PCM1771RGA - 24-Bit Stereo Audio DAC with Headphone Amp | TI
MPN: PCM1771RGA ✓ Hoạt độngPCM1771RGA Tóm tắt
An audio DAC is a signal-conversion integrated circuit that transforms digital audio samples into an analog voltage waveform suitable for amplification, loudspeaker drive, or headphone output. PCM1771 belongs to the DAC hierarchy within audio converters, ADC/DAC integrated circuits, and broader semiconductor components. Its integrated headphone circuitry reduces the number of external analog-output stages needed in portable and multimedia equipment while retaining a compact surface-mount footprint.
Key features include 24-bit resolution, a maximum sampling rate of 50 kHz, 98 dB SNR, stereo DAC channels, an I2S-compatible digital interface, and a low-power CMOS implementation. The enhanced multilevel converter architecture uses noise shaping and multilevel amplitude quantization to improve dynamic performance. A hardware-control headphone-amplifier option supports systems requiring direct control of the headphone-output operating state.
The PCM1771 combines its digital input section, stereo conversion core, analog output circuitry, and headphone amplifier within one package. Its I2S interface allows connection to a digital-audio source such as a sound-card controller, portable-media processor, or audio interface. Noise shaping redistributes quantization noise away from the most perceptually important audio band, while 24-bit quantization supports a high-resolution representation of each sample. The 4.2 mm by 4.2 mm VQFN-20 package supports compact PCB layouts but requires careful exposed-pad thermal and layout management.
Typical applications include headphone-equipped portable players, digital audio accessories, multimedia speakers, USB or portable-audio interfaces, consumer electronics, and embedded audio systems. The integrated headphone stage is particularly useful when the design requires analog headphone output without a separate headphone-amplifier IC. Systems requiring simultaneous microphone capture and headphone playback should also evaluate the clocking, interface format, and analog routing of the complete design rather than assuming every codec requirement is covered.
The primary design considerations are correct I2S data and clock connections, compliant digital supply sequencing, analog-output filtering, and the PCB treatment of the VQFN exposed pad. Keep digital return currents away from the analog output and headphone-driver paths, place decoupling capacitors near their associated supply pins, and use a ground plane that does not split the return network beneath the converter. Confirm the selected output mode and filter components against the manufacturer datasheet before releasing a PCB layout.
This product data consolidates the exact PCM1771RGA package, interface, resolution, sampling, SNR, temperature, and conversion-architecture details with practical application guidance, sourcing instructions, and same-package family comparisons. It is designed to help engineers determine whether the converter suits a new audio design and how to evaluate qualified alternatives before committing a board layout.
Bộ thay thế dễ dàng lắp đặt cho PCM1771RGA — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với PCM1771RGA (cùng hình factor và footprint) — khác nhau ở Number of DAC Channels, Package, Product Type.
PCM1770RGA
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
PCM1773RGAR
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
PCM1771RGA Tỷ lệ tối đa & tính chất điện
| Product Type | Stereo audio digital-to-analog converter with headphone amplifier |
| Converter Resolution | 24 bit |
| Maximum Sampling Rate | 50 kHz |
| Signal-to-Noise Ratio | 98 dB |
| Digital Audio Interface | I2S |
| Number of DAC Channels | 2 stereo channels |
| Headphone Amplifier | Integrated with hardware control |
| Conversion Architecture | Enhanced multilevel architecture with noise shaping and multilevel amplitude quantization |
| Process Technology | CMOS |
| Hộp | 20-pin VQFN (RGA) |
| Package Dimensions | 4.2 mm x 4.2 mm |
| Số lượng chân | 20 pins |
| Kiểu lắp đặt | Surface mount |
| Nhiệt độ hoạt động | 0 C to 70 C |
| Power Class | Low-power operation |
Hướng dẫn cấu hình chân PCM1771RGA 4.2 mm x 4.2 mm
Cấu hình chân cho PCM1771RGA (4.2 mm x 4.2 mm gói). Thành phần số hiệu này có chân đầu vào, đầu ra và nguồn cung cấp. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết cấu hình chân bù, bù trừ và chân kích hoạt. Hoàn hảo cho điều kiện tín hiệu và mạch khuếch đại.
Không có dữ liệu chân cụ thể sẵn có cho PCM1771RGA.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
PCM1771RGA phù hợp cho 6 Áp dụngs: Portable Headphone Audio Player, Digital Audio Interface, Multimedia Speaker System, USB Audio Accessory, Consumer Audio Embedded System, Broadcast and Studio Monitoring.
Portable Headphone Audio Player
The PCM1771RGA fits portable headphone equipment that accepts digital audio through I2S and needs a compact stereo analog-output stage. Its 24-bit conversion resolution, 50 kHz maximum sampling rate, and 98 dB SNR provide the core performance parameters for a low-noise playback path. The integrated headphone amplifier reduces the component count compared with a discrete DAC and separate headphone-driver design, while the 4.2 mm by 4.2 mm VQFN-20 package preserves board area. The 0 C to 70 C rating suits controlled consumer environments, but battery-operated products must verify supply range and total power consumption in the manufacturer data sheet.
