PCF8574ANG4 - 8-Bit 100kHz I2C I/O Expander | Texas Instruments
MPN: PCF8574ANG4 ✓ 啟用中PCF8574ANG4 概覽
An I/O expander is a semiconductor interface device that extends the number of digital lines available to a microcontroller or other embedded controller. It belongs to the I/O expander category within interface ICs, where the device translates serial bus commands into parallel input or output states. This approach reduces direct GPIO requirements and is especially useful when a host controller has limited connector pins.
The PCF8574ANG4 provides eight I/O positions and uses a two-wire I2C interface with a maximum stated bus frequency of 100 kHz. Its 16-pin PDIP package supports conventional through-hole PCB assembly and is identifiable by its 0.300-inch body width and 7.62 mm lead pitch. These mechanical dimensions help engineers match the component to an existing footprint and connector arrangement.
Operationally, the expander is intended to read or control external digital lines while the host processor manages address selection, register access, and application behavior. I2C communication allows the host to update output states or sample input states over the serial bus, reducing the number of wires needed between the controller and remote digital hardware. The 100 kHz operating limit should be considered when designing the bus topology.
Typical uses include keypad and control-panel interfaces, relay and indicator outputs, digital sensor gathering, industrial automation modules, embedded control boards, and compact consumer accessories. The eight available lines make the device especially practical where modest GPIO expansion is required rather than a large bank of isolated inputs or high-speed outputs.
For PCB implementation, confirm the 16-pin PDIP footprint and 7.62 mm pitch against the mechanical drawing before layout. I2C pull-up requirements, bus capacitance, address configuration, and the maximum supported bus frequency must be evaluated in the complete circuit. This page combines package, interface, application, replacement, and design information for faster component selection.
直接替換替代品,適用於 PCF8574ANG4 — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: PCF8574ANG4 (相同外形與佔位) — 差異在於 Device Type, Interface, Package, Supply Voltage Range.
PCF8574N
✅ 直接替換聯絡詢價
查看資料表 →PCF8574NG4
✅ 直接替換聯絡詢價
查看資料表 →PCF8574P,112
✅ 直接替換📋 參考替代品(不在目錄中)
PCF8574AP,112
✅ 直接替換📋 參考替代品(不在目錄中)
PCF8574ANG4 規格
| Device Type | 8-bit I2C I/O expander |
| Number of I/O Lines | 8 lines |
| Serial Interface | I2C |
| Maximum I2C Bus Frequency | 100 kHz |
| Input/Output Configuration | Bidirectional I/O, 8 lines |
| Package Type | 16-pin PDIP |
| Package Body Width | 0.300 inch |
| Lead Pitch | 7.62 mm |
| 安裝方式 | Through-hole |
| RoHS 狀態 | RoHS3 compliant |
PCF8574ANG4 0.300 inch 腳位配置指南
PCF8574ANG4(0.300 inch 封裝)的腳位配置。 腳位編號、功能與連接圖定義於製造商資料手冊中。請參閱該手冊以取得確切的封裝尺寸與焊接指引。
無詳細腳位定義資料: PCF8574ANG4.
請參閱 資料表 以查看完整腳位配置。
典型應用
PCF8574ANG4 適用於 6 應用s: Industrial Control Panels, Relay and Indicator Control, Keypad and Human-Interface Expansion, Digital Sensor Aggregation, Embedded Accessory and Appliance Controls, Educational and Prototype GPIO Expansion.
Industrial Control Panels
PCF8574ANG4 fits compact industrial control panels that need several operator inputs, status indicators, or discrete command outputs without consuming most of a controller's GPIO pins. The host processor uses the I2C interface at up to 100 kHz to read panel states and update output states while the eight parallel lines connect to switches, lamps, or relay-command circuits. This arrangement simplifies point-to-point wiring, although the 100 kHz bus limit and the exact suffix's operating-temperature rating should be checked against factory and industrial environmental requirements.
推薦
Relay and Indicator Control
The eight I/O lines of PCF8574ANG4 can reduce the number of host-controller connections needed for relay-command and indicator-control boards. A microcontroller writes the desired output states through the 100 kHz I2C bus, allowing the expander to interface with external driver circuitry while preserving GPIO pins for other tasks. The device is best suited to low-speed switching of discrete loads rather than high-frequency pulse-width modulation; relay snubbers, isolation, driver transistors, and suitable flyback paths must be handled by the surrounding circuit.
