MK10DX32VMP5 - 50MHz Cortex-M4 32KB MCU | NXP | 64-MAPBGA
부품 번호: MK10DX32VMP5 ✓ 활성| 수량 | 단가 | 합계 |
|---|---|---|
| 1 | $0 | $0.00 |
| 10 | $0 | $0.00 |
| 100 | $0 | $0.00 |
| 500 | $0 | $0.00 |
| 1,000 | $0 | $0.00 |
MK10DX32VMP5 개요
A microcontroller is a programmable semiconductor system that combines a CPU core, memory, communication interfaces, timers, analog functions, and control peripherals on one integrated circuit. The MK10DX32VMP5 belongs to the ARM Cortex-M4 microcontroller family, commonly used in embedded control, motor-control, communications, and industrial systems. Its 32-bit architecture and 50 MHz operating frequency provide a practical balance between processing capability, power consumption, and integration.
Key verified features include a 50 MHz ARM Cortex-M4 core, 32 KB (32K x 8) Flash program memory, 8 KB SRAM, and a 5 x 5 mm 64-MAPBGA package. The available interface set includes I2C, SPI, UART/USART, IrDA, I2S, DMA, PWM, a watchdog timer, low-voltage detection, and power-on reset. The 44 I/O count provides connection flexibility for sensors, actuators, communications, and human-interface circuitry in compact embedded products.
The Kinetis K10 family provides a scalable entry point into the Kinetis portfolio while integrating analog, communication, timing, and control peripherals. This makes the device suitable for applications that need broad peripheral support without moving to a larger package or higher-performance MCU. Exact operating voltage, temperature range, pin assignments, flash endurance, and detailed electrical limits were not included in the supplied verified snippets and must be confirmed from the official NXP datasheet before design release.
Typical uses include low-cost industrial controllers, compact sensor nodes, communication modules, motor and motion-control subsystems, and low-power embedded products. The 64-MAPBGA footprint is especially useful where PCB area is constrained, although its fine pitch requires careful assembly and inspection processes. Designers should confirm the exact package pinout, exposed-pad requirements, power architecture, decoupling recommendations, and software support using NXP documentation.
For replacement or second sourcing, compare the complete NXP ordering information, package drawing, pin multiplexing, memory size, clock configuration, peripheral set, and software migration requirements. A part with a similar listed processor or package may not be pin-compatible or functionally equivalent. This page combines verified distributor snippets with explicit data gaps rather than estimating unavailable electrical specifications.
드롭인 대체품: MK10DX32VMP5 — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: MK10DX32VMP5 (동일 폼 팩터 및 풋프린트) — 차이점: Package, Mounting Type, Connectivity, Maximum Clock Frequency, Product Type.
빠른 비교 도구 — 나란히 비교할 대체 부품을 선택하십시오:
MK20DX32VMP5
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
MK20DN32VMP5
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
MK10DX128VMP5
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
MK21FN1M0VLQ12
✅ 드롭인✓ 재고 있음
$9.2 / 개
데이터시트 보기 →MK22FN128VMP10
✅ 드롭인✓ 재고 있음
$3.18 / 개
데이터시트 보기 →MK10DX32VMP5 최대 정격 & 전기적 특성
| Product Type | 32-bit ARM Cortex-M4 Kinetis K10 microcontroller |
| Core Processor | ARM Cortex-M4 |
| 최대 클록 주파수 | 50 MHz |
| Flash Memory | 32 KB (32K x 8) |
| SRAM | 8 KB |
| Architecture | 32-bit RISC |
| 패키지 | 64-MAPBGA, 5 x 5 mm |
| Number of I/O Pins | 44 I/O |
| Connectivity | I2C, IrDA, SPI, UART/USART |
| Peripheral Support | DMA, I2S, LVD, POR, PWM, WDT |
| Operating Feature Class | Baseline, low-power Kinetis MCU |
| 수명 주기 상태 | Active |
| 실장 유형 | Surface-mount BGA |
| Package Ball Count | 64 balls |
MK10DX32VMP5 64 balls 핀 구성 가이드
MK10DX32VMP5(64 balls 패키지)의 핀 구성입니다. 이 디지털 IC에는 GPIO, 통신 인터페이스(UART, SPI, I2C), 전원 핀이 포함되어 있습니다. 대체 핀 기능과 구성 옵션은 제조사 데이터시트를 참조하십시오. 임베디드 시스템 설계와 PCB 레이아웃에 필수적입니다.
다음에 대한 상세 핀아웃 데이터 없음: MK10DX32VMP5.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
MK10DX32VMP5 적합 용도: 6 애플리케이션s: Compact Industrial Control, Sensor and IoT Node, Communication Module, Motor and Motion Control, Low-Power Embedded Product, Audio and Digital Interface.
Compact Industrial Control
The MK10DX32VMP5 fits compact control boards that need a 50 MHz Cortex-M4 core without the memory footprint of a larger MCU. Its verified 32 KB Flash and 8 KB SRAM are suitable for supervisory logic, state machines, parameter handling, and moderate peripheral coordination. UART/USART and I2C can connect local sensors or service interfaces, while PWM and watchdog functions support actuator monitoring and system recovery. The 44 I/O pins provide useful connectivity in a 5 x 5 mm 64-MAPBGA package, although the exact ball assignment and electrical limits must be verified before PCB release.
