MAX3232CPWG4 - 2/2 RS-232 Transceiver, 3-5.5V | TI
MPN: MAX3232CPWG4 ✓ Hoạt độngMAX3232CPWG4 Tóm tắt
An RS-232 transceiver is an interface IC that converts logic-level UART signals into RS-232-compatible line levels and converts incoming RS-232 signals back into logic levels. It belongs to the interface IC hierarchy and is commonly placed between a host UART connector and an external data-processing or communications device. The MAX3232 family supports both 3.3 V and 5 V system rails, making it useful in industrial controllers, embedded systems, test equipment, and legacy serial-port designs.
Key features include two RS-232 drivers, two RS-232 receivers, a 3 V to 5.5 V supply range, operation up to 250 kbit/s, and ±15 kV ESD protection on the serial-port connections. The 16-pin TSSOP package reduces board area compared with larger SOIC options, while the integrated charge pump eliminates the need for a separate RS-232 line-voltage supply. Four external 0.1 µF charge-pump capacitors are required for normal operation.
Technically, the MAX3232CPWG4 combines a dual charge-pump circuit with push-pull line drivers and receiver inputs. The charge pump develops positive and negative rails internally, allowing the drivers to produce compliant RS-232 levels from a single low-voltage supply. The receiver stage supports reliable detection of the RS-232 logic states, while the transceiver architecture supports both transmit and receive paths on the same device.
Typical applications include industrial serial adapters, embedded instrumentation, programmable-logic-controller interfaces, barcode and label equipment, board-to-board serial links, and test or measurement systems that retain an RS-232 port. In these systems, the device provides level translation while reducing the number of external power rails and supporting compact, high-speed serial communication.
For PCB design, place the four 0.1 µF charge-pump capacitors close to their associated C1+, C1−, C2+, and C2− pins, and route the RS-232 connector signals with return-path awareness. Because ESD events occur at externally accessible connectors, maintain a short ground path and consider additional board-level protection when cables are long or the equipment is used in severe industrial environments.
This product page combines the manufacturer's device data with practical application guidance, package information, replacement analysis, and design notes. It is intended to help engineers evaluate the MAX3232CPWG4 quickly while preserving the electrical and layout checks required for a dependable RS-232 interface.
Bộ thay thế dễ dàng lắp đặt cho MAX3232CPWG4 — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với MAX3232CPWG4 (cùng hình factor và footprint) — khác nhau ở Package, Supply Voltage Range, Maximum Data Rate, External Charge-Pump Capacitors, Number of Receivers.
MAX3232IPW
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →MAX3232EIPWG4
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →MAX3232EUE+
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →MAX3232CUE+
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →MAX3232CPWR
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →MAX3232CPWG4 Thông số kỹ thuật
| Transceiver Configuration | 2 drivers and 2 receivers |
| Supply Voltage Range | 3 V to 5.5 V |
| Maximum Data Rate | 250 kbit/s |
| Interface Standard | RS-232 |
| ESD Protection | ±15 kV |
| Hộp | 16-pin TSSOP, 4.40 mm width |
| Kiểu lắp đặt | Surface Mount |
| External Charge-Pump Capacitors | 4 capacitors, 0.1 µF each |
| Supply Compatibility | 3 V and 5 V supply operation |
| Driver Count | 2 |
| Receiver Count | 2 |
| Transceiver Type | Multichannel line driver and receiver |
| Technology Standards | TIA/EIA-232-F and ITU V.28 |
| ESD Test Model | Human-Body Model, ±15 kV |
Cấu hình chân MAX3232CPWG4
| Chân 1 | R1OUT — Receiver 1 output |
| Chân 2 | R1IN — Receiver 1 input |
| Chân 3 | R2IN — Receiver 2 input |
| Chân 4 | R2OUT — Receiver 2 output |
| Chân 5 | T1IN — Driver 1 logic input |
| Chân 6 | T1OUT — Driver 1 RS-232 output |
| Chân 7 | T2OUT — Driver 2 RS-232 output |
| Chân 8 | T2IN — Driver 2 logic input |
| Chân 9 | GND — Ground |
| Chân 10 | VCC — Positive supply input |
| Chân 11 | C1+ — Charge-pump capacitor 1 positive terminal |
| Chân 12 | C1- — Charge-pump capacitor 1 negative terminal |
| Chân 13 | C2+ — Charge-pump capacitor 2 positive terminal |
| Chân 14 | C2- — Charge-pump capacitor 2 negative terminal |
| Chân 15 | V- — Negative charge-pump output |
| Chân 16 | V+ — Positive charge-pump output |
Ứng dụng tiêu biểu
MAX3232CPWG4 phù hợp cho 6 Áp dụngs: Industrial Serial Adapter, Programmable Logic Controller Interface, Test and Measurement Equipment, Barcode and Label Equipment, Board-to-Board Serial Link, Embedded Diagnostic Port.
Industrial Serial Adapter
The MAX3232CPWG4 fits an industrial serial adapter that converts a 3.3 V or 5 V UART into an RS-232 port. Its two transmitters and two receivers support bidirectional serial communication, while the 3 V to 5.5 V supply range permits integration with both embedded processor families. The 250 kbit/s maximum data rate covers legacy equipment and supervisory protocols that remain below that limit. Four 0.1 µF charge-pump capacitors generate the required bipolar driver voltages, while ±15 kV ESD protection strengthens the externally accessible connector interface.
