PCM1718EG4 - 18-Bit Stereo Audio DAC | Texas Instruments
MPN: PCM1718EG4 ✗ Cuối đờiPCM1718EG4 Tóm tắt
An audio DAC converts digital audio samples into analog voltage signals that can drive downstream amplifiers, speakers, headphones, or line-level circuitry. Within the broader signal-chain hierarchy, the PCM1718EG4 is a stereo audio D/A converter, which is a specialized form of ADC/DAC semiconductor used in digital audio equipment. Its I2S interface connects with a digital audio processor or audio codec while the converter performs the final digital-to-analog conversion stage.
The primary specifications are 18-bit resolution, two audio channels, and a maximum sampling rate of 48 kHz. The 2.7 V to 5.5 V supply range allows operation from common low-voltage digital and analog rails. The 20-SSOP package provides a surface-mount implementation for compact consumer, communications, and industrial audio designs, while the specified -25°C to +85°C operating range supports moderate-temperature equipment.
The PCM1718EG4 is identified as a delta-sigma stereo DAC, pairing a serial digital input stage with dual analog output channels. The I2S interface is designed for integrated digital audio systems where clock and serial-data signals arrive from an audio processor. Dual-channel operation supports standard stereo playback paths without requiring two separate converter packages. Its 25 mA supply-current figure and 3.1 V maximum analog output voltage provide useful constraints for analog-output, power-budget, and downstream-signal-chain design.
Typical uses include stereo audio playback in consumer electronics, digital audio source equipment, multimedia systems, communications equipment, and embedded audio products. It is especially relevant where a 48 kHz sampling rate and 18-bit conversion are sufficient but a higher-resolution converter is unnecessary. The dual outputs can feed an audio amplifier or volume-control stage, while the I2S connection reduces the number of parallel digital signal lines required from the audio source.
Designers should treat the analog and digital supply rails as separate implementation concerns. Place the device-side bypass capacitors close to its supply pins and keep the analog output routing away from noisy digital clock and serial-data paths. The 20-SSOP footprint requires careful land-pattern reproduction, while the 3.1 V maximum analog output voltage must remain below downstream amplifier input limits.
This page organizes the PCM1718EG4 specifications, verified manufacturer documentation, sourcing information, functional application guidance, and the limited drop-in alternatives identified for the device. It also highlights design considerations that engineers can apply when evaluating this SoundPlus stereo DAC for an existing 20-SSOP audio subsystem.
Bộ thay thế dễ dàng lắp đặt cho PCM1718EG4 — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
PCM1718E/2KG4
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
PCM1718EG4 Tỷ lệ tối đa & tính chất điện
| Converter Type | Stereo audio digital-to-analog converter |
| Độ phân giải | 18 bit |
| Number of Channels | 2 channels |
| Maximum Sampling Rate | 48 kHz |
| Digital Interface | I2S |
| Supply Voltage Range | 2.7 V to 5.5 V |
| Điện áp cung cấp | 25 mA |
| Maximum Analog Output Voltage | 3.1 V |
| Khoảng nhiệt độ hoạt động | -25°C to +85°C |
| Hộp | 20-SSOP |
| Terminal Count | 20 terminals |
| Package Width | 0.209 m to 5.30 mm |
| Kiểu lắp đặt | Surface mount |
| Terminal Form | Gull wing |
| Converter Architecture | Delta-sigma |
| Product Family | SoundPlus stereo DAC |
Hướng dẫn cấu hình chân PCM1718EG4 0.209 m to 5.30 mm
Cấu hình chân cho PCM1718EG4 (0.209 m to 5.30 mm gói). Thành phần số hiệu này có chân đầu vào, đầu ra và nguồn cung cấp. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết cấu hình chân bù, bù trừ và chân kích hoạt. Hoàn hảo cho điều kiện tín hiệu và mạch khuếch đại.
Không có dữ liệu chân cụ thể sẵn có cho PCM1718EG4.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
PCM1718EG4 phù hợp cho 6 Áp dụngs: Stereo Consumer Audio Playback, Multimedia Audio Source Equipment, Communications Audio Terminal, Embedded Audio and IoT Devices, Digital Audio Headphone Front End, Industrial Audio Control Interface.
Stereo Consumer Audio Playback
The PCM1718EG4 fits stereo consumer audio playback because it combines 18-bit conversion, two output channels, and a 48 kHz maximum sampling rate. Place the converter after an audio processor that provides I2S data and clocks, then route its left and right analog outputs toward a volume-control and amplifier stage. Its 2.7 V to 5.5 V operating range supports common low-voltage equipment, while the 3.1 V maximum analog output voltage must remain compatible with downstream gain and clipping limits.
