MKL25Z32VFM4 - 48MHz Cortex-M0+ 32KB Flash USB MCU | NXP
MPN: MKL25Z32VFM4 ✓ Hoạt độngMKL25Z32VFM4 Tóm tắt
A microcontroller (MCU) is a single integrated circuit containing a CPU core, memory, and peripherals on a single die. The ARM Cortex-M0+ architecture used here is a compact, low-cost 32-bit processor defined by the Arm Architecture Compact Instruction set, intended for cost-sensitive embedded control. In the Kinetis family hierarchy the MKL25Z32VFM4 sits in the KL2 sub-family, which extends the KL1x line by adding a full-speed USB 2.0 OTG controller or a full-speed crystal-less USB 2.0 device controller. That positioning makes it a natural fit for USB-connected sensors, dongles, and low-power data acquisition nodes.
Key features include a 48 MHz Cortex-M0+ core, 32 KB (32K x 8) on-chip flash for program storage, 4 KB of SRAM for working memory, and a full-speed USB 2.0 device/OTG controller that can be clocked from an internal oscillator, removing the need for an external crystal when precision timing is not required. The part is offered in a 32-HVQFN 5 x 5 mm package with a 0.5 mm pitch, allowing a very small board footprint for USB dongles and wearable accessories.
Technically, the KL2 sub-family is designed for ultra-low-power operation: the core sleeps with a low active current and the part can be clocked from the internal 8 MHz oscillator trimmed to USB accuracy, saving both board area and BOM cost. The KL25 series is source-compatible with the Kinetis K20 (Cortex-M4) MCUs and with the rest of the Kinetis KL1x, KL2x, KL3x and KL4x families, giving a clear migration path when a design outgrows its memory budget or peripheral set. The reference manual covering MKL25Z32VFM4 and its siblings is document KL25P80M48SF0RM.
Typical applications include USB-to-serial adapters, HID and CDC class dongles, low-power environmental sensing nodes, battery-operated portable measurement instruments, USB-connected battery chargers, and compact industrial data acquisition modules where a full-size 48 MHz Cortex-M4 would be unnecessary.
When designing around this device, pay attention to the exposed-pad ground connection and the USB D+/D- routing. The 5 x 5 mm HVQFN has a limited thermal escape area, so for sustained high clock rates with USB traffic, pour a full ground plane beneath the package and keep the USB trace pair short, 50-ohm differential-impedance controlled, and free of test-point stubs.
This page consolidates manufacturer part data, package and memory details, drop-in same-footprint alternatives in the 32-QFN 5 x 5 mm land pattern, and practical layout and USB routing guidance into a single engineering reference that goes beyond a distributor catalogue listing.
Bộ thay thế dễ dàng lắp đặt cho MKL25Z32VFM4 — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với MKL25Z32VFM4 (cùng hình factor và footprint) — khác nhau ở Architecture, Flash Memory, Package, Product Family, SRAM.
MKL25Z64VFM4
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →MKL25Z128VFM4
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
MKL26Z32VFM4
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
MKL24Z32VFM4
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
MKL25Z32VFT4
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
MKL25Z32VFM4 Tỷ lệ tối đa & tính chất điện
| Core Processor | ARM Cortex-M0+ (32-bit) |
| Maximum CPU Frequency | 48 MHz |
| Flash Memory | 32 KB (32K x 8) |
| SRAM | 4 KB |
| Product Family | Kinetis KL2 (KL25) |
| USB Controller | Full-speed USB 2.0 OTG / crystal-less device controller |
| Architecture | Arm Cortex-M0+ compact instruction set, 32-bit |
| Hộp | 32-HVQFN (5 x 5 mm), 0.5 mm pitch |
| Kiểu lắp đặt | Surface Mount |
| Terminal Count | 32 pins |
| Family Software Compatibility | Compatible with Kinetis K20, KL1x, KL2x, KL3x and KL4x MCUs |
Hướng dẫn cấu hình chân MKL25Z32VFM4 32-hvqfn (5 x 5 mm), 0.5 mm pitch
Cấu hình chân cho MKL25Z32VFM4 (32-hvqfn (5 x 5 mm), 0.5 mm pitch gói). IC số này bao gồm chân GPIO, giao diện truyền thông (UART, SPI, I2C) và chân nguồn. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết các chức năng chân thay thế và tùy chọn cấu hình. Cực kỳ quan trọng cho thiết kế hệ thống tích hợp và lập trình PCB.
Không có dữ liệu chân cụ thể sẵn có cho MKL25Z32VFM4.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
MKL25Z32VFM4 phù hợp cho 6 Áp dụngs: USB HID and CDC Peripherals, Battery-Powered Environmental Sensing, Portable Measurement Instruments, USB-to-RS232 and Industrial Gateways, Wearables and Personal Electronics, USB Battery Charging and Power Management.
