Texas Instruments

PCF8574ANG4 - 8-Bit 100kHz I2C I/O Expander | Texas Instruments

MPN: PCF8574ANG4 ✓ Hoạt động
16-pin PDIP Package 100 kHz Speed
MOQ: 1 |

PCF8574ANG4 Tóm tắt

Texas Instruments PCF8574ANG4 is an 8-bit I2C I/O expander operating at a 100 kHz bus frequency and packaged in a 16-pin PDIP enclosure measuring 0.300 inches with 7.62 mm lead spacing. It adds eight general-purpose input/output lines to a host controller while using an I2C connection for register communication.

An I/O expander is a semiconductor interface device that extends the number of digital lines available to a microcontroller or other embedded controller. It belongs to the I/O expander category within interface ICs, where the device translates serial bus commands into parallel input or output states. This approach reduces direct GPIO requirements and is especially useful when a host controller has limited connector pins.

The PCF8574ANG4 provides eight I/O positions and uses a two-wire I2C interface with a maximum stated bus frequency of 100 kHz. Its 16-pin PDIP package supports conventional through-hole PCB assembly and is identifiable by its 0.300-inch body width and 7.62 mm lead pitch. These mechanical dimensions help engineers match the component to an existing footprint and connector arrangement.

Operationally, the expander is intended to read or control external digital lines while the host processor manages address selection, register access, and application behavior. I2C communication allows the host to update output states or sample input states over the serial bus, reducing the number of wires needed between the controller and remote digital hardware. The 100 kHz operating limit should be considered when designing the bus topology.

Typical uses include keypad and control-panel interfaces, relay and indicator outputs, digital sensor gathering, industrial automation modules, embedded control boards, and compact consumer accessories. The eight available lines make the device especially practical where modest GPIO expansion is required rather than a large bank of isolated inputs or high-speed outputs.

For PCB implementation, confirm the 16-pin PDIP footprint and 7.62 mm pitch against the mechanical drawing before layout. I2C pull-up requirements, bus capacitance, address configuration, and the maximum supported bus frequency must be evaluated in the complete circuit. This page combines package, interface, application, replacement, and design information for faster component selection.

Bộ thay thế dễ dàng lắp đặt cho PCF8574ANG4 — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.

Các biến thể trong loạt này

Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với PCF8574ANG4 (cùng hình factor và footprint) — khác nhau ở Device Type, Interface, Package, Supply Voltage Range.

Texas Instruments
Interface: I2C two-line bidirectional bus
Package: 16-pin PDIP
Supply Voltage Range: 2.5V to 6V
So sánh với PCF8574ANG4 →
Texas Instruments
Device Type: 8-bit I/O expander
Interface: I2C
Package: 16-DIP (0.300 inch, 7.62 mm)
So sánh với PCF8574ANG4 →

PCF8574N

✅ Drop-In
Texas Instruments
📦 16-pin PDIP
8-bit I2C I/O expander · 2.5V to 6V · 100kHz · 8 · I2C two-line bidirectional bus · Interrupt output · 16-pin PDIP · Through-hole

Liên hệ để biết giá

Xem tài liệu →

PCF8574AN

✅ Drop-In
Texas Instruments
📦 16-pin PDIP
Thông số tương thích

Liên hệ để biết giá

PCF8574NG4

✅ Drop-In
Texas Instruments
📦 16-pin PDIP
8-bit I/O expander · I2C · 100 kHz · 2.5 V to 6 V · 8 lines · 8-bit quasi-bidirectional · Two-line bidirectional · 16-DIP (0.300 inch, 7.62 mm)

Liên hệ để biết giá

Xem tài liệu →

PCF8574P,112

✅ Drop-In
📦 16-pin PDIP
The 8-bit I/O count and 100 kHz I2C frequency match 100%; cross-reference data identifies the same DIP-16 function, while suffix-specific electrical and temperature details still require validation.

📋 Tham chiếu thay thế (không có trong danh mục)

PCF8574AP,112

✅ Drop-In
📦 16-pin PDIP
The 8-bit I/O count, 100 kHz I2C rating, and DIP-16 package match; the A suffix can denote a distinct grade, so operating-temperature and qualification conditions must be checked.