Được đề xuất
Digital Audio Interface
PCM1771RGA is appropriate for a compact digital-to-analog interface that receives I2S audio from a USB controller, application processor, or digital-audio transceiver. The 24-bit stereo converter and 98 dB SNR provide a clear conversion specification, while the 50 kHz maximum sampling rate supports conventional audio-rate streams. Integrating headphone circuitry also enables a monitor-output implementation with fewer board-level blocks. Designers should treat the converter as a controlled analog signal path: isolate clocks and digital return currents from the output section, and validate output filtering, channel mapping, and headphone-load behavior with the application circuit.
Được đề xuất
Multimedia Speaker System
The PCM1771RGA can provide the stereo digital-to-analog conversion stage for a compact multimedia speaker or powered-audio system. Its 24-bit resolution and 98 dB SNR establish the conversion performance, while I2S allows direct connection to a digital-audio source without a parallel-data interface. The low-power CMOS implementation is useful where the speaker controller must operate within a limited power budget. For best results, place the analog outputs away from switching regulators and high-current amplifier traces, follow the specified output-filter network, and confirm that the headphone-amplifier section is configured appropriately for the intended output architecture.
Được đề xuất
USB Audio Accessory
PCM1771RGA suits a USB audio accessory that converts a digital playback stream into stereo analog sound for headphones or line-level circuitry. The I2S interface is well suited to common audio bridges, the 24-bit converter supports high-resolution playback, and the 98 dB SNR specification is appropriate for reducing digital-to-analog noise. Its small VQFN-20 package leaves room for USB-interface and power-supply components on a portable board. Layout should maintain short analog paths from the converter to the output stage, provide continuous ground references, and separate switching-converter current paths from the 24-bit audio conversion section.
Được đề xuất
Consumer Audio Embedded System
The PCM1771RGA is suitable for embedded consumer products that process audio digitally and require a compact stereo output with integrated headphone drive. The combination of a 24-bit converter, 50 kHz sampling capability, I2S connectivity, and integrated headphone circuitry makes it appropriate for appliances, personal-audio products, and compact control panels. The 0 C to 70 C specification fits room-temperature consumer environments, but enclosure temperature rise must remain within that range. Firmware should configure the digital stream and control pins to match the device interface, and the PCB should provide clean analog grounding and the manufacturer-specified output filtering.
Được đề xuất
Broadcast and Studio Monitoring
PCM1771RGA can support a compact monitoring path when the system uses 24-bit digital audio and requires a local headphone output from the converter. Its 98 dB SNR rating and 50 kHz maximum sampling rate provide useful baseline parameters for consumer-grade and space-constrained monitoring equipment. The integrated headphone amplifier is valuable for personal monitoring, although professional applications must separately verify noise, distortion, frequency response, channel separation, and output-drive requirements. Keep the digital audio source and converter clocking deterministic, use short analog routing, and validate the external reconstruction-filter network against the manufacturer's recommended circuit.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho PCM1771RGA — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | PCM1770RGA | PCM1773RGAR |
|---|---|---|---|
| Package | VQFN-20 (RGA), 4.2 mm x 4.2 mm | VQFN-20 (RGA) | VQFN-20 (RGA) |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
Bảo phân biệt quan trọng
- Documented hardware-controlled headphone-amplifier arrangement (vsPCM1770RGA)
- Manufacturer-specified 98 dB signal-to-noise ratio (vsPCM1770RGA)
- Common 20-pin RGA footprint with explicit 24-bit and 50 kHz positioning (vsPCM1773RGAR)
Ghi chú thiết kế
Treat the PCM1771RGA as a mixed-signal device even though its digital interface is relatively simple. Route I2S data and clock signals away from the analog and headphone-output paths, provide a continuous ground reference, and place required bypass components at the pins specified by the manufacturer reference circuit. Confirm the exposed-pad net in the package drawing before connecting it to ground or a supply plane.
Use the manufacturer's clocking and digital-interface requirements to establish a stable sample clock and correct I2S word alignment. Grounding, shielding, and power-distribution design are especially important when the converter is mounted near a switching supply, radio-frequency section, or high-speed digital processor. Confirm output filtering and channel mapping with the reference design rather than assuming that identical I2S labels guarantee identical polarity or timing.
Do not treat a shared 20-pin RGA package as proof that any family member is automatically interchangeable. Before replacing PCM1771RGA with PCM1770RGA or PCM1773RGAR, compare power pins, ground connections, clock requirements, control polarity, headphone-output behavior, analog filters, and digital interface settings. Also check the exposed-pad electrical assignment and land pattern rather than relying only on the number of package leads.
Thông tin tuân thủ
The exact product information identifies a 0 C to 70 C commercial-temperature PCM1771RGA but does not establish RoHS, REACH, lead-free, halogen-free, conflict-minerals, or automotive qualification status for this orderable device.