推薦
Keypad and Human-Interface Expansion
PCF8574ANG4 is useful in keypad, menu-key, and simple human-interface designs because eight digital lines can cover a small set of switches without requiring one microcontroller pin per key. The controller scans or updates the lines through I2C at up to 100 kHz, while the expander provides a parallel interface close to the switch hardware. For debouncing, key-state decoding, and electrical protection, use suitable external components and firmware logic rather than assuming that every implementation requires the maximum bus rate.
推薦
Digital Sensor Aggregation
PCF8574ANG4 can collect several slow-changing digital status signals from sensors, limit switches, interlocks, or module status pins. The I2C master reads the expander's eight lines through a bus limited to 100 kHz, which suits supervisory signals rather than high-speed waveforms. Keeping the serial bus away from noisy analog or switching paths helps maintain signal integrity. The final design should also confirm that each attached signal remains within the device's input and output electrical limits.
推薦
Embedded Accessory and Appliance Controls
PCF8574ANG4 is practical in compact embedded accessories that need several buttons, mode indicators, latches, or appliance-control signals. Its 16-pin PDIP package is convenient for through-hole modules and prototypes, while the 8-bit parallel interface reduces wiring between a controller board and a front-panel or auxiliary board. The 100 kHz I2C limit is adequate for command and status traffic but not for continuous high-throughput transfer. Firmware must define the electrical direction and pull-up behavior of each line before normal operation.
推薦
Educational and Prototype GPIO Expansion
PCF8574ANG4 provides a straightforward way to prototype additional digital inputs and outputs around a small microcontroller. Because the device uses only the I2C interface for register communication and exposes eight parallel lines, it is useful for teaching, breadboard-based controllers, and early firmware development. Designers should use the manufacturer's 16-pin PDIP pinout, include appropriate pull-ups, and avoid driving a line externally while the firmware has configured it as an output. This application remains within the stated 100 kHz I2C operating limit.
推薦
推薦產品摘要
工程參考資料,適用於 PCF8574ANG4 — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | PCF8574N | PCF8574AN | PCF8574NG4 | PCF8574P,112 | PCF8574AP,112 |
|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | NXP Semiconductors | NXP Semiconductors |
| Package | 16-pin PDIP | 16-pin PDIP | 16-pin PDIP | 16-pin PDIP | 16-pin PDIP | 16-pin PDIP |
| Device Type | 8-bit I2C I/O expander | 8-bit I2C I/O expander | 8-bit I2C I/O expander | 8-bit I2C I/O expander | 8-bit I2C I/O expander | 8-bit I2C I/O expander |
| Number of I/O Lines | 8 lines | 8 lines | 8 lines | 8 lines | 8 lines | 8 lines |
| Maximum I2C Bus Frequency | 100 kHz | 100 kHz | 100 kHz | 100 kHz | 100 kHz | 100 kHz |
| Interface | I2C | I2C | I2C | I2C | I2C | I2C |
主要差異化特點
- Directly matches the requested 8-bit and 100 kHz operating profile (對比PCF8574P,112)
- Uses the same core interface and line count as the original Texas Instruments family (對比PCF8574AN)
- Provides the expected eight-line expansion without requiring a larger parallel interface (對比PCF8574AP,112)
設計說明
Verify the 16-pin PDIP footprint, 7.62 mm lead pitch, and pin-one orientation against the manufacturer's package drawing before PCB release. The PCF8574ANG4 is a through-hole device, so account for lead diameter, drill size, pad clearance, and component-body height in the mechanical layout. Use a visible pin-one mark and avoid placing tall or heat-generating parts where they interfere with the expander body.
Keep the I2C clock and data traces short, route them away from switching nodes, and use pull-up resistors that satisfy the bus voltage and timing requirements at the maximum 100 kHz operating frequency. Check the complete network's effective capacitance, pull-up current, clock rise time, and available sink current. Where multiple expanders share the bus, review address selection and ensure the combined bus loading does not exceed the slowest participant.
Treat each of the eight I/O lines as a shared resource and avoid simultaneous external drive and output-mode operation. Firmware should establish the intended input or output direction before applying an external signal, and unused lines should be configured according to the manufacturer's recommended state. Because the device is identified as a 100 kHz I2C expander, do not assume it supports faster bus modes used by newer peripherals.
Follow the manufacturer's power and decoupling recommendations when connecting the device to a mixed digital system. Place local bypass capacitance close to the supply and ground pins, and account for switching current from attached I2C devices when estimating rail noise. If the eight lines drive external circuitry through transistors or relay drivers, calculate those loads separately because the expander's own supply demand alone does not represent the total board load.
合規資訊
The component listing identifies PCF8574ANG4 as RoHS3 compliant. No verified information was available for REACH, AEC-Q100, lead-free status, halogen-free status, or conflict-minerals compliance.