Texas Instruments

MSP430F148IPAG - 16-Bit 8MHz Mixed-Signal MCU | Texas Instruments

MPN: MSP430F148IPAG ✓ 啟用中
1.8 V to 3.6 V Vdss 280 µA at 1 MHz and 2.2 V Id 64-pin TQFP, 10 mm x 10 mm Package 8 MHz Speed 48 KB Memory
MOQ: 1 |

MSP430F148IPAG 概覽

The Texas Instruments MSP430F148IPAG is a 16-bit mixed-signal microcontroller with an 8 MHz MSP430 RISC core, 48 KB of flash memory, 2 KB of SRAM, and a 12-bit ADC in a 64-pin TQFP package. The device also integrates a comparator, SPI, UART interfaces, two 16-bit timers, and 48 I/O pins for compact embedded-control designs.

An MSP430 mixed-signal microcontroller combines a low-power 16-bit RISC processor with analog and communication peripherals on one integrated circuit. It belongs to the MSP430 family of ultra-low-power embedded controllers, where the CPU, timers, ADC, serial interfaces, and digital I/O support battery-powered sensing, industrial instrumentation, meter, and control products. Its reduced instruction set, 16-bit registers, and constant generators help firmware execute efficiently within tight memory and energy budgets.

The MSP430F148IPAG is suited to designs that need both measurement and serial connectivity without adding separate analog and interface ICs. Its 12-bit ADC supports analog signal acquisition, while the comparator provides a hardware threshold function useful in sensor conditioning and protection. Two USART channels and an SPI interface enable communication with displays, data loggers, wireless modules, and external converters. Two built-in 16-bit timers support periodic sampling, timing, pulse counting, and motor or actuator control.

Operation is specified from 1.8 V to 3.6 V, making the device suitable for low-voltage embedded systems. Low-power behavior includes 280 µA active current at 1 MHz and 2.2 V, 1.6 µA standby current, and 0.1 µA off-state current with RAM retention. Five power-saving modes and standby wake-up in less than 6 µs support duty-cycled measurement systems that spend most of their operating time asleep.

Typical uses include portable environmental monitors, industrial sensor nodes, energy meters, programmable control panels, and embedded instrumentation. In a battery-powered transmitter, the ADC can sample a sensor while the timer schedules conversion events and the SPI or UART communicates with a peripheral. Duty cycling between active and low-power states can extend battery life while preserving fast response.

PCB design should preserve the device's analog and digital grounding strategy, place decoupling capacitors close to supply pins, and route high-impedance ADC inputs away from switching nodes. External oscillator, reset, and programming connections must follow the pin-description table in the manufacturer datasheet. Software developers should also budget for startup code, memory mapping, watchdog handling, and the MSP430 architecture's interrupt and low-power conventions.

This page consolidates the device's core specifications, package information, suitable embedded applications, design considerations, and qualified drop-in alternatives. It is intended to help engineers locate the correct programming and datasheet information before committing a mixed-signal control board to production.

直接替換替代品,適用於 MSP430F148IPAG — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。

此系列的變體

與下列產品可直接替換的同系列型號: MSP430F148IPAG (相同外形與佔位) — 差異在於 Package, ADC Resolution, Comparator, Flash Memory, Supply Voltage Range.

Texas Instruments
Package: 64-pin LQFP (PM), 10 x 10 mm
ADC Resolution: 12 bit
Supply Voltage Range: 2.5 V to 3.3 V
比較對象 MSP430F148IPAG →
Texas Instruments
Package: 64-TQFP, 10 mm x 10 mm
ADC Resolution: 12-bit
Comparator: Integrated comparator
比較對象 MSP430F148IPAG →
Texas Instruments
Package: 64-LQFP (PM), 10x10 mm
比較對象 MSP430F148IPAG →

