already supports this legacy physical interface. The 3V-to-5.5V range allows operation alongside common embedded security controllers, and the ±15kV IEC ESD protection supports connector reliability. Security designs should still authenticate commands at a higher protocol layer, isolate maintenance access, and avoid treating physical-layer protection as a substitute for secure device authentication.
推薦
Portable Diagnostic Connector
The MAX3221EIPW is appropriate for portable diagnostic equipment that needs a compact RS-232 service connector. Its 250kbps single-channel interface supports log transfers and configuration commands, and the 3V-to-5.5V supply range fits systems operating from either 3.3V or 5V rails. Because a detachable cable can expose the port to electrostatic discharge, the documented ±15kV IEC 61000-4-2 protection is an important selection criterion. Keep the four charge-pump capacitors close to the device, maintain separation between connector-side traces and internal logic, and validate the complete cable and enclosure configuration at the system level.
推薦
推薦產品摘要
工程參考資料,適用於 MAX3221EIPW — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | MAX3221CPWR | MAX3221ECPWR | MAX3221IPWR |
|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | TSSOP-16 | TSSOP-16 | TSSOP-16 | TSSOP-16 |
| Product Type | Single-channel RS-232 line driver and receiver | Single-channel MAX3221 RS-232 transceiver | Single-channel MAX3221E RS-232 transceiver | Single-channel MAX3221 RS-232 transceiver |
| Number of Drivers | 1 driver | 1 driver | 1 driver | 1 driver |
| Number of Receivers | 1 receiver | 1 receiver | 1 receiver | 1 receiver |
| Supply Voltage Range | 3V to 5.5V | 3V to 5.5V | 3V to 5.5V | 3V to 5.5V |
| Maximum Data Rate | 250kbps | 250kbps | 250kbps | 250kbps |
| RS-232 Pin ESD Protection | ±15kV | ±15kV | ±15kV | ±15kV |
主要差異化特點
- Single-channel RS-232 interface in a compact TSSOP-16 package (對比MAX3232EEAE+)
- Documented enhanced IEC ESD protection (對比MAX3221CPWR)
- Single-supply operation across 3.3V and 5V rails (對比MAX3221IPWR)
設計說明
Place the four charge-pump capacitors directly beside their assigned pins and use the shortest practical ground return from each capacitor. Keep the connector-side driver and receiver nets away from UART, clock, and sensitive analog traces. Route the RS-232 signal and ground as a matched pair to reduce emissions and susceptibility to common-mode noise. Where the interface crosses a board boundary, place any supplementary protection network near the connector rather than near the transceiver.
Do not treat the RS-232 transceiver as a galvanic-isolated interface. Verify that the logic ground and cable-side ground follow the system’s intended topology, because an unintended ground connection can defeat isolation elsewhere in the design. Also confirm the required supply rail, charge-pump capacitor values, enable state, and connector gender before PCB release. A package match alone is not sufficient to approve MAX3221CPWR, MAX3221ECPWR, or MAX3221IPWR as a replacement.
RS-232 driver edges can radiate into nearby circuitry even when the data rate is modest. Maintain maximum practical separation between the driver output and receiver input from the transceiver to the connector, avoid routing the cable-side signal beneath sensitive circuitry, and provide a continuous ground reference beneath or adjacent to the route where practical. For long or unshielded cables, evaluate the completed system with the required EMC test setup rather than relying only on the ±15kV ESD rating.
合規資訊
The MAX3221E product content confirms IEC 61000-4-2 ESD protection and TIA/EIA-232-F interface compliance. RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals status were not explicitly established for the exact ordering code and remain unknown.