MSP430F148IPAG - 16-Bit 8MHz Mixed-Signal MCU | Texas Instruments
MPN: MSP430F148IPAG ✓ Hoạt độngMSP430F148IPAG Tóm tắt
An MSP430 mixed-signal microcontroller combines a low-power 16-bit RISC processor with analog and communication peripherals on one integrated circuit. It belongs to the MSP430 family of ultra-low-power embedded controllers, where the CPU, timers, ADC, serial interfaces, and digital I/O support battery-powered sensing, industrial instrumentation, meter, and control products. Its reduced instruction set, 16-bit registers, and constant generators help firmware execute efficiently within tight memory and energy budgets.
The MSP430F148IPAG is suited to designs that need both measurement and serial connectivity without adding separate analog and interface ICs. Its 12-bit ADC supports analog signal acquisition, while the comparator provides a hardware threshold function useful in sensor conditioning and protection. Two USART channels and an SPI interface enable communication with displays, data loggers, wireless modules, and external converters. Two built-in 16-bit timers support periodic sampling, timing, pulse counting, and motor or actuator control.
Operation is specified from 1.8 V to 3.6 V, making the device suitable for low-voltage embedded systems. Low-power behavior includes 280 µA active current at 1 MHz and 2.2 V, 1.6 µA standby current, and 0.1 µA off-state current with RAM retention. Five power-saving modes and standby wake-up in less than 6 µs support duty-cycled measurement systems that spend most of their operating time asleep.
Typical uses include portable environmental monitors, industrial sensor nodes, energy meters, programmable control panels, and embedded instrumentation. In a battery-powered transmitter, the ADC can sample a sensor while the timer schedules conversion events and the SPI or UART communicates with a peripheral. Duty cycling between active and low-power states can extend battery life while preserving fast response.
PCB design should preserve the device's analog and digital grounding strategy, place decoupling capacitors close to supply pins, and route high-impedance ADC inputs away from switching nodes. External oscillator, reset, and programming connections must follow the pin-description table in the manufacturer datasheet. Software developers should also budget for startup code, memory mapping, watchdog handling, and the MSP430 architecture's interrupt and low-power conventions.
This page consolidates the device's core specifications, package information, suitable embedded applications, design considerations, and qualified drop-in alternatives. It is intended to help engineers locate the correct programming and datasheet information before committing a mixed-signal control board to production.
Bộ thay thế dễ dàng lắp đặt cho MSP430F148IPAG — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với MSP430F148IPAG (cùng hình factor và footprint) — khác nhau ở Package, ADC Resolution, Comparator, Flash Memory, Supply Voltage Range.
MSP430F148IPM
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →MSP430F148IPMG4
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
MSP430F149IPAG
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →MSP430F149IPM
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →MSP430F148IPAG Tỷ lệ tối đa & tính chất điện
| Architecture | 16-bit RISC |
| CPU Family | MSP430x1xx |
| Tần số xung maksimum | 8 MHz |
| Flash Memory | 48 KB |
| SRAM | 2 KB |
| ADC Resolution | 12 bits |
| Comparator | Integrated |
| SPI Interface | Integrated |
| UART Interface | Integrated |
| Number of USART Channels | 2 |
| Timers | 2 x 16-bit |
| General-Purpose I/O | 48 pins |
| Supply Voltage Range | 1.8 V to 3.6 V |
| Active Current | 280 µA at 1 MHz and 2.2 V |
| Standby Current | 1.6 µA |
| Off Current with RAM Retention | 0.1 µA |
| Power-Saving Modes | 5 |
| Standby Wake-Up Time | Less than 6 µs |
| Hộp | 64-pin TQFP, 10 mm x 10 mm |
| Kiểu lắp đặt | Surface Mount |
Hướng dẫn cấu hình chân MSP430F148IPAG 64-pin tqfp, 10 mm x 10 mm
Cấu hình chân cho MSP430F148IPAG (64-pin tqfp, 10 mm x 10 mm gói). IC số này bao gồm chân GPIO, giao diện truyền thông (UART, SPI, I2C) và chân nguồn. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết các chức năng chân thay thế và tùy chọn cấu hình. Cực kỳ quan trọng cho thiết kế hệ thống tích hợp và lập trình PCB.