MSP430F148IPM

✅ 直接替換
Texas Instruments
📦 64-TQFP (10x10 mm)
16-bit MSP430 RISC · 8 MHz · 48 KB · 2 KB · 12 bit · Integrated · SPI and UART · 2

聯絡詢價

查看資料表 →

MSP430F148IPMG4

✅ 直接替換
📦 64-TQFP (10x10 mm)
Same MSP430F148 electrical configuration and 64-pin footprint; ordering suffix differs, with 0% change to core, memory, or voltage ratings

📋 參考替代品(不在目錄中)

MSP430F149IPAG

✅ 直接替換 ⚠️ 規格未經驗證
Texas Instruments
📦 64-TQFP (10x10 mm)
16-bit RISC mixed-signal microcontroller · 8 MHz · 60 KB · 2 KB · 12-bit · Integrated comparator · SPI/UART · Integrated hardware multiplier

聯絡詢價

查看資料表 →

MSP430F149IPM

✅ 直接替換 ⚠️ 規格未經驗證
Texas Instruments
📦 64-TQFP (10x10 mm)
MSP430 CPU16 (16-bit RISC) · MSP430x1xx · 8 MHz · 60 KB Flash (60K x 8 + 256B info) · 2 KB · 1.8 V to 3.6 V · 280 µA · 1.6 µA

聯絡詢價

查看資料表 →

MSP430F148IPAG 最大額定值與電氣特性

Architecture 16-bit RISC
CPU Family MSP430x1xx
最大時脈頻率 8 MHz
Flash Memory 48 KB
SRAM 2 KB
ADC Resolution 12 bits
Comparator Integrated
SPI Interface Integrated
UART Interface Integrated
Number of USART Channels 2
Timers 2 x 16-bit
General-Purpose I/O 48 pins
Supply Voltage Range 1.8 V to 3.6 V
Active Current 280 µA at 1 MHz and 2.2 V
Standby Current 1.6 µA
Off Current with RAM Retention 0.1 µA
Power-Saving Modes 5
Standby Wake-Up Time Less than 6 µs
封裝 64-pin TQFP, 10 mm x 10 mm
安裝類型 Surface Mount

MSP430F148IPAG 64-pin tqfp, 10 mm x 10 mm 腳位配置指南

MSP430F148IPAG(64-pin tqfp, 10 mm x 10 mm 封裝)的腳位配置。 此數位 IC 包含 GPIO、通訊介面(UART、SPI、I2C)與電源腳位。替代腳位功能與配置選項請參閱製造商資料表。對嵌入式系統設計與 PCB 佈局至關重要。

MSP430F148IPAG 的 64-pin tqfp, 10 mm x 10 mm 封裝腳位圖

無詳細腳位定義資料: MSP430F148IPAG.

請參閱 資料表 以查看完整腳位配置。

典型應用

MSP430F148IPAG 適用於 6 應用s: Battery-Powered Environmental Sensors, Industrial Data Acquisition, Energy and Utility Metering, Portable Medical Monitoring, Programmable Control Panels, Actuator and Motor Control.

🧩

Battery-Powered Environmental Sensors

The MSP430F148IPAG suits battery-powered environmental sensors because it combines a 12-bit ADC with low standby current of 1.6 µA and a supply range of 1.8 V to 3.6 V. A timer can initiate periodic analog conversions, while the MCU sleeps between readings to reduce energy consumption. Its 280 µA active current at 1 MHz and 2.2 V, together with wake-up below 6 µs, supports responsive duty-cycled measurement without requiring a separate analog converter. The two USART channels can connect to a local display or calibration interface, while SPI can serve a compact digital sensor. Firmware should disable unused peripherals during sleep and retain only the state required between samples.