📋 Tham chiếu thay thế (không có trong danh mục)

PCF8574ANG4 Thông số kỹ thuật

Device Type 8-bit I2C I/O expander
Number of I/O Lines 8 lines
Serial Interface I2C
Maximum I2C Bus Frequency 100 kHz
Input/Output Configuration Bidirectional I/O, 8 lines
Package Type 16-pin PDIP
Package Body Width 0.300 inch
Lead Pitch 7.62 mm
Kiểu lắp đặt Through-hole
Trạng thái RoHS RoHS3 compliant

Hướng dẫn cấu hình chân PCF8574ANG4 0.300 inch

Cấu hình chân cho PCF8574ANG4 (0.300 inch gói). Số thứ tự chân, chức năng và sơ đồ kết nối được xác định trong tài liệu thông số kỹ thuật của nhà sản xuất. Tham khảo nó để biết footprint và hướng dẫn hàn chính xác.

Bảng cấu hình chân 0.300 inch cho PCF8574ANG4

Không có dữ liệu chân cụ thể sẵn có cho PCF8574ANG4.

Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.

Ứng dụng tiêu biểu

PCF8574ANG4 phù hợp cho 6 Áp dụngs: Industrial Control Panels, Relay and Indicator Control, Keypad and Human-Interface Expansion, Digital Sensor Aggregation, Embedded Accessory and Appliance Controls, Educational and Prototype GPIO Expansion.

🏭

Industrial Control Panels

PCF8574ANG4 fits compact industrial control panels that need several operator inputs, status indicators, or discrete command outputs without consuming most of a controller's GPIO pins. The host processor uses the I2C interface at up to 100 kHz to read panel states and update output states while the eight parallel lines connect to switches, lamps, or relay-command circuits. This arrangement simplifies point-to-point wiring, although the 100 kHz bus limit and the exact suffix's operating-temperature rating should be checked against factory and industrial environmental requirements.

⚡

Relay and Indicator Control

The eight I/O lines of PCF8574ANG4 can reduce the number of host-controller connections needed for relay-command and indicator-control boards. A microcontroller writes the desired output states through the 100 kHz I2C bus, allowing the expander to interface with external driver circuitry while preserving GPIO pins for other tasks. The device is best suited to low-speed switching of discrete loads rather than high-frequency pulse-width modulation; relay snubbers, isolation, driver transistors, and suitable flyback paths must be handled by the surrounding circuit.

🧩

Keypad and Human-Interface Expansion

PCF8574ANG4 is useful in keypad, menu-key, and simple human-interface designs because eight digital lines can cover a small set of switches without requiring one microcontroller pin per key. The controller scans or updates the lines through I2C at up to 100 kHz, while the expander provides a parallel interface close to the switch hardware. For debouncing, key-state decoding, and electrical protection, use suitable external components and firmware logic rather than assuming that every implementation requires the maximum bus rate.

🔧

Digital Sensor Aggregation

PCF8574ANG4 can collect several slow-changing digital status signals from sensors, limit switches, interlocks, or module status pins. The I2C master reads the expander's eight lines through a bus limited to 100 kHz, which suits supervisory signals rather than high-speed waveforms. Keeping the serial bus away from noisy analog or switching paths helps maintain signal integrity. The final design should also confirm that each attached signal remains within the device's input and output electrical limits.

📱

Embedded Accessory and Appliance Controls

PCF8574ANG4 is practical in compact embedded accessories that need several buttons, mode indicators, latches, or appliance-control signals. Its 16-pin PDIP package is convenient for through-hole modules and prototypes, while the 8-bit parallel interface reduces wiring between a controller board and a front-panel or auxiliary board. The 100 kHz I2C limit is adequate for command and status traffic but not for continuous high-throughput transfer. Firmware must define the electrical direction and pull-up behavior of each line before normal operation.

🔧

Educational and Prototype GPIO Expansion

PCF8574ANG4 provides a straightforward way to prototype additional digital inputs and outputs around a small microcontroller. Because the device uses only the I2C interface for register communication and exposes eight parallel lines, it is useful for teaching, breadboard-based controllers, and early firmware development. Designers should use the manufacturer's 16-pin PDIP pinout, include appropriate pull-ups, and avoid driving a line externally while the firmware has configured it as an output. This application remains within the stated 100 kHz I2C operating limit.

