MSP430F5325IPN - 25MHz 64KB Flash Mixed-Signal MCU | Texas Instruments
MPN: MSP430F5325IPN ✓ Hoạt độngMSP430F5325IPN Tóm tắt
A mixed-signal microcontroller combines a digital processor with analog measurement or control peripherals on one device. In the broader semiconductor hierarchy, the MSP430F5325 belongs to the mixed-signal MCU class, then the 16-bit MCU category, and ultimately the embedded microcontroller and semiconductor families. Its MSP430 CPU architecture uses 16-bit registers and a RISC-based instruction set designed for efficient control-oriented software.
The principal advantages are the 25 MHz operating frequency, 64 KB Flash program memory, and 6 KB SRAM. The 12-bit ADC supports analog measurement, the comparator provides a lower-power threshold-detection option, and DMA permits peripheral transfers without continuous processor intervention. Two USCIs expand serial connectivity, with UART, SPI, and I2C functions identified for this device.
The MSP430F5325 family combines four 16-bit timers with an RTC and alarm capability, making it suitable for periodic sensing, event timing, and low-duty-cycle control. A hardware multiplier accelerates arithmetic operations that are common in control, measurement, and signal-processing firmware. The integrated 3.3 V LDO simplifies supply architecture when the operating and external interface requirements are compatible with that internal rail.
Typical uses include industrial sensor acquisition, building and automation controllers, energy measurement instruments, low-power data loggers, communications equipment, and battery-operated monitoring systems. The 63 available I/O pins allow multiple sensors, actuators, indicators, and serial interfaces to be connected while preserving a moderate integration level rather than using several discrete components.
Designers should confirm every peripheral multiplexing, voltage-domain constraint, pin-function alternative, and package connection from the manufacturer datasheet before laying out the PCB. The 80-pin LQFP footprint requires careful escape routing, and mixed-signal designs should separate sensitive ADC inputs from switching nodes and digital return currents.
This page combines the manufacturer feature set, package and memory information, exact-MPN pricing evidence, application guidance, and package-compatible family options. It also distinguishes confirmed drop-in options from candidates that require firmware, memory, and peripheral revalidation before production release.
Bộ thay thế dễ dàng lắp đặt cho MSP430F5325IPN — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với MSP430F5325IPN (cùng hình factor và footprint) — khác nhau ở Hardware Multiplier, SRAM.
MSP430F5329IPN
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →MSP430F5327IPN
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
MSP430F5325IPN Tỷ lệ tối đa & tính chất điện
| CPU Architecture | 16-bit MSP430 RISC |
| Tần số xung maksimum | 25 MHz |
| Flash Memory | 64 KB |
| SRAM | 6 KB |
| ADC Resolution | 12 bit |
| Comparator | Integrated |
| DMA Controller | Integrated |
| UART | Integrated |
| SPI | Integrated |
| I2C | Integrated |
| USCI Count | 2 |
| Hardware Multiplier | Integrated |
| Timer Count | 4 x 16-bit |
| Real-Time Clock | Integrated with alarm capability |
| Internal LDO | 3.3 V |
| I/O Pin Count | 63 |
| Hộp | 80-pin LQFP (PN), 12 x 12 mm |
| Kiểu lắp đặt | Surface mount |
Hướng dẫn cấu hình chân MSP430F5325IPN 80-pin lqfp (pn), 12 x 12 mm
Cấu hình chân cho MSP430F5325IPN (80-pin lqfp (pn), 12 x 12 mm gói). IC số này bao gồm chân GPIO, giao diện truyền thông (UART, SPI, I2C) và chân nguồn. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết các chức năng chân thay thế và tùy chọn cấu hình. Cực kỳ quan trọng cho thiết kế hệ thống tích hợp và lập trình PCB.
Không có dữ liệu chân cụ thể sẵn có cho MSP430F5325IPN.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
MSP430F5325IPN phù hợp cho 6 Áp dụngs: Industrial Sensor Acquisition, Low-Power Data Logger, Building Automation Controller, Energy Measurement Instrument, Communications Gateway, Battery-Operated Monitoring System.
Industrial Sensor Acquisition
MSP430F5325IPN fits industrial sensor acquisition because its 12-bit ADC, comparator, four 16-bit timers, and 63 I/O pins provide enough resources for multiple analog and digital inputs without requiring separate interface chips. At 25 MHz, the MCU can service control logic while DMA transfers data between peripherals and the 6 KB SRAM. Two USCIs support UART, SPI, or I2C sensor links. The 64 KB Flash accommodates acquisition firmware, calibration tables, and protocol handlers. In a deployed measurement system, place the analog section near the ADC inputs, follow the datasheet source-impedance and filtering requirements, and reserve timer outputs for excitation or trigger timing.
Được đề xuất
Low-Power Data Logger
The MSP430F5325IPN supports low-power data logging through its MSP430 control architecture, integrated timers, RTC alarm capability, and low-duty-cycle sensor interfaces. The 64 KB Flash provides space for firmware and logged event information, while the 6 KB SRAM can hold active measurement batches before storage. DMA can move peripheral data without requiring the CPU to supervise every transfer, and the comparator can support threshold-based wake events. The two USCIs allow a local flash or communications peripheral to operate alongside the ADC. Battery-operated designs should use the datasheet's clocking, port-state, and sleep-mode guidance to minimize current draw.
