PCF8574ANG4 - 8-Bit 100kHz I2C I/O Expander | Texas Instruments
MPN: PCF8574ANG4 ✓ فعالPCF8574ANG4 نمای کلی
An I/O expander is a semiconductor interface device that extends the number of digital lines available to a microcontroller or other embedded controller. It belongs to the I/O expander category within interface ICs, where the device translates serial bus commands into parallel input or output states. This approach reduces direct GPIO requirements and is especially useful when a host controller has limited connector pins.
The PCF8574ANG4 provides eight I/O positions and uses a two-wire I2C interface with a maximum stated bus frequency of 100 kHz. Its 16-pin PDIP package supports conventional through-hole PCB assembly and is identifiable by its 0.300-inch body width and 7.62 mm lead pitch. These mechanical dimensions help engineers match the component to an existing footprint and connector arrangement.
Operationally, the expander is intended to read or control external digital lines while the host processor manages address selection, register access, and application behavior. I2C communication allows the host to update output states or sample input states over the serial bus, reducing the number of wires needed between the controller and remote digital hardware. The 100 kHz operating limit should be considered when designing the bus topology.
Typical uses include keypad and control-panel interfaces, relay and indicator outputs, digital sensor gathering, industrial automation modules, embedded control boards, and compact consumer accessories. The eight available lines make the device especially practical where modest GPIO expansion is required rather than a large bank of isolated inputs or high-speed outputs.
For PCB implementation, confirm the 16-pin PDIP footprint and 7.62 mm pitch against the mechanical drawing before layout. I2C pull-up requirements, bus capacitance, address configuration, and the maximum supported bus frequency must be evaluated in the complete circuit. This page combines package, interface, application, replacement, and design information for faster component selection.
جایگزینهای drop-in برای PCF8574ANG4 — همان پکیج، سازگار پینبهپین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.
گونهها در این سری
مدلهای همسری که جایگزین مستقیم هستند برای PCF8574ANG4 (همان فرمفاکتور و فوتپرینت) — متفاوت در Device Type, Interface, Package, Supply Voltage Range.
PCF8574N
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←PCF8574NG4
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←PCF8574P,112
✅ جایگزین مستقیم📋 جایگزین مرجع (خارج از کاتالوگ)
PCF8574AP,112
✅ جایگزین مستقیم📋 جایگزین مرجع (خارج از کاتالوگ)
PCF8574ANG4 مشخصات
| Device Type | 8-bit I2C I/O expander |
| Number of I/O Lines | 8 lines |
| Serial Interface | I2C |
| Maximum I2C Bus Frequency | 100 kHz |
| Input/Output Configuration | Bidirectional I/O, 8 lines |
| Package Type | 16-pin PDIP |
| Package Body Width | 0.300 inch |
| Lead Pitch | 7.62 mm |
| سبک نصب | Through-hole |
| وضعیت RoHS | RoHS3 compliant |
راهنمای پیکربندی پین PCF8574ANG4 0.300 inch
پیکربندی پین برای PCF8574ANG4 (پکیج 0.300 inch). شمارهگذاری پایهها، عملکردها و نمودارهای اتصال در دیتاشیت سازنده تعریف شده است. برای footprint دقیق و دستورالعملهای لحیمکاری به آن مراجعه کنید.
داده پینآوت تفصیلی موجود نیست برای PCF8574ANG4.
به دیتاشیت برای پیکربندی کامل پینها.
کاربردهای معمول
PCF8574ANG4 مناسب است برای 6 کاربردs: Industrial Control Panels, Relay and Indicator Control, Keypad and Human-Interface Expansion, Digital Sensor Aggregation, Embedded Accessory and Appliance Controls, Educational and Prototype GPIO Expansion.
Industrial Control Panels
PCF8574ANG4 fits compact industrial control panels that need several operator inputs, status indicators, or discrete command outputs without consuming most of a controller's GPIO pins. The host processor uses the I2C interface at up to 100 kHz to read panel states and update output states while the eight parallel lines connect to switches, lamps, or relay-command circuits. This arrangement simplifies point-to-point wiring, although the 100 kHz bus limit and the exact suffix's operating-temperature rating should be checked against factory and industrial environmental requirements.
پیشنهادی
Relay and Indicator Control
The eight I/O lines of PCF8574ANG4 can reduce the number of host-controller connections needed for relay-command and indicator-control boards. A microcontroller writes the desired output states through the 100 kHz I2C bus, allowing the expander to interface with external driver circuitry while preserving GPIO pins for other tasks. The device is best suited to low-speed switching of discrete loads rather than high-frequency pulse-width modulation; relay snubbers, isolation, driver transistors, and suitable flyback paths must be handled by the surrounding circuit.