🏭

Industrial Data Acquisition

The MSP430F148IPAG is appropriate for compact industrial data-acquisition equipment that must acquire analog measurements and transfer data through multiple serial interfaces. Its 12-bit ADC and comparator support sensor monitoring, threshold detection, and signal conditioning, while the two 16-bit timers support accurate sampling intervals. Two USART channels allow simultaneous connection to a local console and host computer, and SPI can communicate with a higher-speed peripheral. Operation down to 1.8 V supports compact industrial instrument designs. Engineers should account for analog grounding, input filtering, and calibration, because the MCU can orchestrate acquisition timing but cannot eliminate sensor drift or external interference without suitable front-end circuitry.

⚡

Energy and Utility Metering

The MSP430F148IPAG can serve as the control and measurement core in a low-power energy meter where a dedicated MCU, analog front end, and communication controller would otherwise increase board complexity. Its integrated 12-bit ADC acquires sensor signals, the comparator provides a hardware threshold reference, and the timers support periodic measurement. The low-power operating modes help minimize consumption between polling intervals, while SPI and two USART channels provide expansion paths for a display, memory, or communications module. Firmware should define calibration tables, anti-aliasing filters, rollover handling, and data-integrity checks. The 48 KB flash capacity is sufficient for many metering applications, but the F149 option provides additional code space when protocol and logging features expand.

💊

Portable Medical Monitoring

The MSP430F148IPAG can support compact portable monitoring equipment where low power, mixed-signal measurement, and local connectivity are important. Its 12-bit ADC acquires sensor signals, the comparator supports threshold-based detection, and the timers establish repeatable sampling periods. The low-power supply range and standby current of 1.6 µA permit longer operation between charges, while SPI and UART provide interfaces for sensors, displays, or a host processor. For medical applications, use the MCU as a controlled measurement component rather than relying on it as the sole safety mechanism. External protection, calibration, isolation, and validation are still required according to the intended standard and use case. Firmware should include sensor diagnostics and predictable fault recovery.

🔧

Programmable Control Panels

The MSP430F148IPAG fits programmable control panels that combine analog input monitoring with serial communications and timer-based control functions. Its 48 I/O pins provide substantial digital control capability, two USART channels can connect to a human-interface module and external equipment, and SPI can support display or storage devices. The two 16-bit timers help implement debouncing, periodic updates, pulse generation, or basic motor timing. At 8 MHz, the 16-bit RISC processor provides a straightforward platform for user-interface logic and supervisory control. Layout should keep switching regulators and high-current outputs away from sensitive analog inputs, while firmware should separate safety-critical checks from ordinary panel functions and define behavior during communication loss.

🔧

Actuator and Motor Control

The MSP430F148IPAG can coordinate low-power actuator or motor-control functions where accurate timing and multiple I/O resources are required. Its two 16-bit timers support periodic control, pulse-width measurement, and input capture, while 48 I/O pins handle limit switches, digital sensors, and driver-control signals. The comparator and 12-bit ADC can monitor feedback or supply conditions, and the serial interfaces permit configuration and diagnostics. For a motor circuit, the MCU should command a dedicated power driver rather than directly driving motor current. Validate timing under worst-case interrupt load, use safe output states during reset, and include mechanical limits and fault shutdown in the system design. Low-power modes can reduce idle consumption when motion is infrequent.