What is the PCF8574ANG4 and what does it do?
The PCF8574ANG4 is an 8-bit I2C I/O expander that adds eight general-purpose digital lines to a host controller. According to the Texas Instruments PCF8574A datasheet, it supports a maximum I2C bus frequency of 100 kHz and is offered in a 16-pin PDIP package. It is useful when a microcontroller, embedded controller, or interface device has too few direct GPIO pins for switches, indicators, relays, or digital sensors.
How many I/O pins does the PCF8574ANG4 provide?
The PCF8574ANG4 provides eight general-purpose I/O lines in a 16-pin PDIP package. The PCF8574A datasheet identifies the device as a remote 8-bit I/O expander for an I2C bus, and distributor listings describe it as an I/O expander with eight I/O positions. The package also includes power, ground, clock, data, and address-control connections in addition to the eight I/O lines.
What is the maximum I2C bus frequency of PCF8574ANG4?
The PCF8574ANG4 supports I2C operation up to 100 kHz. The Texas Instruments PCF8574A datasheet and the manufacturer listing identify the device as an I/O expander with a 100 kHz bus frequency. Keep the complete bus within that limit after accounting for bus capacitance, pull-up resistance, clock rise and fall times, and the electrical characteristics of every controller and peripheral attached to the same I2C bus.
Where can I download the PCF8574ANG4 datasheet PDF?
The PCF8574ANG4 datasheet PDF is available from Texas Instruments at https://www.ti.com/lit/ds/symlink/pcf8574a.pdf. The document is the PCF8574A family datasheet covering the remote 8-bit I/O expander used for I2C buses. Use its pin description table, electrical characteristics, and application information when assigning the sixteen PDIP leads and checking the power, interface, and logic-level requirements.
Where can I find the PCF8574ANG4 pinout?
The authoritative PCF8574ANG4 pin assignment is shown in the pin configuration and pin description tables of the Texas Instruments PCF8574A datasheet. The component uses a 16-pin PDIP arrangement with eight I/O lines plus the associated power, ground, clock, data, and address-selection connections. Use the manufacturer's numbering diagram rather than relying on a generic DIP drawing, because the notch and pin-one orientation determine the correct PCB connection.
What package and lead spacing does the PCF8574ANG4 use?
The PCF8574ANG4 uses a 16-pin PDIP package with a stated body width of 0.300 inch and a 7.62 mm lead pitch. The Texas Instruments component listing identifies the package as 16-DIP, while the distributor description specifies 0.300-inch width and 7.62 mm spacing. These dimensions allow direct comparison with the target PCB footprint before assembly, particularly for through-hole designs assembled outside automated surface-mount processes.
Is PCF8574ANG4 the same as PCF8574AN?
PCF8574ANG4 and PCF8574AN are closely related orderable forms of the PCF8574A device, but ordering suffixes can encode packaging, temperature, or other qualification differences. The available comparison information identifies PCF8574AN as an 8-bit, 100 kHz I2C expander in a PDIP-16 package. Confirm the suffix-specific temperature range, shipping form, and marking in the manufacturer documentation before treating either orderable MPN as a substitute.
What can replace the PCF8574ANG4?
The PCF8574ANG4 can be replaced only after confirming identical package geometry, pin functions, electrical limits, and operating-temperature requirements. Relevant 16-pin candidates identified in cross-reference results include PCF8574N, PCF8574AN, PCF8574NG4, PCF8574P,112, and PCF8574AP,112. These are candidate drop-ins rather than unconditional approvals; use the Request a Quote form on this page for sourcing, then validate the selected suffix against the manufacturer datasheet.
PCF8574ANG4 vs PCF8574N: which one should be selected?
PCF8574ANG4 is the better choice when its suffix-specific ordering, temperature, and packaging requirements match the design, while PCF8574N is a candidate when its corresponding grade and configuration satisfy the same requirements. Both belong to the 8-bit, 100 kHz I2C expander family in a 16-pin PDIP format according to the cross-reference information. The decisive differences are ordering-suffix specifications rather than basic I/O count or bus frequency.
PCF8574ANG4 vs NXP PCF8574P,112: is the NXP part pin-compatible?
PCF8574P,112 is a candidate direct replacement because cross-reference information identifies it as an 8-bit, 100 kHz I2C expander in a DIP-16 package. However, a drop-in decision must also confirm pin naming, address behavior, electrical characteristics, and temperature range for the exact NXP suffix. The 8-bit and 100 kHz headline specifications align, while suffix-level differences remain the key items to verify before substitution.
When should I choose PCF8574ANG4 instead of a larger I/O expander?
Choose PCF8574ANG4 when the design needs eight general-purpose digital lines and a 100 kHz I2C connection rather than a larger parallel I/O count. It is well matched to compact control panels, keypad interfaces, relay banks, and small embedded systems where conserving microcontroller GPIO is important. Select a larger expander only when the required line count, addressing, interrupt behavior, or input/output voltage cannot be met by the eight-line device.
Is PCF8574ANG4 suitable for industrial control and automation?
PCF8574ANG4 is suitable for many industrial control tasks that require a small number of low-speed digital lines, such as status inputs, indicator outputs, and relay-control signals. Its 100 kHz I2C limit makes it appropriate for supervisory rather than high-speed signal routing. Industrial qualification still depends on the exact suffix's temperature rating, electrical limits, quality status, and the environmental requirements of the finished equipment.
How should pull-ups and layout be handled for PCF8574ANG4?
Place the I2C pull-up network near the active bus nodes and route SCL and SDA as short, controlled traces away from noisy switching paths. The resistor values must support the intended bus voltage while meeting the PCF8574A datasheet's sink-current and rise-time limits. The through-hole package also requires careful pin-one orientation and mechanical clearance, so verify the manufacturer's PDIP footprint before finalizing the PCB.
Where can I buy PCF8574ANG4 and check its availability?
Use the Request a Quote form on this page to request the current PCF8574ANG4 price, stock position, minimum order quantity, and delivery schedule. The manufacturer listing identifies the part as an 8-bit, 100 kHz I2C expander in a 16-pin PDIP package, while distributor inventory changes continuously. Quote requests provide the appropriate channel for a current commercial commitment without relying on a stale availability statement.
What is the lead time for PCF8574ANG4?
The current lead time for PCF8574ANG4 should be confirmed through the Request a Quote form on this page. Lead time can vary with the requested quantity, package form, inventory position, and production schedule. The part is identified as a 16-pin PDIP Texas Instruments I/O expander, but those identifying characteristics do not establish a fixed delivery interval; request a written quotation for the exact order quantity.

