MAX3232CDG4 - 3V Dual RS-232 Transceiver | Texas Instruments
MPN: MAX3232CDG4 ✓ Hoạt độngMAX3232CDG4 Tóm tắt
An RS-232 transceiver is an interface IC that converts between digital logic-level signals and the bipolar voltage levels used by RS-232 equipment. This device sits between a UART, microcontroller, or other host controller and a serial connector. Within the semiconductor hierarchy, the MAX3232CDG4 is an interface IC, a line transceiver, and a dual charge-pump RS-232 transceiver designed for reliable point-to-point serial links.
Key features include two transmit channels, two receive channels, low-power operation, a maximum data rate of 250 kbit/s, and a single 3 V to 5.5 V supply. Four external 0.1 µF capacitors support the charge-pump and supply functions. The 16-SOIC package is suitable for conventional surface-mount PCB assembly, while the C-grade version is intended for commercial-temperature operation from 0 °C to 70 °C.
The MAX3232 family includes the MAX3232E, which Texas Instruments describes as an improved direct drop-in replacement for the original MAX3232. The E variant offers a useful upgrade path for new designs, but engineers must verify the complete pinout, electrical limits, capacitor requirements, and operating-temperature range of the exact orderable suffix before replacing a populated board.
Typical uses include industrial serial consoles, point-of-sale equipment, data-acquisition controllers, instrumentation, and legacy peripheral interfaces that use an RS-232 port but operate from a modern 3.3 V or 5 V logic supply. The transceiver is especially useful where a UART needs true RS-232 electrical levels rather than TTL-level signaling.
For layout, place the required charge-pump capacitors close to their associated pins and route the RS-232 driver outputs and receiver inputs away from sensitive clock, reset, and analog signals. Confirm that the host UART logic voltage matches the receiver threshold and driver interface requirements. A common mistake is treating RS-232 as a differential or ground-referenced logic standard; it uses a single-ended bipolar signal referenced to the common ground connection.
This product page combines manufacturer specifications, package details, lifecycle considerations, drop-in alternatives, and application-specific design guidance. It supports faster component selection while keeping the electrical and mechanical checks needed for a safe PCB substitution.
Bộ thay thế dễ dàng lắp đặt cho MAX3232CDG4 — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với MAX3232CDG4 (cùng hình factor và footprint) — khác nhau ở ESD Protection, Package.
MAX3232CDE4
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →MAX3232EIDWR
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
MAX3232ID
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →MAX3232ECDR
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →MAX3232ECWE
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
SN65C3232D
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
MAX3232CDG4 Thông số kỹ thuật
| Device Type | 2/2 RS-232 line transceiver |
| Number of Drivers | 2 |
| Number of Receivers | 2 |
| Supply Voltage Range | 3 V to 5.5 V |
| Maximum Data Rate | 250 kbit/s |
| ESD Protection | ±15 kV using the human-body model |
| Interface Standard | TIA/EIA-232-F and ITU V.28 |
| Khoảng nhiệt độ hoạt động | 0 °C to 70 °C |
| Hộp | 16-SOIC, 3.90 mm width |
| Kiểu lắp đặt | Surface mount |
| External Capacitors | 4 × 0.1 µF |
| Supply Type | Single supply |
| Charge-Pump Architecture | Integrated dual charge pump |
| Logic Compatibility | 3.3 V and 5 V CMOS logic |
| Packaging | Tube |
| Lead-Free Status | Lead free |
Hướng dẫn cấu hình chân MAX3232CDG4 16-soic, 3.90 mm width
Cấu hình chân cho MAX3232CDG4 (16-soic, 3.90 mm width gói). Số thứ tự chân, chức năng và sơ đồ kết nối được xác định trong tài liệu thông số kỹ thuật của nhà sản xuất. Tham khảo nó để biết footprint và hướng dẫn hàn chính xác.
Không có dữ liệu chân cụ thể sẵn có cho MAX3232CDG4.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
MAX3232CDG4 phù hợp cho 6 Áp dụngs: Industrial Serial Consoles, Point-of-Sale Terminals, Data-Acquisition Instruments, Legacy Peripheral Connectivity, Network Equipment Management, Automated Test Equipment.
Industrial Serial Consoles
The MAX3232CDG4 fits industrial console and service-port designs that require a modern 3.3 V or 5 V host controller to communicate through a true RS-232 port. Its two drivers and two receivers support full-duplex serial links, while the 250 kbit/s maximum rate exceeds common console baud rates. The integrated charge pump reduces the number of external active components, although four 0.1 µF capacitors are still required. Place the capacitors close to their associated pins, connect the interface ground to the host ground, and route the bipolar driver outputs away from sensitive logic. The 0 °C to 70 °C operating range suits controlled indoor equipment, but outdoor machinery may require a wider-temperature alternative.
Được đề xuất
Point-of-Sale Terminals
Point-of-sale equipment often combines a low-voltage application processor with legacy peripherals that expose RS-232 connections. The MAX3232CDG4 provides the electrical conversion needed between host-side CMOS logic and bipolar RS-232 signals. Two transmit and two receive channels are useful for paired service, printer, or peripheral links, and the 250 kbit/s capability provides ample margin for typical serial transactions. Its 3 V to 5.5 V operating range aligns with common embedded and industrial computing platforms. Designers should verify the UART signal levels, provide a reliable common ground, and keep charge-pump nodes and switching-capacitor current away from sensitive display, touchscreen, and communication circuitry.