Được đề xuất
Building Automation Controller
MSP430F5325IPN can serve as a building-automation controller where a design combines analog monitoring with digital I/O, timers, and serial communications. Its 63 I/O pins allow inputs from temperature, occupancy, pressure, or flow sensors and outputs for indicators or actuator interfaces. Four 16-bit timers support periodic sampling and output timing, while the RTC and alarm functions enable scheduled operations. The 25 MHz CPU and 64 KB Flash are suitable for protocol stacks, state machines, and local filtering. During hardware design, assign multiplexed functions from the pin table, observe power-domain restrictions, and route high-switching-current outputs away from sensitive analog inputs.
Được đề xuất
Energy Measurement Instrument
MSP430F5325IPN is suitable for energy-measurement instrumentation because it combines a 12-bit ADC, comparator, hardware multiplier, DMA, and two configurable serial communication interfaces. The ADC can acquire voltage-derived signals, the comparator can provide fast threshold detection, and the hardware multiplier assists arithmetic used in scaling and calibration calculations. Four timers can organize sampling and communication periods, while 64 KB Flash stores fixed-point routines, calibration data, and communications code. The 6 KB SRAM limits simultaneous buffering, so define DMA transfer sizes carefully. Follow the datasheet's ADC acquisition, reference, and analog-input recommendations to maintain repeatable measurements.
Được đề xuất
Communications Gateway
MSP430F5325IPN can be used in a small communications gateway that must combine local control, protocol conversion, and analog supervision. Its two USCIs provide UART, SPI, or I2C connectivity, while DMA supports efficient movement of serial or peripheral data through the 6 KB SRAM. At 25 MHz, the 16-bit MSP430 CPU can manage framing, checksums, configuration, and supervisory logic. The 64 KB Flash is sufficient for compact gateway firmware, although larger protocol stacks or buffered traffic may require a different MCU configuration. Validate serial pin multiplexing and interrupt priorities in the device documentation, and use independent protection for externally accessible communication lines.
Được đề xuất
Battery-Operated Monitoring System
MSP430F5325IPN fits battery-operated monitoring systems that periodically measure analog conditions and transmit results through a serial link. Its RTC with alarm capability supports time-based sampling, while the comparator can generate an event when a monitored signal crosses a threshold. The 25 MHz CPU handles acquisition sequencing and protocol formatting, and DMA reduces processor involvement during peripheral transfers. The integrated 3.3 V LDO can simplify internal rail generation where the system supply and external interface levels meet its operating requirements. Confirm the complete supply and I/O voltage ranges in the manufacturer datasheet, disable unused peripherals, and select the lowest suitable clock and sleep configuration for the duty cycle.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho MSP430F5325IPN — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | MSP430F5329IPN | MSP430F5327IPN |
|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 80-LQFP (PN, 12 x 12 mm) | 80-LQFP (PN, 12 x 12 mm) | 80-LQFP (PN, 12 x 12 mm) |
| CPU Architecture | 16-bit MSP430 RISC | 16-bit MSP430 RISC | 16-bit MSP430 RISC |
| Maximum Clock Frequency | 25 MHz | 25 MHz | 25 MHz |
| ADC Resolution | 12 bit | 12 bit | 12 bit |
| Timer Count | 4 x 16-bit | 4 x 16-bit | 4 x 16-bit |
| USCI Count | 2 | 2 | 2 |
| I/O Pin Count | 63 | 63 | 63 |
| Internal LDO | 3.3 V | 3.3 V | 3.3 V |
Bảo phân biệt quan trọng
- Confirmed memory configuration (vsMSP430F5329IPN)
- Mixed-signal integration (vsMSP430F5327IPN)
- 25 MHz control headroom (vsMSP430F5329IPN)
Ghi chú thiết kế
Assign the 63 available I/O functions from the manufacturer pin-description table before routing the 80-pin LQFP PCB. Several analog, digital, timer, and serial functions may be multiplexed on the same package terminal. Confirm the selected alternate function, direction, pull configuration, and permitted voltage domain for every used pin. Keep unused inputs at a defined electrical state and follow the datasheet recommendations for unused I/O termination.
Treat ADC inputs and references as sensitive analog nets. Place input filtering and protection components near the MCU pins, use a quiet ground reference for the analog section, and avoid routing digital clock, UART, SPI, and switching-node traces beneath or immediately beside the analog inputs. The 12-bit conversion accuracy depends on the complete signal chain, so account for source impedance, acquisition time, reference stability, and PCB leakage rather than relying only on nominal converter resolution.
The MSP430F5325IPN includes an integrated 3.3 V LDO, but its use does not remove the need to verify the device's complete supply, I/O, and internal-rail limits in the manufacturer datasheet. Select an input source that satisfies those limits, provide the required decoupling at the relevant supply pins, and account for voltage levels on every externally connected signal. Do not assume that all communication interfaces use the same allowable voltage domain.
A shared LQFP footprint does not by itself establish firmware compatibility. Before releasing MSP430F5329IPN or MSP430F5327IPN as a replacement, compare memory capacities and map, interrupt priorities, port multiplexing, analog-channel assignments, timer and RTC resources, boot behavior, and electrical limits. Preserve a production artifact containing the original firmware, calibration data, and hardware revision to support controlled regression testing.
Thông tin tuân thủ
Compliance status requires confirmation from the current manufacturer product documentation or declaration for the exact ordering code.