PCA9535PWG4 - 16-Bit I/O Expander | Texas Instruments
MPN: PCA9535PWG4 ✓ Hoạt độngPCA9535PWG4 Tóm tắt
An I/O expander is an interface IC that translates a serial bus into additional digital input and output lines. The PCA9535 belongs to the parallel I/O port expander hierarchy within interface ICs, combining I2C control, SMBus compatibility, 16 independently configurable GPIOs, and an interrupt function. Its 400 kHz bus speed supports reliable communication with common embedded hosts while keeping the external wiring organized around a two-wire serial bus plus power and ground.
Each of the 16 ports can operate as an input or output, allowing the PCA9535PWG4 to control loads, read discrete signals, or combine both functions in one device. The serial interface provides a compact way to address and configure the ports from a microcontroller. Its 24-TSSOP package has a stated width of 4.40 mm and uses a gull-wing, surface-mount form factor, making it suitable for compact PCB layouts where a larger parallel-interface package would be inconvenient.
The PCA9535 family is designed for low-power embedded control because the serial interface reduces the number of host-controller connections required for external digital lines. A two-wire serial connection can replace a substantial group of direct host GPIO connections, while the expander still provides individual control of each line. The architecture is appropriate for systems in which the host must monitor switches, operate indicators, control relays, or read status signals distributed across a board.
Typical uses include industrial control modules, sensor-hub boards, programmable logic controllers, power-system monitoring, communication equipment, and compact embedded controllers. It is especially useful when the primary microcontroller has too few spare pins but the PCB can accommodate a small serial interface. Designers should also account for the I2C address configuration pins and the device's interrupt output when planning system startup and signal-change handling.
For PCB implementation, place the device close to the interfaces it serves and route I2C traces away from high-current switching paths. Confirm pull-up resistor values against the bus voltage, capacitance, clock rate, and the electrical characteristics of every connected device. The maximum operating supply is 5.5 V, so logic levels must remain compatible with the 24-TSSOP device and its I2C bus.
This product record combines the exact package and interface characteristics, source-backed pricing, compatible alternatives, and practical integration guidance. It also highlights the difference between electrically similar devices and true drop-in choices, helping engineers evaluate PCB reuse, bus compatibility, device addressing, and supply-temperature requirements before release to production.
Bộ thay thế dễ dàng lắp đặt cho PCA9535PWG4 — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với PCA9535PWG4 (cùng hình factor và footprint) — khác nhau ở Device Type.
PCA9535PW
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →PCA9535PWRG4
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
PCA9535PW,112
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
PCA9555PWG4
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
PCA9535ECDTR2G
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
PCA9535PWG4 Thông số kỹ thuật
| Device Type | 16-bit I/O expander |
| Number of I/O Lines | 16 lines |
| Serial Interface | I2C and SMBus |
| Maximum Serial Bus Frequency | 400 kHz |
| Maximum Supply Voltage | 5.5 V |
| Số lượng chân | 24 pins |
| Hộp | 24-TSSOP |
| Package Width | 4.40 mm |
| Terminal Form | Gull wing |
| Kiểu lắp đặt | Surface mount |
| Package Shape | Rectangular |
| Temperature Grade | Industrial |
| Encapsulation | Tube |
| Trạng thái RoHS | Yes |
| Low-Power Operation | Low-power I/O expansion |
| Product Description | Parallel I/O port with 16 general-purpose input/output lines |
Hướng dẫn cấu hình chân PCA9535PWG4 rectangular
Cấu hình chân cho PCA9535PWG4 (rectangular gói). Số thứ tự chân, chức năng và sơ đồ kết nối được xác định trong tài liệu thông số kỹ thuật của nhà sản xuất. Tham khảo nó để biết footprint và hướng dẫn hàn chính xác.
Không có dữ liệu chân cụ thể sẵn có cho PCA9535PWG4.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
PCA9535PWG4 phù hợp cho 6 Áp dụngs: Industrial Control Module, Sensor and Alarm Hub, Programmable Logic Controller Interface, Communication Equipment Status Control, LED and Relay Control, Embedded Power Monitoring.
Industrial Control Module
The PCA9535PWG4 fits industrial control modules that need more discrete inputs and outputs than the host controller can provide directly. Its 16 configurable lines can read switches and interlocks while controlling LEDs, relay drivers, or digital actuator enables, all through one I2C or SMBus connection operating up to 400 kHz. Placing the expander in a 24-TSSOP package preserves PCB area while separating remote I/O from the main controller. The design must account for the 5.5 V maximum device supply, compatible I2C logic levels, pull-up resistors, and the industrial temperature requirement. Interrupt support can also let the controller respond to a changed input rather than continuously polling all 16 ports.
Được đề xuất
Sensor and Alarm Hub
The PCA9535PWG4 is useful in sensor and alarm hubs that aggregate multiple digital status signals without consuming every GPIO on a microcontroller. Sixteen inputs can monitor door contacts, tamper sensors, card readers, relay feedback, or equipment-status flags, while remaining ports can drive local indicators. The 400 kHz I2C/SMBus rate provides a compact communication path for regularly reading port state, and the interrupt output supports event-driven monitoring when the host does not need continuous polling. Because the device is specified for an industrial temperature grade, it suits controlled industrial environments. System designers should verify address selection, interrupt polarity, pull-up sizing, and the voltage compatibility of every attached sensor.
