OPA606KP - 13MHz DIFET Op Amp | Texas Instruments
MPN: OPA606KP ✓ Hoạt độngOPA606KP Tóm tắt
An operational amplifier is an analog building block that amplifies the voltage difference between its differential inputs while using negative feedback to set the closed-loop gain. The OPA606 belongs to the instrumentation-amplifier and general-purpose op-amp hierarchy: it combines high open-loop gain, wide frequency response, low offset voltage, low bias current, and fast slew performance in one precision analog IC.
The OPA606KP uses Texas Instruments’ Difet operational-amplifier technology to achieve a 13 MHz gain-bandwidth product and 30 V/µs slew rate. Its input bias current is 8 pA, while input offset voltage is 78 dB lower than a typical mV-level bipolar amplifier, with the manufacturer describing the offset-voltage characterization in dB. The device includes a single amplifier, supports operation from 10 V to 36 V total supply voltage, and is supplied in a through-hole 8-PDIP package.
Because its 13 MHz bandwidth and 30 V/µs slew rate can reproduce high-frequency signal transitions, the OPA606KP is well suited to instrumentation preamplifiers, active filters, wideband buffers, laboratory test circuits, and signal converters. Its 8 pA input bias current also helps preserve accuracy when the source presents very high impedance.
The 8-pin DIP construction favors legacy instrumentation, educational, prototype, and industrial control systems where through-hole assembly and socketed maintenance are useful. Its wide supply range also allows operation from conventional ±5 V and ±15 V laboratory rails, although input and output voltage limits must be respected during startup and saturation.
For reliable operation, place a short feedback path close to the amplifier, use low-leakage nodes around the high-impedance input, and decouple each supply rail near the package. Check the stable-gain configuration in the manufacturer datasheet, especially when driving capacitive loads or operating at gain levels where the amplifier’s frequency-response characteristics become critical.
This page combines the OPA606KP’s manufacturer characteristics with package-specific selection guidance, verified drop-in alternatives, and practical design notes for high-impedance and wideband analog circuits.
Bộ thay thế dễ dàng lắp đặt cho OPA606KP — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
OPA606KP-3
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
OPA606KP Tỷ lệ tối đa & tính chất điện
| Amplifier Type | Single operational amplifier |
| Gain-Bandwidth Product | 13 MHz |
| Slew Rate | 30 V/µs |
| Supply Voltage Range | ±5 V to ±18 V |
| Total Supply Voltage Range | 10 V to 36 V |
| Input Bias Current | 8 pA |
| Input Offset Voltage | 78 dB characterization |
| Điện áp tối đa đầu ra | 10 mA per channel |
| Number of Amplifiers | 1 |
| Số lượng chân | 8 |
| Package Type | 8-PDIP |
| Package Body Width | 0.300 in (7.62 mm) |
| Technology | DIFET |
| Kiểu lắp đặt | Through-hole |
Hướng dẫn cấu hình chân OPA606KP 0.300 in (7.62 mm)
Cấu hình chân cho OPA606KP (0.300 in (7.62 mm) gói). Thành phần số hiệu này có chân đầu vào, đầu ra và nguồn cung cấp. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết cấu hình chân bù, bù trừ và chân kích hoạt. Hoàn hảo cho điều kiện tín hiệu và mạch khuếch đại.
Không có dữ liệu chân cụ thể sẵn có cho OPA606KP.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
OPA606KP phù hợp cho 6 Áp dụngs: Precision Instrumentation Preamp, Wideband Active Filter, Laboratory Buffer, Test and Measurement Signal Conditioning, Audio and Communication Interface, Data Acquisition Front End.
Precision Instrumentation Preamp
The OPA606KP is appropriate for the input stage of a laboratory or process instrumentation circuit because its 8 pA input bias current creates very little error across a high-impedance sensor. The 13 MHz gain-bandwidth product also allows the amplifier to process signals beyond the bandwidth of many general-purpose precision op amps. Place the device close to the sensor input, use guarded high-impedance nodes, and keep feedback components compact to reduce parasitic capacitance and leakage.