Được đề xuất
Programmable Logic Controller Interface
The MAX3232CPWG4 is appropriate for a programmable logic controller or embedded controller that must retain an RS-232 service or programming port. Its 2/2 arrangement allows two connections without sharing a driver, and operation from 3 V to 5.5 V supports industrial logic levels that may differ from the legacy RS-232 side. The 16-pin TSSOP footprint preserves PCB area compared with larger packages. Designers should route the charge-pump network close to the IC and provide a low-impedance ground connection at the serial connector to improve return-path behavior.
Được đề xuất
Test and Measurement Equipment
The MAX3232CPWG4 can provide a compact RS-232 control port in test and measurement equipment, including legacy analyzers, programmable fixtures, and laboratory interfaces. Its 250 kbit/s capability supports many serial-control protocols, while the 2/2 channel count allows separate command and response paths. The 3 V to 5.5 V operating range allows the transceiver to share power with modern test-controller hardware. The ±15 kV HBM-rated protection is useful when the port is connected to a cable, although cable transients may justify additional surge protection outside the IC.
Được đề xuất
Barcode and Label Equipment
The MAX3232CPWG4 suits barcode scanners, label printers, and handheld equipment that communicate with a host through RS-232. The 2/2 transceiver architecture supports bidirectional command and data exchange, and the 250 kbit/s rate is suitable for typical point-to-point scanner traffic. A 3.3 V system can power the transceiver directly within its 3 V to 5.5 V range, simplifying power design. Keep the serial traces away from switching nodes and place the four charge-pump capacitors directly beside their associated pins to minimize charge-pump disturbance.
Được đề xuất
Board-to-Board Serial Link
The MAX3232CPWG4 is usable on a board-to-board cable link when legacy RS-232 levels and distance make the logic-level UART unsuitable. Its two transmit and two receive paths support a full-duplex interface, while the dual charge pump creates the positive and negative voltages required by the drivers from one 3 V to 5.5 V supply. The 16-pin TSSOP package suits compact control boards. For reliable operation, provide a common ground reference, maintain compatible logic levels on the UART side, and avoid relying on the transceiver's ESD rating as a substitute for a complete enclosure-level protection strategy.
Được đề xuất
Embedded Diagnostic Port
The MAX3232CPWG4 fits an embedded diagnostic or service port that provides access to a controller during development, manufacturing, or field maintenance. The 2/2 configuration supports dedicated transmit and receive signals, and the 3 V to 5.5 V range permits use with both 3.3 V and 5 V embedded processors. At 250 kbit/s, the interface can carry command output, diagnostic responses, and firmware-download traffic where the host software supports that rate. The exposed connector should have a nearby chassis or signal-ground reference, and the PCB should avoid long unprotected stubs between the connector and ESD-protected transceiver pins.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho MAX3232CPWG4 — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | MAX3232IPW | MAX3232EIPW | MAX3232EUE+ | MAX3232CUE+ | MAX3232CPW |
|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 16-pin TSSOP | 16-pin TSSOP | 16-pin TSSOP | 16-pin TSSOP | 16-pin TSSOP | 16-pin TSSOP |
| Transceiver Configuration | 2 drivers / 2 receivers | 2 drivers / 2 receivers | 2 drivers / 2 receivers | 2 drivers / 2 receivers | 2 drivers / 2 receivers | 2 drivers / 2 receivers |
| Supply Voltage Range | 3 V to 5.5 V | 3 V to 5.5 V | 3 V to 5.5 V | 3 V to 5.5 V | 3 V to 5.5 V | 3 V to 5.5 V |
| Mounting Type | Surface Mount | Surface Mount | Surface Mount | Surface Mount | Surface Mount | Surface Mount |
Bảo phân biệt quan trọng
- Direct 16-pin TSSOP integration (vsMAX3232EUE+)
- Three-rail compatibility for embedded systems (vsMAX3232IPW)
- Defined ESD performance for connector interfaces (vsMAX3232CUE+)
Ghi chú thiết kế
Place the four 0.1 µF charge-pump capacitors immediately adjacent to C1+, C1−, C2+, and C2−. Keep the loop formed by each capacitor and its associated device pin as small as practical. Use short ground and supply connections, avoid placing test pads between the capacitors and IC pins, and follow the charge-pump layout in the manufacturer datasheet. This is especially important in compact TSSOP layouts where switching currents can couple into adjacent UART and connector routes.
Route RS-232 driver outputs directly toward the connector and keep receiver inputs away from noisy switching nodes and the charge-pump capacitor area. Maintain a continuous ground reference between the transceiver ground and the connector ground. If the cable is externally accessible, avoid long unprotected traces between the connector and the MAX3232CPWG4, and provide chassis grounding or additional protection according to the enclosure's surge and ESD requirements.
Do not treat every MAX3232 suffix as electrically or commercially identical. Confirm that the exact replacement uses the 16-pin TSSOP footprint, supports the intended 3 V or 5 V supply, provides two drivers and two receivers, and meets the required ESD and temperature conditions. Also verify the shipping format, because an electrically compatible IC in a tube may not be acceptable to an automated production line configured for tape-and-reel presentation.
Thông tin tuân thủ
The device is an industrial RS-232 interface IC, so AEC-Q100 is not applicable. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status require confirmation from the current manufacturer product documentation.