Dữ liệu tham khảo kỹ thuật cho PCF8574ANG4 — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.

Hướng dẫn chọn lựa

Choose PCF8574ANG4 when the PCB requires a 16-pin PDIP footprint, eight general-purpose I/O lines, and an I2C bus no faster than 100 kHz. It is a sensible fit for control panels, keypad interfaces, relay-command boards, and compact embedded accessories where conserving host-controller GPIO is useful. Consider PCF8574N, PCF8574AN, or PCF8574NG4 when an existing Texas Instruments supply plan favors another suffix, after confirming its temperature, packaging, and qualification details. PCF8574P,112 and PCF8574AP,112 are cross-brand candidates for designs that can use NXP sourcing, but their exact electrical limits, address behavior, pin assignments, and operating-temperature ratings must match the design. Do not select any candidate solely from the common 8-bit and 100 kHz headline ratings: verify the suffix-specific datasheet and production requirements before releasing a substitution.

So sánh với các sản phẩm thay thế

Tham số Sản phẩm này PCF8574N PCF8574AN PCF8574NG4 PCF8574P,112 PCF8574AP,112
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments NXP Semiconductors NXP Semiconductors
Package 16-pin PDIP 16-pin PDIP 16-pin PDIP 16-pin PDIP 16-pin PDIP 16-pin PDIP
Device Type 8-bit I2C I/O expander 8-bit I2C I/O expander 8-bit I2C I/O expander 8-bit I2C I/O expander 8-bit I2C I/O expander 8-bit I2C I/O expander
Number of I/O Lines 8 lines 8 lines 8 lines 8 lines 8 lines 8 lines
Maximum I2C Bus Frequency 100 kHz 100 kHz 100 kHz 100 kHz 100 kHz 100 kHz
Interface I2C I2C I2C I2C I2C I2C