Được đề xuất
Programmable Logic Controller Interface
The PCA9535PWG4 can extend the available digital interface of a programmable logic controller or compact embedded controller by adding 16 serial-controlled lines. This arrangement is valuable when a controller must operate relays, read discrete switches, or supervise multiple machine inputs while retaining most of its pins for other tasks. The 24-TSSOP package supports conventional surface-mount assembly, and the 16-bit parallel organization maps naturally to banks of sensors or actuators. At a maximum I2C clock frequency of 400 kHz, port updates can be coordinated with other low-speed bus devices. Engineers should place the device near the associated wiring, use appropriate transient protection for long external cables, and confirm that the controller's bus voltage and timing meet the PCA9535 electrical limits.
Được đề xuất
Communication Equipment Status Control
The PCA9535PWG4 fits communication equipment that requires distributed front-panel indicators, relay controls, or status inputs beyond the host processor's available pins. Sixteen I/O lines can operate panel LEDs, control equipment-enable signals, or read module-presence and fault indicators through an I2C/SMBus interface. Its 400 kHz bus operation is suitable for low- and moderate-rate management traffic, while the compact 24-TSSOP footprint supports space-constrained line cards. The interrupt function can notify the host of an external status transition and reduce unnecessary polling. Layout should keep the serial bus short, route sensitive communication lines separately, and use pull-up values that support the complete bus capacitance while remaining compatible with the logic voltage and 5.5 V maximum supply.
Được đề xuất
LED and Relay Control
The PCA9535PWG4 can control grouped LEDs and low-current relay-driver inputs where direct host-controller pins are limited. Ports may be configured as outputs for status lamps, optical-driver enables, or relay logic, while other ports can read returned or acknowledgment signals. The serial architecture allows the host to change several outputs through one bus transaction rather than dedicating one connection per line. The 24-TSSOP package supports dense PCB placement, although external drivers remain necessary when a load exceeds the port's current capability. Designers must confirm output-current limits, total supply-current budget, inductive-load protection, grounding, and logic-level compatibility. The stated 5.5 V maximum supply also requires careful coordination with relay-driver and LED circuitry.
Được đề xuất
Embedded Power Monitoring
The PCA9535PWG4 is appropriate for embedded power-monitoring boards that collect discrete enable, fault, presence, and reset signals. Sixteen inputs can monitor several power rails or subsystem states, while configurable outputs can control enable inputs or isolation devices. A 400 kHz I2C or SMBus connection allows a supervisory controller or microcontroller to read the port state efficiently, and interrupt signaling can indicate a transition without continuous polling. The industrial-grade designation supports use in controlled equipment environments. Because the target device has a 5.5 V maximum operating supply, its interface voltage must be reconciled with higher-voltage power-domain signals through suitable level translation or protection. The final design should also validate input thresholds, ground-reference relationships, and fault-state behavior.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho PCA9535PWG4 — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | PCA9535PW | PCA9535PWRG4 | PCA9535PW,112 | PCA9555PWG4 | PCA9535ECDTR2G |
|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | NXP Semiconductors | Texas Instruments | Texas Instruments |
| Package | 24-TSSOP | 24-TSSOP - same | 24-TSSOP - same | 24-TSSOP - same | 24-TSSOP - same | 24-TSSOP - same |
| Device Type | 16-bit I/O expander | 16-bit I/O expander | 16-bit I/O expander | 16-bit I/O expander | 16-bit I/O expander | 16-bit I/O expander |
| Number of I/O Lines | 16 lines | 16 lines | 16 lines | 16 lines | 16 lines | 16 lines |
| Serial Interface | I2C and SMBus | I2C and SMBus | I2C and SMBus | I2C and SMBus | I2C and SMBus | I2C and SMBus |
| Low-Power Operation | Yes | Yes | Yes | Yes | Yes | Yes |
Bảo phân biệt quan trọng
- Directly matches the principal PCA9535 interface characteristics (vsPCA9535PW,112)
- Maintains the 16-bit PCA9535 function in the same 24-TSSOP footprint (vsPCA9555PWG4)
- Uses the same core 16-bit, 400 kHz expansion function (vsPCA9535ECDTR2G)
Ghi chú thiết kế
Route the I2C clock and data traces as a short, matched pair and place the pull-up resistors near the device or bus master according to the complete bus topology. Keep switching-converter paths, motor outputs, and high-current LED drivers away from the serial interface. The PCA9535PWG4 supports up to 400 kHz, but practical layout must also preserve signal integrity across the full bus length and number of connected devices.
Validate every port state before connecting external circuitry because an I/O expander is powered from a constrained 5.5 V maximum device supply. Confirm the host's I2C logic voltage, pull-up voltage, output-current limits, and ground reference before connection. If controlled loads can back-feed an unpowered expander, use suitable isolation or ensure that all rails and pull-ups obey the manufacturer's sequencing requirements.
Do not treat a matching 24-TSSOP footprint as proof that every alternative has identical software behavior. Review address-selection pins, configuration registers, interrupt polarity, electrical timing, temperature range, and absolute maximum ratings for each candidate. A PCA9555-family device retains the 16-bit expansion concept but uses a different feature set and register architecture, so existing firmware may require modification.
Choose pull-up values from the bus capacitance and voltage rather than using a fixed value across every design. Check the rise time against the 400 kHz operating limit and ensure the pull-up does not exceed the sink-current capability of the host or expander. When the bus includes multiple PCA9535 devices, document each address configuration and avoid duplicate addresses on the same controller segment.
Thông tin tuân thủ
The product listing identifies RoHS status as Yes. No separate REACH, halogen-free, conflict-minerals, or automotive qualification information was identified.