MK10DX32VMP5 - 50MHz Cortex-M4 32KB MCU | NXP | 64-MAPBGA
MPN: MK10DX32VMP5 ✓ Hoạt độngMK10DX32VMP5 Tóm tắt
A microcontroller is a programmable semiconductor system that combines a CPU core, memory, communication interfaces, timers, analog functions, and control peripherals on one integrated circuit. The MK10DX32VMP5 belongs to the ARM Cortex-M4 microcontroller family, commonly used in embedded control, motor-control, communications, and industrial systems. Its 32-bit architecture and 50 MHz operating frequency provide a practical balance between processing capability, power consumption, and integration.
Key verified features include a 50 MHz ARM Cortex-M4 core, 32 KB (32K x 8) Flash program memory, 8 KB SRAM, and a 5 x 5 mm 64-MAPBGA package. The available interface set includes I2C, SPI, UART/USART, IrDA, I2S, DMA, PWM, a watchdog timer, low-voltage detection, and power-on reset. The 44 I/O count provides connection flexibility for sensors, actuators, communications, and human-interface circuitry in compact embedded products.
The Kinetis K10 family provides a scalable entry point into the Kinetis portfolio while integrating analog, communication, timing, and control peripherals. This makes the device suitable for applications that need broad peripheral support without moving to a larger package or higher-performance MCU. Exact operating voltage, temperature range, pin assignments, flash endurance, and detailed electrical limits were not included in the supplied verified snippets and must be confirmed from the official NXP datasheet before design release.
Typical uses include low-cost industrial controllers, compact sensor nodes, communication modules, motor and motion-control subsystems, and low-power embedded products. The 64-MAPBGA footprint is especially useful where PCB area is constrained, although its fine pitch requires careful assembly and inspection processes. Designers should confirm the exact package pinout, exposed-pad requirements, power architecture, decoupling recommendations, and software support using NXP documentation.
For replacement or second sourcing, compare the complete NXP ordering information, package drawing, pin multiplexing, memory size, clock configuration, peripheral set, and software migration requirements. A part with a similar listed processor or package may not be pin-compatible or functionally equivalent. This page combines verified distributor snippets with explicit data gaps rather than estimating unavailable electrical specifications.
Bộ thay thế dễ dàng lắp đặt cho MK10DX32VMP5 — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với MK10DX32VMP5 (cùng hình factor và footprint) — khác nhau ở Package, Mounting Type, Connectivity, Maximum Clock Frequency, Product Type.
MK20DX32VMP5
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
MK20DN32VMP5
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
MK10DX128VMP5
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
MK21FN1M0VLQ12
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →MK22FN128VMP10
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →MK10DX32VMP5 Tỷ lệ tối đa & tính chất điện
| Product Type | 32-bit ARM Cortex-M4 Kinetis K10 microcontroller |
| Core Processor | ARM Cortex-M4 |
| Tần số xung maksimum | 50 MHz |
| Flash Memory | 32 KB (32K x 8) |
| SRAM | 8 KB |
| Architecture | 32-bit RISC |
| Hộp | 64-MAPBGA, 5 x 5 mm |
| Number of I/O Pins | 44 I/O |
| Connectivity | I2C, IrDA, SPI, UART/USART |
| Peripheral Support | DMA, I2S, LVD, POR, PWM, WDT |
| Operating Feature Class | Baseline, low-power Kinetis MCU |
| Trạng thái vòng đời | Active |
| Kiểu lắp đặt | Surface-mount BGA |
| Package Ball Count | 64 balls |
Hướng dẫn cấu hình chân MK10DX32VMP5 64 balls
Cấu hình chân cho MK10DX32VMP5 (64 balls gói). IC số này bao gồm chân GPIO, giao diện truyền thông (UART, SPI, I2C) và chân nguồn. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết các chức năng chân thay thế và tùy chọn cấu hình. Cực kỳ quan trọng cho thiết kế hệ thống tích hợp và lập trình PCB.
Không có dữ liệu chân cụ thể sẵn có cho MK10DX32VMP5.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
MK10DX32VMP5 phù hợp cho 6 Áp dụngs: Compact Industrial Control, Sensor and IoT Node, Communication Module, Motor and Motion Control, Low-Power Embedded Product, Audio and Digital Interface.
Compact Industrial Control
The MK10DX32VMP5 fits compact control boards that need a 50 MHz Cortex-M4 core without the memory footprint of a larger MCU. Its verified 32 KB Flash and 8 KB SRAM are suitable for supervisory logic, state machines, parameter handling, and moderate peripheral coordination. UART/USART and I2C can connect local sensors or service interfaces, while PWM and watchdog functions support actuator monitoring and system recovery. The 44 I/O pins provide useful connectivity in a 5 x 5 mm 64-MAPBGA package, although the exact ball assignment and electrical limits must be verified before PCB release.