What is the MSP430F148IPAG?
The MSP430F148IPAG is a Texas Instruments 16-bit mixed-signal microcontroller operating at up to 8 MHz with 48 KB of flash, 2 KB of SRAM, and a 12-bit ADC. According to the manufacturer product page, the device also integrates a comparator, SPI, UART interfaces, two 16-bit timers, and 48 I/O pins in a 64-pin TQFP package. It is designed for low-power embedded measurement and control systems.
What are the key specifications of MSP430F148IPAG that engineers should know?
The MSP430F148IPAG combines an 8 MHz 16-bit RISC core, 48 KB of flash, 2 KB of SRAM, and a 12-bit ADC in a 64-pin TQFP package. According to Texas Instruments, it provides two 16-bit timers, two USART channels, SPI, a comparator, and 48 I/O pins. Its 1.8 V to 3.6 V supply range, five low-power modes, and standby wake-up below 6 µs make it suitable for battery-operated and duty-cycled systems.
Where can I download the MSP430F148IPAG datasheet PDF?
The official MSP430F148IPAG technical information is available on the Texas Instruments product page at https://www.ti.com/product/MSP430F148. The manufacturer page provides ordering information, technical parameters, device documentation, and the official datasheet PDF. Use that document for the complete 64-pin description, timing characteristics, electrical limits, and recommended application circuit before assigning PCB connections or setting production test conditions.
Where can I find the MSP430F148IPAG pinout?
The MSP430F148IPAG pinout is published in the manufacturer datasheet associated with the MSP430F148 product page. The device uses a 64-pin TQFP package, so engineers should assign every physical pin from the package pin-description table rather than relying on a generic 64-pin drawing. Confirm signal names, analog-capable pins, supply inputs, ground connections, test points, and programming pins directly against the current Texas Instruments documentation.
How much current does the MSP430F148IPAG use?
The MSP430F148IPAG consumes 280 µA in active mode at 1 MHz and 2.2 V according to the MSP430F148 product information. Standby current is 1.6 µA, while off-state current with RAM retention is 0.1 µA. These figures show why the device is useful in portable instruments: the firmware can suspend operation between measurements and restore fast operation through a standby wake-up time below 6 µs.
Is MSP430F148IPAG suitable for battery-powered sensor systems?
Yes, the MSP430F148IPAG is suitable for battery-powered sensor systems because it operates from 1.8 V to 3.6 V and supports five power-saving modes. According to the manufacturer product page, active current is 280 µA at 1 MHz and 2.2 V, standby current is 1.6 µA, and standby wake-up occurs in less than 6 µs. Its integrated 12-bit ADC, timers, and serial interfaces reduce the need for additional components.
MSP430F148IPAG vs MSP430F148IPM - which is better?
The MSP430F148IPAG and MSP430F148IPM are pin-compatible members of the same MSP430F148 family, but their orderable suffixes can indicate different package or qualification details. The MSP430F148IPAG is identified as the 64-pin TQFP industrial configuration, while MSP430F148IPM is another 64-pin TQFP ordering option. Review the manufacturer ordering table for temperature grade and packing code before deciding which suffix belongs in the production BOM.
When should I choose MSP430F148IPAG over MSP430F149IPAG?
Choose MSP430F148IPAG when 48 KB of flash and 2 KB of SRAM are sufficient and you need the established MSP430F148 mixed-signal feature set. The MSP430F149IPAG offers the same general 64-pin TQFP platform and MSP430 architecture but provides additional flash memory. Select the F149 variant when firmware storage is the limiting factor, and select the F148 variant when its 48 KB of flash is adequate.
What can replace the MSP430F148IPAG?
A true drop-in replacement for the MSP430F148IPAG must use the same 64-pin TQFP footprint, preserve pin assignments, and provide compatible supply, memory, and peripheral characteristics. MSP430F148IPM, MSP430F148IPMG4, MSP430F149IPAG, and MSP430F149IPM are relevant same-family candidates. Final substitution should be checked against the manufacturer pin-description and ordering tables, particularly for qualification, temperature grade, flash size, and firmware assumptions.
Is the MSP430F148IPAG the same as MSP430F149IPAG?
No, the MSP430F148IPAG and MSP430F149IPAG are closely related but not identical devices. The MSP430F148IPAG has 48 KB of flash, while the MSP430F149IPAG provides additional flash within the same MSP430F14x family and 64-pin TQFP platform. Their shared architecture supports family-level software portability, but memory-size assumptions, startup configuration, and code-size limits must be reviewed before treating one as a direct substitution.
What is the best drop-in replacement for MSP430F148IPAG?
The closest drop-in choices include MSP430F148IPM and MSP430F148IPMG4 because they retain the MSP430F148 identity, 64-pin TQFP package, 8 MHz core, 48 KB flash, and 2 KB SRAM. MSP430F149IPAG and MSP430F149IPM preserve the family architecture and footprint while adding flash. Verify ordering codes and qualification details before production use because package compatibility alone does not establish every ordering-code requirement.
Where can I buy MSP430F148IPAG online?
Use the Request a Quote form on this page to request MSP430F148IPAG availability, current lead time, and a unit quotation. The form provides the appropriate purchasing path without requiring a static price commitment. Include your required quantity, reel quantity, target date, and production status so the request can be matched to the exact MSP430F148IPAG ordering code rather than a related MSP430F148 variant.
What is the price of MSP430F148IPAG?
Current MSP430F148IPAG pricing is not stated here because commercial terms and availability can change. Submit the Request a Quote form on this page with your quantity and required delivery schedule. The form avoids presenting an outdated or non-binding figure and lets the purchasing team confirm the exact 64-pin TQFP ordering code, packing format, lead time, and shipment quantity.
What is the lead time and stock status for MSP430F148IPAG?
Request the current MSP430F148IPAG lead time and stock allocation through the Request a Quote form on this page. Include your order quantity, shipment date, and whether reel packaging is required. Because inventory and manufacturing schedules can vary, the request should be used to confirm current availability for the exact MSP430F148IPAG suffix rather than relying on a general MSP430F148 family status.
Which programming and debugging tools work with MSP430F148IPAG?
The MSP430F148IPAG uses the MSP430 programming architecture, so compatible tools include Texas Instruments MSP430 debuggers and flash programmers that support the device family. According to the manufacturer product information, the MCU includes the resources required for embedded firmware, while the official datasheet defines reset and programming connections. Confirm the exact debugger, target board interface, and device support in the tool vendor's hardware list before production use.
Is MSP430F148IPAG RoHS, REACH, or AEC-Q100 qualified?
The MSP430F148IPAG ordering information identifies an industrial 64-pin TQFP configuration, but the available manufacturer excerpts do not explicitly state RoHS, REACH, or AEC-Q100 status. Confirm those declarations on the Texas Instruments product page or in the current environmental and quality documentation for the exact ordering code. Automotive production designs should require explicit AEC-Q100 qualification rather than inferring it from the general MSP430 family.