Được đề xuất
Multimedia Audio Source Equipment
A multimedia source can use the PCM1718EG4 as the final stereo DAC when its I2S interface matches the source processor and 18-bit, 48 kHz performance is adequate. The two-channel architecture avoids duplicating the converter for left and right audio paths. Its 25 mA supply current contributes to the converter rail budget, while the 20-SSOP package supports compact board layouts. Digital clock and data routing should remain separated from the analog output section to limit converted-signal contamination.
Được đề xuất
Communications Audio Terminal
The PCM1718EG4 is suitable for communications equipment requiring a compact stereo playback converter with a common digital-audio interface. An I2S source processor can feed the PCM1718EG4, whose left and right analog outputs can then drive a line-level or headphone amplification stage. The -25°C to +85°C operating range fits many indoor commercial environments, and the 2.7 V minimum supply voltage supports low-voltage embedded designs. Environmental requirements outside this range require a different converter.
Được đề xuất
Embedded Audio and IoT Devices
Compact embedded and IoT products can use the PCM1718EG4 when the audio subsystem requires an I2S-compatible stereo DAC without a higher-resolution or higher-rate converter. Its 20-SSOP surface-mount package conserves board area, and its 2.7 V to 5.5 V range accommodates common digital supply systems. The design must account for the 25 mA supply demand, provide local bypass capacitance, and keep analog outputs short and well separated from switching regulators and fast digital clocks.
Được đề xuất
Digital Audio Headphone Front End
The PCM1718EG4 can form the converter stage of a digital headphone front end when 18-bit resolution and 48 kHz sampling meet the product requirements. The I2S input accepts digital audio from the playback engine, and the dual analog outputs feed the headphone amplifier. Because the maximum analog output voltage is 3.1 V, gain and headroom must be calculated before the downstream stage is selected. Close placement of supply bypass components also helps maintain a stable converter reference during playback transitions.
Được đề xuất
Industrial Audio Control Interface
The PCM1718EG4 can serve as the audio conversion element in industrial equipment that accepts digital audio and requires two analog output channels. Its operating range of -25°C to +85°C supports many industrial indoor environments, while the compact 20-SSOP package fits space-constrained control panels or embedded subsystems. Designers should verify EMC susceptibility, grounding, and analog-output headroom under the full temperature range. The I2S timing and supply requirements must also satisfy the system's digital source during worst-case processing load.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho PCM1718EG4 — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | PCM1718E/2KG4 |
|---|---|---|
| Brand | Texas Instruments | Texas Instruments |
| Package | 20-SSOP | 20-SSOP |
| Resolution | 18 bit | 18 bit |
| Number of Channels | 2 channels | 2 channels |
| Maximum Sampling Rate | 48 kHz | 48 kHz |
| Digital Interface | I2S | I2S |
| Supply Voltage Range | 2.7 V to 5.5 V | 2.7 V to 5.5 V |
Bảo phân biệt quan trọng
- Directly identified same-package replacement path (vsPCM1718E/2KG4)
- Stereo conversion in one package (vsPCM1718E/2KG4)
- Direct digital-audio interface (vsPCM1718E/2KG4)
Ghi chú thiết kế
Reproduce the 20-SSOP land pattern directly from the Texas Instruments package drawing and route both analog outputs away from the I2S clock and data traces. Place the device-side supply bypass capacitors close to the supply and ground pins to minimize loop area. Keep the two output traces short and symmetrical when they feed a stereo amplifier or volume-control network.
Budget the PCM1718EG4's 25 mA supply current when designing the analog rail and bypass network. The supported operating range is 2.7 V to 5.5 V, but the usable output headroom must also be checked against the 3.1 V maximum analog output voltage. A regulator selected only for nominal voltage compatibility may still be unsuitable if its transient response, noise, or allowable headroom is inadequate.
Confirm the source processor's I2S clock polarity, data timing, and sample-rate relationship against the PCM1718 datasheet before releasing the PCB. Route clock and serial data as controlled-impedance digital signals over a continuous reference plane, and avoid sharing long paths with analog outputs. Grounding and return-current decisions should minimize coupling between the digital input section and the two analog output channels.
Thông tin tuân thủ
The manufacturer product documentation and distributor listings do not establish the requested compliance statuses for PCM1718EG4. The part is identified as not intended for new designs. A public comparison page mentions RoHS and REACH, but it does not provide explicit status values for this exact orderable code.