Không có dữ liệu chân cụ thể sẵn có cho MSP430F148IPAG.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
MSP430F148IPAG phù hợp cho 6 Áp dụngs: Battery-Powered Environmental Sensors, Industrial Data Acquisition, Energy and Utility Metering, Portable Medical Monitoring, Programmable Control Panels, Actuator and Motor Control.
Battery-Powered Environmental Sensors
The MSP430F148IPAG suits battery-powered environmental sensors because it combines a 12-bit ADC with low standby current of 1.6 µA and a supply range of 1.8 V to 3.6 V. A timer can initiate periodic analog conversions, while the MCU sleeps between readings to reduce energy consumption. Its 280 µA active current at 1 MHz and 2.2 V, together with wake-up below 6 µs, supports responsive duty-cycled measurement without requiring a separate analog converter. The two USART channels can connect to a local display or calibration interface, while SPI can serve a compact digital sensor. Firmware should disable unused peripherals during sleep and retain only the state required between samples.
Được đề xuất
Industrial Data Acquisition
The MSP430F148IPAG is appropriate for compact industrial data-acquisition equipment that must acquire analog measurements and transfer data through multiple serial interfaces. Its 12-bit ADC and comparator support sensor monitoring, threshold detection, and signal conditioning, while the two 16-bit timers support accurate sampling intervals. Two USART channels allow simultaneous connection to a local console and host computer, and SPI can communicate with a higher-speed peripheral. Operation down to 1.8 V supports compact industrial instrument designs. Engineers should account for analog grounding, input filtering, and calibration, because the MCU can orchestrate acquisition timing but cannot eliminate sensor drift or external interference without suitable front-end circuitry.
Được đề xuất
Energy and Utility Metering
The MSP430F148IPAG can serve as the control and measurement core in a low-power energy meter where a dedicated MCU, analog front end, and communication controller would otherwise increase board complexity. Its integrated 12-bit ADC acquires sensor signals, the comparator provides a hardware threshold reference, and the timers support periodic measurement. The low-power operating modes help minimize consumption between polling intervals, while SPI and two USART channels provide expansion paths for a display, memory, or communications module. Firmware should define calibration tables, anti-aliasing filters, rollover handling, and data-integrity checks. The 48 KB flash capacity is sufficient for many metering applications, but the F149 option provides additional code space when protocol and logging features expand.
Được đề xuất
Portable Medical Monitoring
The MSP430F148IPAG can support compact portable monitoring equipment where low power, mixed-signal measurement, and local connectivity are important. Its 12-bit ADC acquires sensor signals, the comparator supports threshold-based detection, and the timers establish repeatable sampling periods. The low-power supply range and standby current of 1.6 µA permit longer operation between charges, while SPI and UART provide interfaces for sensors, displays, or a host processor. For medical applications, use the MCU as a controlled measurement component rather than relying on it as the sole safety mechanism. External protection, calibration, isolation, and validation are still required according to the intended standard and use case. Firmware should include sensor diagnostics and predictable fault recovery.
Được đề xuất
Programmable Control Panels
The MSP430F148IPAG fits programmable control panels that combine analog input monitoring with serial communications and timer-based control functions. Its 48 I/O pins provide substantial digital control capability, two USART channels can connect to a human-interface module and external equipment, and SPI can support display or storage devices. The two 16-bit timers help implement debouncing, periodic updates, pulse generation, or basic motor timing. At 8 MHz, the 16-bit RISC processor provides a straightforward platform for user-interface logic and supervisory control. Layout should keep switching regulators and high-current outputs away from sensitive analog inputs, while firmware should separate safety-critical checks from ordinary panel functions and define behavior during communication loss.