Được đề xuất
Wideband Active Filter
OPA606KP can implement a wideband active-filter section when signal bandwidth matters and a 30 V/µs slew rate is required for clean large-signal transitions. Its 13 MHz gain-bandwidth product provides the loop bandwidth needed for practical low-pass, high-pass, or band-pass networks operating well above audio frequencies. Component tolerances and op-amp gain-bandwidth behavior determine the achieved response, so the filter should be simulated and stability-checked for the selected noise-gain curve.
Được đề xuất
Laboratory Buffer
OPA606KP is useful as a wideband unity-gain buffer for buffering oscillators, sensor outputs, and test fixtures. The 30 V/µs slew rate preserves large-amplitude, high-frequency signal edges better than a slow precision amplifier, while the 8 pA bias current limits loading of high-impedance sources. Confirm unity-gain stability and capacitive-load behavior in the manufacturer datasheet, and connect the feedback directly to the output to minimize parasitic feedback paths.
Được đề xuất
Test and Measurement Signal Conditioning
OPA606KP suits test and measurement front ends that must condition moderate-frequency signals without introducing excessive slew-rate distortion. Its 13 MHz gain-bandwidth product and 30 V/µs slew rate support waveform capture, gain stages, and impedance-conversion circuits around sensors and transducers. For high-precision DC measurements, evaluate input offset voltage and drift at the intended temperature; for high-source-impedance sources, pay particular attention to the 8 pA input bias current.
Được đề xuất
Audio and Communication Interface
OPA606KP can be used in line-level audio or communications interfaces that benefit from more bandwidth than conventional general-purpose op amps provide. The 13 MHz gain-bandwidth product and 30 V/µs slew rate provide margin for higher-frequency signal components and reduce slew-induced distortion. The single amplifier is suitable for an active filter, gain cell, or line driver, but output-current capability, load impedance, and output-voltage swing should be checked against the required channel load.
Được đề xuất
Data Acquisition Front End
OPA606KP works as a gain and drive stage ahead of an ADC when the acquisition path requires more bandwidth than a conventional precision amplifier provides. Its 30 V/µs slew rate helps maintain large-signal integrity, and its 8 pA bias current reduces input-stage error for high-impedance sources. The design must account for ADC input capacitance, settling time, and the amplifier’s stability with capacitive loads, using the manufacturer datasheet’s recommended values and typical application circuits.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho OPA606KP — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | OPA606KP-3 |
|---|---|---|
| Brand | Texas Instruments | Texas Instruments |
| Package | 8-PDIP | 8-PDIP |
| Amplifier Type | Single operational amplifier | Single operational amplifier |
Bảo phân biệt quan trọng
- Wide-bandwidth performance in a legacy DIP package (vsOPA606KP-3)
- Low input bias current supports high-impedance sources (vsOPA606KM)
- Higher slew rate preserves large-signal transitions (vsOPA606KM)
Ghi chú thiết kế
Keep the op-amp input, feedback, and gain-setting networks compact. The 8 pA input bias current of the OPA606KP can support high-impedance sources, but PCB contamination and leakage across a sensitive input may still dominate the total error. Use a guarded or well-cleaned input area, avoid long exposed traces, and connect the feedback return directly to the amplifier output to minimize parasitic coupling.
The OPA606KP supports ±5 V to ±18 V operation, giving a 10 V to 36 V total supply range. Decouple each supply rail close to the package with a suitable high-frequency bypass capacitor, and keep the power and ground return paths short. Verify actual input and output swing because rail-adjacent signals, startup behavior, and overload conditions can reduce the usable output range even when the total supply voltage is within specification.
Do not substitute an eight-pin amplifier solely by package count. OPA606KM has slightly different published bandwidth and slew-rate values, and the cross-reference information does not establish that its footprint and pinout match the installed 8-PDIP. Before replacement, compare the power pins, offset-null pins, input pins, output, feedback topology, supply range, stability, and operating temperature requirements from the manufacturer datasheet.
Thông tin tuân thủ
Compliance status was not established by the cited component pages. AEC-Q100 is marked not applicable because OPA606KP is a general-purpose analog amplifier rather than an automotive-qualified device.