Bảo phân biệt quan trọng

  • Directly matches the requested 8-bit and 100 kHz operating profile (vsPCF8574P,112)
  • Uses the same core interface and line count as the original Texas Instruments family (vsPCF8574AN)
  • Provides the expected eight-line expansion without requiring a larger parallel interface (vsPCF8574AP,112)

Ghi chú thiết kế

Verify the 16-pin PDIP footprint, 7.62 mm lead pitch, and pin-one orientation against the manufacturer's package drawing before PCB release. The PCF8574ANG4 is a through-hole device, so account for lead diameter, drill size, pad clearance, and component-body height in the mechanical layout. Use a visible pin-one mark and avoid placing tall or heat-generating parts where they interfere with the expander body.

Keep the I2C clock and data traces short, route them away from switching nodes, and use pull-up resistors that satisfy the bus voltage and timing requirements at the maximum 100 kHz operating frequency. Check the complete network's effective capacitance, pull-up current, clock rise time, and available sink current. Where multiple expanders share the bus, review address selection and ensure the combined bus loading does not exceed the slowest participant.

Treat each of the eight I/O lines as a shared resource and avoid simultaneous external drive and output-mode operation. Firmware should establish the intended input or output direction before applying an external signal, and unused lines should be configured according to the manufacturer's recommended state. Because the device is identified as a 100 kHz I2C expander, do not assume it supports faster bus modes used by newer peripherals.

Follow the manufacturer's power and decoupling recommendations when connecting the device to a mixed digital system. Place local bypass capacitance close to the supply and ground pins, and account for switching current from attached I2C devices when estimating rail noise. If the eight lines drive external circuitry through transistors or relay drivers, calculate those loads separately because the expander's own supply demand alone does not represent the total board load.

Thông tin tuân thủ

RoHS
Compliant
REACH
Unknown
AEC-Q100
Unknown
Không chì
Unknown
Không halogen
Unknown
Khoáng vật xung đột
Unknown

The component listing identifies PCF8574ANG4 as RoHS3 compliant. No verified information was available for REACH, AEC-Q100, lead-free status, halogen-free status, or conflict-minerals compliance.

Dữ liệu được xác minh vào: 2026-11-14 — dữ liệu được xác minh và quản lý bởi đội ngũ kỹ thuật phần cứng của XAIPART

Tìm kiếm liên quan

pcf8574an datasheet PCF8574ANG4 datasheet PCF8574ANG4 pinout PCF8574ANG4 datasheet pdf PCF8574ANG4 equivalent PCF8574ANG4 replacement PCF8574ANG4 cross reference PCF8574ANG4 vs PCF8574N PCF8574ANG4 DIP-16 footprint PCF8574ANG4 8-bit 100kHz PCF8574ANG4 price PCF8574ANG4 stock Texas Instruments PCF8574ANG4 PCF8574ANG4 I2C GPIO expander

Các bộ phận và thuật ngữ liên quan

Texas Instruments PCF8574ANG4 PCF8574A PCF8574N PCF8574AN PCF8574NG4 PCF8574P,112 PCF8574AP,112 NXP Semiconductors I/O expander interface IC I2C two-wire serial bus general-purpose input/output GPIO expansion remote 8-bit I/O expander PDIP-16 16-pin PDIP through-hole package 7.62 mm lead pitch 100 kHz I2C bus control panel keypad interface relay control digital sensor aggregation
Báo giá nhanh RFQ
Hãy điền đầy đủ thông tin — đội ngũ bán hàng của chúng tôi sẽ phản hồi trong vòng 24 giờ
Mã sản phẩm Nhà sản xuất Kiểu đóng gói QTY Giá mục tiêu Phụ
✓
Báo giá đã gửi!

Chúng tôi sẽ trả lời email của bạn trong vòng 24 giờ

1
RFQ đã gửi
2
Phiếu báo giá nhận được
3
Đặt hàng thành công
4
Thanh toán
5
Đã gửi
6
Đã giao hàng
Xem chi tiết RFQ