추천
Sensor and IoT Node
The MK10DX32VMP5 is a practical fit for small sensor nodes that must combine local processing with serial connectivity. The verified I2C and SPI interfaces can connect sensors or external transceivers, while IrDA supports short-range infrared communication in suitable designs. At 50 MHz, the Cortex-M4 core can handle sampling, filtering, protocol framing, and low-rate application logic. Its 32 KB Flash and 8 KB SRAM limit firmware and buffering capacity, so the design should avoid unnecessary code duplication and use DMA where appropriate. The package minimizes board area but requires careful BGA assembly.
추천
Communication Module
The verified UART/USART, SPI, I2C, IrDA, and I2S feature set gives the MK10DX32VMP5 enough interface breadth for a compact communication module or protocol gateway. The 50 MHz Cortex-M4 core can execute framing, timing, buffering, and supervisory tasks while DMA reduces processor involvement in serial transfers. SPI is useful for radio or storage companions, while UART/USART supports external modems, debug consoles, and field-service links. I2C can connect configuration devices or sensors. Firmware memory is constrained at 32 KB Flash, so protocol stack size and boot overhead should be reviewed during component selection.
추천
Motor and Motion Control
The MK10DX32VMP5 can serve as a compact motor-control front end when the design uses its verified PWM, timer, DMA, and communication resources. PWM outputs can command motor drivers or generate actuator control signals, while UART/USART can connect to a host or tuning interface. The 50 MHz Cortex-M4 core provides useful control-loop throughput for basic positioning, speed, or PWM management. The 32 KB Flash and 8 KB SRAM are modest for advanced algorithms, so complex motion stacks should be evaluated separately. Exact timer channels, pin mapping, analog features, and timing performance require confirmation from the official NXP documentation.
추천
Low-Power Embedded Product
The NXP Kinetis K10 positioning makes the MK10DX32VMP5 relevant to space- and cost-constrained products that need more capability than a very small baseline controller. The verified baseline, low-power family description, 8 KB SRAM, and watchdog support can support supervisory or peripheral-control functions. Low-voltage detection and power-on reset are useful for reliable startup and supply monitoring. The exact sleep currents, wake-up times, clock-tree settings, and operating voltage range are not included in the supplied snippets, so battery-life claims and power-mode planning require the manufacturer datasheet.
추천
Audio and Digital Interface
The MK10DX32VMP5's verified I2S and I2C connectivity can support compact digital audio or interface-control subsystems. I2S may connect to a codec or digital audio peripheral, while I2C is commonly used for codec configuration and control. The Cortex-M4 core can manage control registers, basic signal routing, status monitoring, and communication with a higher-level processor. This is not a high-performance audio DSP position: the verified 32 KB Flash and 8 KB SRAM constrain buffer size and software complexity. Audio clocking, data formats, pin multiplexing, and signal-integrity requirements should be validated against the official datasheet.
추천
추천 제품 요약
엔지니어링 참조 데이터: MK10DX32VMP5 — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | MK20DX32VMP5 | MK20DN32VMP5 | MK10DX128VMP5 | MK21FN1M0VLQ12 | MK22FN128VMP10 |
|---|---|---|---|---|---|---|
| Package | 64-MAPBGA (5 x 5 mm) | 64-MAPBGA (5 x 5 mm) | 64-MAPBGA (5 x 5 mm) | 64-MAPBGA (5 x 5 mm) | 64-MAPBGA (5 x 5 mm) | 64-MAPBGA (5 x 5 mm) |
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
주요 차별점
- Compact 5 x 5 mm package integration (vs Larger-package Kinetis designs)
- 50 MHz Cortex-M4 control performance (vs Lower-performance baseline controllers)
- Integrated serial and timing peripherals (vs Simple microcontroller solutions requiring external interface expansion)
설계 노트
Treat the 64-MAPBGA package as a high-density layout constraint. Place all decoupling and support components close to the relevant power and ground balls, preserve the manufacturer-recommended ball map, and validate escape-routing density with the actual PCB stack-up. Because no complete pinout or package drawing was included in the supplied data, do not begin routing from inferred ball assignments.
Verify the device voltage limits and power-sequencing requirements against the official NXP datasheet before connecting external rails or I2C/SPI peripherals. The supplied Arrow snippet references 1.8 V, 2.5 V, and 3.3 V, but it does not establish the complete operating range or I/O limits. Use appropriately rated level shifters and ensure every connected interface cannot exceed the MCU's absolute maximum ratings.
Do not treat a similar Kinetis part number as an automatic drop-in replacement. Compare the 64-ball assignment, power and ground balls, boot configuration pins, Flash and SRAM capacity, clock pins, peripheral multiplexing, and software device support. The cross-reference results identify comparison candidates but do not prove pin compatibility, so an engineering review and hardware regression test are required before substitution.
규정 준수 정보
The supplied verified search results identify the part as an active NXP microcontroller but do not provide RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declarations. Confirm these statuses on the current NXP product documentation and applicable distributor declarations.