Được đề xuất
Sensor and IoT Node
The MK10DX32VMP5 is a practical fit for small sensor nodes that must combine local processing with serial connectivity. The verified I2C and SPI interfaces can connect sensors or external transceivers, while IrDA supports short-range infrared communication in suitable designs. At 50 MHz, the Cortex-M4 core can handle sampling, filtering, protocol framing, and low-rate application logic. Its 32 KB Flash and 8 KB SRAM limit firmware and buffering capacity, so the design should avoid unnecessary code duplication and use DMA where appropriate. The package minimizes board area but requires careful BGA assembly.
Được đề xuất
Communication Module
The verified UART/USART, SPI, I2C, IrDA, and I2S feature set gives the MK10DX32VMP5 enough interface breadth for a compact communication module or protocol gateway. The 50 MHz Cortex-M4 core can execute framing, timing, buffering, and supervisory tasks while DMA reduces processor involvement in serial transfers. SPI is useful for radio or storage companions, while UART/USART supports external modems, debug consoles, and field-service links. I2C can connect configuration devices or sensors. Firmware memory is constrained at 32 KB Flash, so protocol stack size and boot overhead should be reviewed during component selection.
Được đề xuất
Motor and Motion Control
The MK10DX32VMP5 can serve as a compact motor-control front end when the design uses its verified PWM, timer, DMA, and communication resources. PWM outputs can command motor drivers or generate actuator control signals, while UART/USART can connect to a host or tuning interface. The 50 MHz Cortex-M4 core provides useful control-loop throughput for basic positioning, speed, or PWM management. The 32 KB Flash and 8 KB SRAM are modest for advanced algorithms, so complex motion stacks should be evaluated separately. Exact timer channels, pin mapping, analog features, and timing performance require confirmation from the official NXP documentation.
Được đề xuất
Low-Power Embedded Product
The NXP Kinetis K10 positioning makes the MK10DX32VMP5 relevant to space- and cost-constrained products that need more capability than a very small baseline controller. The verified baseline, low-power family description, 8 KB SRAM, and watchdog support can support supervisory or peripheral-control functions. Low-voltage detection and power-on reset are useful for reliable startup and supply monitoring. The exact sleep currents, wake-up times, clock-tree settings, and operating voltage range are not included in the supplied snippets, so battery-life claims and power-mode planning require the manufacturer datasheet.
Được đề xuất
Audio and Digital Interface
The MK10DX32VMP5's verified I2S and I2C connectivity can support compact digital audio or interface-control subsystems. I2S may connect to a codec or digital audio peripheral, while I2C is commonly used for codec configuration and control. The Cortex-M4 core can manage control registers, basic signal routing, status monitoring, and communication with a higher-level processor. This is not a high-performance audio DSP position: the verified 32 KB Flash and 8 KB SRAM constrain buffer size and software complexity. Audio clocking, data formats, pin multiplexing, and signal-integrity requirements should be validated against the official datasheet.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho MK10DX32VMP5 — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | MK20DX32VMP5 | MK20DN32VMP5 | MK10DX128VMP5 | MK21FN1M0VLQ12 | MK22FN128VMP10 |
|---|---|---|---|---|---|---|
| Package | 64-MAPBGA (5 x 5 mm) | 64-MAPBGA (5 x 5 mm) | 64-MAPBGA (5 x 5 mm) | 64-MAPBGA (5 x 5 mm) | 64-MAPBGA (5 x 5 mm) | 64-MAPBGA (5 x 5 mm) |
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
Bảo phân biệt quan trọng
- Compact 5 x 5 mm package integration (vsLarger-package Kinetis designs)
- 50 MHz Cortex-M4 control performance (vsLower-performance baseline controllers)
- Integrated serial and timing peripherals (vsSimple microcontroller solutions requiring external interface expansion)
Ghi chú thiết kế
Treat the 64-MAPBGA package as a high-density layout constraint. Place all decoupling and support components close to the relevant power and ground balls, preserve the manufacturer-recommended ball map, and validate escape-routing density with the actual PCB stack-up. Because no complete pinout or package drawing was included in the supplied data, do not begin routing from inferred ball assignments.
Verify the device voltage limits and power-sequencing requirements against the official NXP datasheet before connecting external rails or I2C/SPI peripherals. The supplied Arrow snippet references 1.8 V, 2.5 V, and 3.3 V, but it does not establish the complete operating range or I/O limits. Use appropriately rated level shifters and ensure every connected interface cannot exceed the MCU's absolute maximum ratings.
Do not treat a similar Kinetis part number as an automatic drop-in replacement. Compare the 64-ball assignment, power and ground balls, boot configuration pins, Flash and SRAM capacity, clock pins, peripheral multiplexing, and software device support. The cross-reference results identify comparison candidates but do not prove pin compatibility, so an engineering review and hardware regression test are required before substitution.
Thông tin tuân thủ
The supplied verified search results identify the part as an active NXP microcontroller but do not provide RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declarations. Confirm these statuses on the current NXP product documentation and applicable distributor declarations.