USB HID and CDC Peripherals
The MKL25Z32VFM4 fits USB dongles, keypad and mouse interfaces, and CDC-class adapters because it integrates a full-speed USB 2.0 device controller directly on the die, so no separate USB bridge IC is required. Because the KL2x family includes a crystal-less USB device controller, the PHY can run from the internal trimmed oscillator and the external 24 MHz crystal plus its load capacitors can be left off the board, which saves both BOM cost and layout area in a compact dongle form factor. The 48 MHz Cortex-M0+ core handles enumeration, HID report generation and command parsing comfortably, while 32 KB of flash and 4 KB of SRAM are sufficient for typical HID or CDC class firmware. The main trade-off is that the 32 KB flash budget limits protocol stack complexity, so designs that add composite USB classes should step up to the 64 KB variant.
Được đề xuất
Battery-Powered Environmental Sensing
For battery-operated environmental and industrial sensing nodes, the MKL25Z32VFM4 offers a compact control solution that combines a 48 MHz ARM Cortex-M0+ core with the ultra-low-power design of the Kinetis KL2 sub-family. The controller runs sensor duty-cycled measurement sequences and reports results over the on-board full-speed USB device controller, which simultaneously powers the node from a host port and carries data, eliminating a separate radio or battery charger in USB-deployed installations. With 4 KB of SRAM and 32 KB of flash, typical applications hold a calibration table, a periodic log buffer and a small state machine. The 32-HVQFN 5 x 5 mm footprint keeps the node small, and the reduced-leakage sleep modes help extend the interval between service visits.
Được đề xuất
Portable Measurement Instruments
The MKL25Z32VFM4 is a strong fit for compact handheld meters and portable test instruments where a USB port is the primary interface to a laptop. The on-chip full-speed USB 2.0 controller streams samples to the host, and the 48 MHz Cortex-M0+ core provides the timing headroom for continuous conversion loops and front-panel logic. Because the USB device controller can run without an external crystal, the instrument designer keeps the board small while still supporting USB enumeration for a direct driverless data path. The 32 KB flash supports a bootloader plus the measurement firmware, and 4 KB of SRAM covers sample buffering in typical single-channel or low-channel acquisition setups. When a firmware update path with two image slots is needed, the 64 KB sibling in the same footprint is the usual upgrade.
Được đề xuất
USB-to-RS232 and Industrial Gateways
In industrial gateway and converter designs the MKL25Z32VFM4 bridges a USB host port to downstream serial or field-bus circuitry, combining a 48 MHz Cortex-M0+ core with the USB 2.0 device controller in a single 32-HVQFN 5 x 5 mm package. The core handles protocol translation, buffering of received frames and simple supervisory logic without a discrete USB interface chip, which reduces board area and cost in multi-port gateway products. Its low-power modes are valuable in gateways that run from a single rail and must survive long idle periods, and the small land pattern leaves routing room for the downstream transceivers. Engineers typically pair it with a dedicated RS-232 or isolation transceiver and pay attention to the exposed pad ground connection and to keeping the USB differential pair short.
Được đề xuất
Wearables and Personal Electronics
The MKL25Z32VFM4 suits wearables and personal electronic accessories that expose a USB charging or configuration port, because the integrated full-speed USB device controller handles enumeration while the ultra-low-power Kinetis KL2 architecture keeps standby consumption low between interactions. The 5 x 5 mm HVQFN package is small enough for tight enclosures, and the 48 MHz Cortex-M0+ core is more than sufficient for gesture, step-count or haptic-control workloads with 32 KB of flash for application code and 4 KB of SRAM for state. Because the family can be clocked from the internal oscillator for USB operation, a crystal-less design further shrinks the wearable board. The trade-off is that the 32 KB memory ceiling limits rich UI logic, so wearables needing graphics or extensive data logging should use a larger-memory part in the same footprint.
