MAX3232CPWE4 2/2 RS-232 Transceiver, 16-TSSOP | Texas Instruments
MPN: MAX3232CPWE4 ✓ Hoạt độngMAX3232CPWE4 Tóm tắt
An RS-232 transceiver is an interface IC that bridges logic-level signals and the voltage ranges used by RS-232 links. The line-driver section converts low-voltage logic signals into RS-232 levels, while the receiver section converts incoming RS-232 signals into CMOS-compatible logic. Within the broader hierarchy, this device is a physical-layer interface IC, a multichannel line transceiver, and a semiconductor for data communications and industrial-control equipment.
The main operating characteristics are a 3 V to 5.5 V single-supply range, two drivers, two receivers, and data rates up to 250 kbit/s. The manufacturer datasheet also identifies ±15 kV human-body-model ESD protection. These characteristics make the device useful where legacy RS-232 equipment must coexist with low-voltage UART, microcontrollers, industrial controllers, and service equipment.
The MAX3232 architecture supports operation from a supply as low as 3 V without requiring a separate 12 V RS-232 supply. Internal charge-pump circuitry develops the bipolar voltage needed by the drivers, while the receiver inputs include ESD protection. This integration simplifies board design while retaining the signaling behavior required by TIA/EIA-232-F and ITU V.28 applications described for the device.
Typical uses include service-console connections, configuration interfaces on industrial equipment, point-of-sale terminals, security systems, and instrumentation. Two channels can support simultaneous transmit and receive activity, while dual receiver channels are useful for systems requiring one transmit line and two receive lines or a second unidirectional channel.
When laying out the circuit, keep charge-pump and interface-capacitor connections short, provide the required supply and bypass capacitance, and route connector-side signals away from sensitive logic. Confirm pin availability, input and output logic levels, and RS-232 lead lengths against the manufacturer pin-description table before finalizing a PCB footprint.
This product page combines the exact ordering information, electrical limits, package data, qualified alternatives, comparison parameters, and practical interface-layout guidance needed to evaluate the MAX3232CPWE4 as a drop-in candidate for an existing 16-pin TSSOP design.
Bộ thay thế dễ dàng lắp đặt cho MAX3232CPWE4 — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với MAX3232CPWE4 (cùng hình factor và footprint) — khác nhau ở Maximum Data Rate, Package, Supply Voltage Range.
MAX3232IPWR
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →MAX3232CUE+
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →MAX3232CWEY
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
MAX3232CWEZ
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
ICL3232EIV-16Z
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
MAX3232CPWE4 Thông số kỹ thuật
| Product Type | 2/2 RS-232 line transceiver |
| Number of Drivers | 2 |
| Number of Receivers | 2 |
| Supply Voltage Range | 3 V to 5.5 V |
| Maximum Data Rate | 250 kbit/s |
| Interface Standard | RS-232 |
| ESD Protection | ±15 kV using the human-body model |
| Hộp | 16-TSSOP, 0.173 in / 4.40 mm width |
| Number of Terminals | 16 |
| Kiểu lắp đặt | Surface mount |
| Terminal Form | Gull wing |
| Package Shape | Rectangular |
| Temperature Grade | Commercial |
| Packaging | Tube |
| Standards Compliance | TIA/EIA-232-F and ITU V.28 |
Hướng dẫn cấu hình chân MAX3232CPWE4 rectangular
Cấu hình chân cho MAX3232CPWE4 (rectangular gói). Số thứ tự chân, chức năng và sơ đồ kết nối được xác định trong tài liệu thông số kỹ thuật của nhà sản xuất. Tham khảo nó để biết footprint và hướng dẫn hàn chính xác.
Không có dữ liệu chân cụ thể sẵn có cho MAX3232CPWE4.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
MAX3232CPWE4 phù hợp cho 6 Áp dụngs: Industrial Configuration Port, Serial Service Console, Point-of-Sale Terminal, Security and Access-Control Equipment, Test and Measurement Instrument, Building Access and Lighting Controller.
Industrial Configuration Port
The MAX3232CPWE4 fits a compact industrial configuration interface because it combines two drivers and two receivers while operating from 3 V to 5.5 V. It supports asynchronous links up to 250 kbit/s, allowing the controller to exchange commands with a service terminal through an RS-232 connector. Its ±15 kV human-body-model ESD protection is valuable on connector-facing equipment. Keep the interface and charge-pump capacitors close to the device, and verify that the industrial temperature range and grounding strategy meet the enclosure’s requirements.
Được đề xuất
Serial Service Console
A MAX3232CPWE4 can bridge a low-voltage controller UART to a legacy RS-232 service port without a separate 12 V supply. The 3 V minimum supply supports modern embedded systems, while the 250 kbit/s capability exceeds the throughput of most configuration consoles. Two drivers and two receivers also permit separate command and diagnostic paths where wiring permits. Use short connector-side traces, a solid ground reference, and protection appropriate to the exposed port environment.