Được đề xuất
Actuator and Motor Control
The MSP430F148IPAG can coordinate low-power actuator or motor-control functions where accurate timing and multiple I/O resources are required. Its two 16-bit timers support periodic control, pulse-width measurement, and input capture, while 48 I/O pins handle limit switches, digital sensors, and driver-control signals. The comparator and 12-bit ADC can monitor feedback or supply conditions, and the serial interfaces permit configuration and diagnostics. For a motor circuit, the MCU should command a dedicated power driver rather than directly driving motor current. Validate timing under worst-case interrupt load, use safe output states during reset, and include mechanical limits and fault shutdown in the system design. Low-power modes can reduce idle consumption when motion is infrequent.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho MSP430F148IPAG — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | MSP430F148IPM | MSP430F148IPMG4 | MSP430F149IPAG | MSP430F149IPM |
|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 64-TQFP (10x10 mm) | 64-TQFP (10x10 mm) | 64-TQFP (10x10 mm) | 64-TQFP (10x10 mm) | 64-TQFP (10x10 mm) |
| CPU Architecture | 16-bit RISC | 16-bit RISC | 16-bit RISC | 16-bit RISC | 16-bit RISC |
| Maximum Clock Frequency | 8 MHz | 8 MHz | 8 MHz | 8 MHz | 8 MHz |
| Flash Memory | 48 KB | 48 KB | 48 KB | 59 KB | 59 KB |
| SRAM | 2 KB | 2 KB | 2 KB | 2 KB | 2 KB |
| ADC Resolution | 12 bits | 12 bits | 12 bits | 12 bits | 12 bits |
| Supply Voltage Range | 1.8 V to 3.6 V | 1.8 V to 3.6 V | 1.8 V to 3.6 V | 1.8 V to 3.6 V | 1.8 V to 3.6 V |
| Communication Peripherals | SPI, 2 USART channels | SPI, 2 USART channels | SPI, 2 USART channels | SPI, 2 USART channels | SPI, 2 USART channels |
| General-Purpose I/O | 48 pins | 48 pins | 48 pins | 48 pins | 48 pins |
Bảo phân biệt quan trọng
- Matches the established MSP430F148 configuration without changing memory architecture (vsMSP430F148IPM)
- Provides additional code storage while retaining the 64-pin footprint (vsMSP430F149IPAG)
- Integrates multiple serial interfaces and analog functions in one MCU (vsMSP430F148IPMG4)
Ghi chú thiết kế
Assign every connection from the official 64-pin TQFP pin-description table and preserve the exposed supply and ground requirements. Place decoupling capacitors immediately beside their associated supply pins, provide adequate return paths for both analog and digital currents, and avoid routing ADC inputs beneath noisy switching nodes. Check every analog-capable pin because multiplexed peripheral functions can affect the external circuit.
Estimated active power at the stated 2.2 V and 1 MHz operating point is 616 mW using 2.2 V and 280 µA, before accounting for peripheral and IO loading. Use this only as a preliminary duty-cycle estimate, then calculate average consumption from the actual clock rate, enabled peripherals, sleep interval, and regulator efficiency. Select the external supply and decoupling for the peak active condition rather than the average standby figure.
Do not infer automotive qualification or environmental compliance solely from the MSP430 family name. Confirm the exact MSP430F148IPAG ordering suffix, temperature grade, lifecycle status, and production documentation with Texas Instruments. Likewise, verify the complete pin configuration and startup requirements in the manufacturer datasheet before treating any family member as a production substitute.
Keep analog inputs short, use a continuous ground reference beneath them, and isolate high-impedance nodes from digital switching traces. The integrated comparator and ADC are useful for sensing, but external filtering and protection may still be needed. Review the datasheet's analog operating recommendations and include calibration or offset correction when measurement precision must remain stable across temperature and supply changes.
Thông tin tuân thủ
The available product information identifies the MSP430F148IPAG as an industrial 64-pin TQFP configuration but does not explicitly provide RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declarations. Confirm the current documents for the exact ordering code.