پیشنهادی
Keypad and Human-Interface Expansion
PCF8574ANG4 is useful in keypad, menu-key, and simple human-interface designs because eight digital lines can cover a small set of switches without requiring one microcontroller pin per key. The controller scans or updates the lines through I2C at up to 100 kHz, while the expander provides a parallel interface close to the switch hardware. For debouncing, key-state decoding, and electrical protection, use suitable external components and firmware logic rather than assuming that every implementation requires the maximum bus rate.
پیشنهادی
Digital Sensor Aggregation
PCF8574ANG4 can collect several slow-changing digital status signals from sensors, limit switches, interlocks, or module status pins. The I2C master reads the expander's eight lines through a bus limited to 100 kHz, which suits supervisory signals rather than high-speed waveforms. Keeping the serial bus away from noisy analog or switching paths helps maintain signal integrity. The final design should also confirm that each attached signal remains within the device's input and output electrical limits.
پیشنهادی
Embedded Accessory and Appliance Controls
PCF8574ANG4 is practical in compact embedded accessories that need several buttons, mode indicators, latches, or appliance-control signals. Its 16-pin PDIP package is convenient for through-hole modules and prototypes, while the 8-bit parallel interface reduces wiring between a controller board and a front-panel or auxiliary board. The 100 kHz I2C limit is adequate for command and status traffic but not for continuous high-throughput transfer. Firmware must define the electrical direction and pull-up behavior of each line before normal operation.
پیشنهادی
Educational and Prototype GPIO Expansion
PCF8574ANG4 provides a straightforward way to prototype additional digital inputs and outputs around a small microcontroller. Because the device uses only the I2C interface for register communication and exposes eight parallel lines, it is useful for teaching, breadboard-based controllers, and early firmware development. Designers should use the manufacturer's 16-pin PDIP pinout, include appropriate pull-ups, and avoid driving a line externally while the firmware has configured it as an output. This application remains within the stated 100 kHz I2C operating limit.
پیشنهادی
خلاصه محصولات پیشنهادی
دادههای مرجع مهندسی برای PCF8574ANG4 — مقایسه، راهنمای طراحی و اطلاعات انطباق.
راهنمای انتخاب
مقایسه با جایگزینها
| پارامتر | این محصول | PCF8574N | PCF8574AN | PCF8574NG4 | PCF8574P,112 | PCF8574AP,112 |
|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | NXP Semiconductors | NXP Semiconductors |
| Package | 16-pin PDIP | 16-pin PDIP | 16-pin PDIP | 16-pin PDIP | 16-pin PDIP | 16-pin PDIP |
| Device Type | 8-bit I2C I/O expander | 8-bit I2C I/O expander | 8-bit I2C I/O expander | 8-bit I2C I/O expander | 8-bit I2C I/O expander | 8-bit I2C I/O expander |
| Number of I/O Lines | 8 lines | 8 lines | 8 lines | 8 lines | 8 lines | 8 lines |
| Maximum I2C Bus Frequency | 100 kHz | 100 kHz | 100 kHz | 100 kHz | 100 kHz | 100 kHz |
| Interface | I2C | I2C | I2C | I2C | I2C | I2C |
تفاوتهای کلیدی
- Directly matches the requested 8-bit and 100 kHz operating profile (در مقابلPCF8574P,112)
- Uses the same core interface and line count as the original Texas Instruments family (در مقابلPCF8574AN)
- Provides the expected eight-line expansion without requiring a larger parallel interface (در مقابلPCF8574AP,112)
یادداشتهای طراحی
Verify the 16-pin PDIP footprint, 7.62 mm lead pitch, and pin-one orientation against the manufacturer's package drawing before PCB release. The PCF8574ANG4 is a through-hole device, so account for lead diameter, drill size, pad clearance, and component-body height in the mechanical layout. Use a visible pin-one mark and avoid placing tall or heat-generating parts where they interfere with the expander body.
Keep the I2C clock and data traces short, route them away from switching nodes, and use pull-up resistors that satisfy the bus voltage and timing requirements at the maximum 100 kHz operating frequency. Check the complete network's effective capacitance, pull-up current, clock rise time, and available sink current. Where multiple expanders share the bus, review address selection and ensure the combined bus loading does not exceed the slowest participant.
Treat each of the eight I/O lines as a shared resource and avoid simultaneous external drive and output-mode operation. Firmware should establish the intended input or output direction before applying an external signal, and unused lines should be configured according to the manufacturer's recommended state. Because the device is identified as a 100 kHz I2C expander, do not assume it supports faster bus modes used by newer peripherals.
Follow the manufacturer's power and decoupling recommendations when connecting the device to a mixed digital system. Place local bypass capacitance close to the supply and ground pins, and account for switching current from attached I2C devices when estimating rail noise. If the eight lines drive external circuitry through transistors or relay drivers, calculate those loads separately because the expander's own supply demand alone does not represent the total board load.
اطلاعات انطباق
The component listing identifies PCF8574ANG4 as RoHS3 compliant. No verified information was available for REACH, AEC-Q100, lead-free status, halogen-free status, or conflict-minerals compliance.