Được đề xuất
Point-of-Sale Terminal
The MAX3232CPWE4 is appropriate for a point-of-sale terminal that retains an RS-232 peripheral interface. A 3 V to 5.5 V operating range allows the interface to share power with efficient embedded logic, and 250 kbit/s supports legacy serial scanners, receipt devices, or customer displays. The integrated 2/2 channel arrangement reduces external driver count. Confirm logic polarity and connector pin assignment against the peripheral manual, and place ESD protection and bypass capacitance near their respective connections.
Được đề xuất
Security and Access-Control Equipment
A MAX3232CPWE4 can provide the legacy RS-232 link used by access-control panels, card readers, or alarm interfaces during installation and maintenance. The device’s low-voltage operation suits controller boards based on modern mixed-signal processors, and its ESD protection helps reduce risk at an externally accessible connector. The 16-TSSOP package supports compact board layouts, while two drivers and two receivers provide flexible point-to-point connectivity. Validate the ground reference, cable length, and surge requirements for the installation environment.
Được đề xuất
Test and Measurement Instrument
The MAX3232CPWE4 is useful in test and measurement equipment that accepts legacy RS-232 commands from a host computer. Its 250 kbit/s maximum rate is suitable for ordinary asynchronous instrument-control traffic, and operation from 3 V to 5.5 V simplifies integration with low-voltage control hardware. Two channels can serve separate receive and status lines. Route the RS-232 traces away from sensitive analog sections, preserve the recommended bypass network, and verify receiver thresholds for the connected test system.
Được đề xuất
Building Access and Lighting Controller
The MAX3232CPWE4 can support RS-232 commissioning or supervisory links in building-access and lighting-control modules. The 3 V to 5.5 V supply range fits low-energy embedded controllers, and the 250 kbit/s limit is more than sufficient for configuration traffic. Two receiver channels can monitor equipment status or accept inputs from multiple unidirectional sources. Keep the interface ground close to the transceiver ground, avoid long parallel routes next to switching circuitry, and verify all numbered pins before adapting an existing 16-TSSOP board.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho MAX3232CPWE4 — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | MAX3232IPWR | MAX3232CUE+ | MAX3232CWEY | MAX3232CWEZ | ICL3232EIV-16Z |
|---|---|---|---|---|---|---|
| Package | 16-TSSOP | 16-TSSOP | 16-TSSOP | 16-TSSOP | 16-TSSOP | 16-TSSOP |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Renesas Electronics |
| Transceiver Configuration | 2/2 full RS-232 transceiver | 2/2 RS-232 transceiver | 2/2 MAX3232-family transceiver | 2/2 MAX3232-family transceiver | 2/2 MAX3232-family transceiver | 2/2 RS-232 transceiver |
Bảo phân biệt quan trọng
- Two integrated drivers and receivers (vsMAX3232IPWR)
- Single-supply RS-232 operation (vsICL3232EIV-16Z)
- Connector-facing ESD protection (vsMAX3232CUE+)
Ghi chú thiết kế
Place the charge-pump capacitors and supply bypass capacitors close to their numbered IC pins, following the manufacturer’s typical application circuit. Keep connector-side driver and receiver traces short, provide a continuous ground reference, and avoid routing them beneath switching nodes or noisy clock lines. The 16-TSSOP footprint leaves little room for long point-to-point connections, so assign the external network before placing the connector.
RS-232 links are point-to-point interfaces, and the 250 kbit/s rating should not be treated as a guarantee for arbitrary cable lengths. Match the line impedance with the selected transceiver, maintain a suitable ground reference, and avoid excessive stub lengths. When replacing the MAX3232CPWE4, verify receiver enable levels, driver polarity, input thresholds, and charge-pump capacitor values rather than relying on the 16-pin package alone.
Do not substitute solely by package outline or driver count. The suffix can define temperature grade, reel or tube packing, and ordering options. Before approving MAX3232IPWR, MAX3232CUE+, or ICL3232EIV-16Z, compare every numbered pin, supply limits, receiver enable behavior, ESD rating, maximum data rate, and external capacitor requirements against the original design.
The MAX3232’s internal charge-pump circuitry can couple energy into surrounding traces if the capacitor network is not placed carefully. Use the shortest permitted capacitor connections, place input and output bypass components near the device, and maintain separation between RS-232 connector paths and sensitive analog or high-speed digital nets. A common ground plane and controlled return-current path are important when the interface cable leaves the enclosure.
Thông tin tuân thủ
The manufacturer datasheet information identifies ±15 kV human-body-model ESD protection and TIA/EIA-232-F and ITU V.28 compliance. No explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declaration was present in the cited product records.