Được đề xuất
Data-Acquisition Instruments
The MAX3232CDG4 can serve as the RS-232 interface for laboratory instruments, factory test equipment, and compact data-acquisition controllers. The device bridges a UART or microcontroller to a conventional RS-232 port at rates up to 250 kbit/s, allowing legacy host computers or test systems to exchange commands and measurement data. Its integrated charge-pump circuitry simplifies the physical interface compared with a discrete bipolar driver implementation. For reliable measurements, isolate noisy relay, motor, or actuator wiring from the transceiver, use a short ground-reference path, and confirm that external protection devices do not distort the receiver thresholds or driver rise and fall behavior.
Được đề xuất
Legacy Peripheral Connectivity
MAX3232CDG4 is useful when an embedded controller must maintain compatibility with legacy RS-232 printers, scanners, programmers, or service adapters. The two-channel architecture supports simultaneous transmit and receive paths, and the single 3 V to 5.5 V supply simplifies integration with modern digital systems. Its ±15 kV human-body-model ESD rating improves robustness at accessible connector points, although board-level protection and cable practices remain important. The design should account for the voltage reference of RS-232, which is ground-referenced and single-ended rather than differential. Confirm the pin mapping, connector protection, and UART baud-rate tolerance for every peripheral before releasing the PCB.
Được đề xuất
Network Equipment Management
The MAX3232CDG4 can provide a dedicated management or console interface for network appliances, gateways, and communications equipment. A low-power management processor can use the transceiver to connect an RS-232 service port to configuration equipment or a legacy management system. The 250 kbit/s signaling capability is more than sufficient for command traffic, while the 3 V to 5.5 V supply range supports embedded system rails. Place the interface near its connector, maintain a low-impedance common-ground connection, and separate the switching charge-pump region from clock-sensitive circuitry. The commercial-temperature version is appropriate where the enclosure remains within 0 °C to 70 °C.
Được đề xuất
Automated Test Equipment
The MAX3232CDG4 is appropriate for automated test equipment requiring a compact host-to-fixture RS-232 control path. Its dual drivers and receivers permit bidirectional command and status communication between a controller and legacy test hardware. The integrated charge pump provides the required bipolar interface from a 3.3 V or 5 V supply, and the 250 kbit/s rate supports common test-control protocols. Designers should establish one solid interface ground, protect the connector against cable transients, and route the RS-232 nets separately from high-voltage switching nodes. Because the C-grade device is rated from 0 °C to 70 °C, production test-floor temperature extremes may justify selecting an industrial-temperature alternative.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho MAX3232CDG4 — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | MAX3232CDE4 | MAX3232EIDWR | MAX3232ID | MAX3232ECDR | MAX3232ECWE | SN65C3232D |
|---|---|---|---|---|---|---|---|
| Package | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Device Type | 2/2 RS-232 transceiver | MAX3232C RS-232 transceiver | MAX3232E RS-232 transceiver | MAX3232 RS-232 transceiver | MAX3232E RS-232 transceiver | MAX3232E RS-232 transceiver | 2-channel RS-232 transceiver |
| Generation | MAX3232C | MAX3232C | MAX3232E improved generation | MAX3232 | MAX3232E improved generation | MAX3232E improved generation | SN65C3232D |
Bảo phân biệt quan trọng
- Original MAX3232C feature set with two full-duplex channels (vsSN65C3232D)
- Direct path to the manufacturer's improved MAX3232E generation (vsMAX3232EIDWR)
- Commercial-temperature MAX3232C configuration in a standard 16-SOIC package (vsMAX3232EIDWR)
Ghi chú thiết kế
Place the four required 0.1 µF charge-pump and supply capacitors close to the pins identified in the manufacturer pin-description diagram. Keep each capacitor’s return path short and avoid routing the associated switching node beneath sensitive analog or high-speed digital traces. A common layout error is to place capacitors only near the IC while allowing long connections to the charge-pump reservoir nodes, which can increase ringing and reduce margin.
Separate the bipolar RS-232 driver outputs and receiver inputs from clocks, resets, ADC inputs, and other sensitive nets. RS-232 is a single-ended, ground-referenced interface, so connect the transceiver and host grounds through a low-impedance path. Do not treat the interface as differential; use the connector and cable ground as the signal reference, and avoid sharing narrow ground paths with motor, relay, or switching-power currents.
Confirm the MAX3232CDG4 16-SOIC pin mapping and the exact ordering suffix before substituting a MAX3232E or SN65C3232D device. Check supply range, UART logic compatibility, operating temperature, ESD rating, driver slew behavior, receiver thresholds, and capacitor connections. Even when all parts use a 16-SOIC outline, a shared body size does not by itself prove that every pin can be replaced without review.
Thông tin tuân thủ
The component is identified as lead free. RoHS, REACH, halogen-free, and conflict-minerals statuses were not explicitly established by the cited product information.