工程參考資料,適用於 MSP430F148IPAG — 比較、設計指引及合規資訊。

選型指南

Choose the MSP430F148IPAG for a new 64-pin TQFP design that requires an 8 MHz MSP430 controller, 48 KB of flash, 2 KB of SRAM, a 12-bit ADC, SPI, two USART channels, and low-power operation. Choose MSP430F148IPM when its ordering code better matches your qualification or packing requirements and verify the suffix-specific details. Choose MSP430F149IPAG or MSP430F149IPM when the shared footprint is desirable but the additional flash is needed for larger firmware, logging, or protocol stacks. None of these choices should be made from package appearance alone: check temperature grade, qualification, memory limits, pin functions, and lifecycle documentation in the manufacturer ordering information. The F149 options are most useful when code capacity is the principal constraint; otherwise, the F148 configuration offers a simpler match to the target design.

與替代品比較

參數 本產品 MSP430F148IPM MSP430F148IPMG4 MSP430F149IPAG MSP430F149IPM
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments
Package 64-TQFP (10x10 mm) 64-TQFP (10x10 mm) 64-TQFP (10x10 mm) 64-TQFP (10x10 mm) 64-TQFP (10x10 mm)
CPU Architecture 16-bit RISC 16-bit RISC 16-bit RISC 16-bit RISC 16-bit RISC
Maximum Clock Frequency 8 MHz 8 MHz 8 MHz 8 MHz 8 MHz
Flash Memory 48 KB 48 KB 48 KB 59 KB 59 KB
SRAM 2 KB 2 KB 2 KB 2 KB 2 KB
ADC Resolution 12 bits 12 bits 12 bits 12 bits 12 bits
Supply Voltage Range 1.8 V to 3.6 V 1.8 V to 3.6 V 1.8 V to 3.6 V 1.8 V to 3.6 V 1.8 V to 3.6 V
Communication Peripherals SPI, 2 USART channels SPI, 2 USART channels SPI, 2 USART channels SPI, 2 USART channels SPI, 2 USART channels
General-Purpose I/O 48 pins 48 pins 48 pins 48 pins 48 pins