Được đề xuất
USB Battery Charging and Power Management
The MKL25Z32VFM4 is well suited to USB-powered charger and portable power modules where the MCU must negotiate with the host, manage a power path and report status over the same cable. The integrated full-speed USB 2.0 controller removes the need for a discrete USB interface device, and the KL2 family's crystal-less operation means the charger module can enumerate from the internal oscillator when cost is critical. The 48 MHz Cortex-M0+ core is fast enough to run the USB stack alongside state-machine-based charge control and current-loop supervision. Four kilobytes of SRAM accommodates the control state and measurement buffers, and 32 KB of flash holds the USB descriptors and control firmware. The small 32-HVQFN footprint suits compact adapters, though designs needing larger descriptor tables or data logging should step to the 64 KB or 128 KB siblings.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho MKL25Z32VFM4 — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | MKL25Z64VFM4 | MKL25Z128VFM4 | MKL26Z32VFM4 | MKL24Z32VFM4 | MKL25Z32VFT4 |
|---|---|---|---|---|---|---|
| Package | 32-HVQFN (5 x 5 mm) | 32-HVQFN (5 x 5 mm) - same | 32-HVQFN (5 x 5 mm) - same | 32-HVQFN (5 x 5 mm) - same | 32-HVQFN (5 x 5 mm) - same | 32-HVQFN (5 x 5 mm) - same |
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Core Processor | ARM Cortex-M0+ (32-bit) | ARM Cortex-M0+ (32-bit) | ARM Cortex-M0+ (32-bit) | ARM Cortex-M0+ (32-bit) | ARM Cortex-M0+ (32-bit) | ARM Cortex-M0+ (32-bit) |
| Maximum CPU Frequency | 48 MHz | 48 MHz | 48 MHz | 48 MHz | 48 MHz | 48 MHz |
| Flash Memory | 32 KB (32K x 8) | 64 KB | 128 KB | 32 KB (32K x 8) | 32 KB (32K x 8) | 32 KB (32K x 8) |
| SRAM | 4 KB | 4 KB | 4 KB | 4 KB | 4 KB | 4 KB |
| USB Controller | Full-speed USB 2.0 OTG / crystal-less device controller | Full-speed USB 2.0 OTG / crystal-less device controller | Full-speed USB 2.0 OTG / crystal-less device controller | Full-speed USB 2.0 OTG / crystal-less device controller | No USB 2.0 controller (KL24 sub-family) | Full-speed USB 2.0 OTG / crystal-less device controller |
| Peripheral Set | Kinetis KL25 baseline | Kinetis KL25 baseline | Kinetis KL25 baseline | Kinetis KL26 with expanded analog and GPIO resources | Kinetis KL24 baseline without USB | Kinetis KL25 baseline, commercial temperature grade |
| Lifecycle Status | Active | Active | Active | Active | Active | Active |
Bảo phân biệt quan trọng
- On-die full-speed USB 2.0 controller (vsMKL24Z32VFM4)
- Crystal-less USB operation (vsMKL25Z64VFM4)
- Exact memory match for lean firmware (vsMKL25Z128VFM4)
- Peripheral headroom via a pin-compatible step-up (vsMKL26Z32VFM4)
- Family migration path across Kinetis (vsMKL25Z32VFT4)
Ghi chú thiết kế
The 32-HVQFN 5 x 5 mm package has a small thermal escape area, so pour a continuous ground plane directly beneath the exposed pad and connect it with the same number of vias as the package drawing specifies. Keep the USB D+/D- differential pair short, referenced to the same ground plane, with no stubs to test points or connectors; a 90 ohm differential pair with matched length is the standard target for full-speed USB. Route the pair away from switching nodes and inductor areas to keep the USB PHY free of radiated noise.
Place all decoupling capacitors adjacent to the supply pins, with the bulk capacitor closest to the device, and provide a clean ground return for each capacitor rather than routing returns through the exposed pad region. Because the KL2x family can operate the USB device controller from the internal oscillator, omitting the 24 MHz crystal frees board area, but if an external crystal is fitted it must be placed next to the oscillator pins with a short ground guard, otherwise startup and enumeration margins shrink.
Two frequent design errors are mismatched memory expectations and incorrect temperature grade assumptions. The MKL25Z32VFM4 gives 32 KB of flash and 4 KB of SRAM; USB stacks, bootloader plus application images and logging quickly exhaust 32 KB, so plan the 64 KB or 128 KB sibling in the identical footprint early. Second, the VFM4 and VFT4 order codes differ in grade, so verify the suffix against the required ambient temperature range before releasing the BOM.
The Kinetis KL2 sub-family is built for low-power operation, but USB activity raises the average current draw well above sleep current. Estimate the average supply requirement from the USB enumeration and polling duty cycle plus the load current of attached peripherals, then size the 3.3 V rail and its decoupling for that average rather than the sleep figure. Using the internal oscillator saves the crystal's supply load and its associated capacitors, which helps in battery-backed installations where the node is powered from the USB port.
Do not assume a drop-in from a non-NXP Cortex-M0+ MCU. The MKL25Z32VFM4 pinout follows the Kinetis 32-QFN 5 x 5 mm arrangement, with the USB pins, SWD debug interface, reset and power pins positioned per the KL25 sub-family data sheet pin description tables; a generic 32-QFN MCU will not match these functions. Verify every pin in the data sheet tables and confirm that the USB D+/D- lines are connected to the correct connector pins for the chosen device class.
Thông tin tuân thủ
NXP lists the MKL25Z32VFM4 as active with environmental quality and shipping information provided on the official part page, but the specific RoHS, REACH, halogen-free and conflict-minerals declarations were not available in the retrieved listing content, so they are recorded as unknown. The device is a microcontroller, so AEC-Q100 qualification is not applicable unless a -Q1 automotive order code is selected.