主要差異化特點

  • Matches the established MSP430F148 configuration without changing memory architecture (對比MSP430F148IPM)
  • Provides additional code storage while retaining the 64-pin footprint (對比MSP430F149IPAG)
  • Integrates multiple serial interfaces and analog functions in one MCU (對比MSP430F148IPMG4)

設計說明

Assign every connection from the official 64-pin TQFP pin-description table and preserve the exposed supply and ground requirements. Place decoupling capacitors immediately beside their associated supply pins, provide adequate return paths for both analog and digital currents, and avoid routing ADC inputs beneath noisy switching nodes. Check every analog-capable pin because multiplexed peripheral functions can affect the external circuit.

Estimated active power at the stated 2.2 V and 1 MHz operating point is 616 mW using 2.2 V and 280 µA, before accounting for peripheral and IO loading. Use this only as a preliminary duty-cycle estimate, then calculate average consumption from the actual clock rate, enabled peripherals, sleep interval, and regulator efficiency. Select the external supply and decoupling for the peak active condition rather than the average standby figure.

Do not infer automotive qualification or environmental compliance solely from the MSP430 family name. Confirm the exact MSP430F148IPAG ordering suffix, temperature grade, lifecycle status, and production documentation with Texas Instruments. Likewise, verify the complete pin configuration and startup requirements in the manufacturer datasheet before treating any family member as a production substitute.

Keep analog inputs short, use a continuous ground reference beneath them, and isolate high-impedance nodes from digital switching traces. The integrated comparator and ADC are useful for sensing, but external filtering and protection may still be needed. Review the datasheet's analog operating recommendations and include calibration or offset correction when measurement precision must remain stable across temperature and supply changes.

合規資訊

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
無鉛
Unknown
無鹵
Unknown
衝突礦產
Unknown

The available product information identifies the MSP430F148IPAG as an industrial 64-pin TQFP configuration but does not explicitly provide RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declarations. Confirm the current documents for the exact ordering code.

相關搜尋

MSP430F148IPAG datasheet MSP430F148IPAG pinout MSP430F148IPAG datasheet pdf MSP430F148IPAG specifications MSP430F148IPAG equivalent MSP430F148IPAG replacement MSP430F148IPAG cross reference MSP430F148IPAG price MSP430F148IPAG stock Texas Instruments MSP430F148IPAG MSP430F148IPAG vs MSP430F148IPM MSP430F148 64 TQFP pinout MSP430F148IPAG low power application MSP430F148IPAG programming tool

相關元件與詞彙

Texas Instruments MSP430F148IPAG MSP430F148IPM MSP430F148IPMG4 MSP430F149IPAG MSP430F149IPM MSP430 MSP430x1xx mixed-signal microcontroller 16-bit RISC architecture embedded microcontroller semiconductor 12-bit ADC analog comparator SPI UART USART 16-bit timer 48 KB flash memory 2 KB SRAM 1.8 V to 3.6 V low supply voltage ultra-low-power mode 64-pin TQFP TQFP family surface-mount package industrial data acquisition battery-powered sensor energy metering
快速報價 RFQ
請填寫完整詳細資料 — 我們的業務團隊將於 24 小時內回覆
料號 製造商 封裝 QTY 目標價格 小計
✓
報價已提交!

我們將於 24 小時內回覆您的電子郵件

1
詢價已提交
2
已收到報價
3
已下單
4
付款
5
已出貨
6
已送達
檢視詢價單詳情