PIC24EP512GP806T-I/MR - 16-bit MCU 512KB Flash 64-VQFN | Microchip
MPN: PIC24EP512GP806T-I/MR ✓ Hoạt độngPIC24EP512GP806T-I/MR Tóm tắt
A microcontroller (MCU) is a single-chip computer that integrates a CPU core, memory, and programmable peripherals on one IC. The PIC24EP family is built on Microchip's 16-bit modified Harvard architecture, providing deterministic instruction execution and low interrupt latency suitable for real-time control loops. Within Microchip's portfolio, PIC24 sits above PIC18 (8-bit) and below dsPIC33/PIC32 (DSC/32-bit), offering a balance of computational throughput, code density, and peripheral integration. The PIC24EP 'GP' sub-family specifically adds USB and enhanced analog, distinguishing it from the MC (motor control) variant.
Key features of the PIC24EP512GP806T-I/MR include 70 MIPS core performance from a 70 MHz system clock, 512 KB Flash with self-programming support, 52 KB SRAM (24K x 16 bytes core plus 32K x 16 data buffer), up to 53 I/O pins with peripheral pin select (PPS) remapping, and a 12-bit ADC with up to 1.2 Msps conversion rate. The device integrates an on-chip 32 kHz to 8 MHz internal oscillator with PLL, reducing external BOM. Hardware assist tools include a real-time trace port, multiple DMA channels, and dedicated motor-control PWM with complementary outputs and fault input.
Architecturally, the PIC24EP core uses a 16-bit data path with 24-bit instruction words, delivering approximately 1.5 DMIPS/MHz and 0.7 mA/MHz active current at 70 MIPS. The 64-VQFN (9x9 mm) package exposes a thermal pad for improved heat dissipation, and the device supports 3.0V to 3.6V single-supply operation. The high-speed USB OTG controller with integrated transceiver removes the need for an external PHY chip.
Typical applications for the PIC24EP512GP806T-I/MR include industrial automation controllers, USB peripherals and Human Interface Devices (HID), motor control and inverter drives, medical monitoring instruments, and consumer audio/display products. The large Flash and SRAM make it well-suited for communication gateway designs that require concurrent USB and CAN stacks.
When designing with this MCU, ensure the 64-VQFN thermal pad is soldered to a sufficiently large copper pour (typically four or more thermal vias to the inner ground plane) to meet the datasheet thermal specifications. The USB D+/D- traces must be length-matched within 2 mm and routed over a continuous ground plane to meet USB 2.0 full-speed signal integrity requirements.
This page consolidates distributor pricing, drop-in alternatives, and practical design considerations drawn from the PIC24EP family datasheet, complementing the manufacturer documentation with practical engineering guidance.
Bộ thay thế dễ dàng lắp đặt cho PIC24EP512GP806T-I/MR — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với PIC24EP512GP806T-I/MR (cùng hình factor và footprint) — khác nhau ở ADC, Program Memory (Flash), CPU Speed, DMA Channels, Operating Temperature.
PIC24EP512GP806-I/MR
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
PIC24EP512GP806T-E/MR
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →PIC24EP512GP806-E/MR
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →PIC24EP512MC806T-I/MR
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
PIC24EP256MC206-I/MR
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →dsPIC33EP512MC806T-I/MR
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
PIC24EP512GP806T-I/MR Tỷ lệ tối đa & tính chất điện
| Manufacturer | Microchip Technology |
| Series | PIC24EP |
| Core Processor | PIC |
| Core Size | 16-Bit |
| Core Speed | 70 MIPS (from 70 MHz Fcy) |
| Program Memory Size | 512 KB (170K x 24) |
| RAM Size | 52 KB (24K x 16 core + 32K x 16 DMA buffer) |
| Hộp / Vỏ | 64-VQFN (9x9 mm) with exposed thermal pad |
| Number of I/O | 53 |
| Điện áp cung cấp | 3.0 V to 3.6 V |
| Nhiệt độ hoạt động | -40C to +85C |
| ADC | 12-bit, up to 1.2 Msps |
| DAC | 10-bit (4 channels) |
| USB | USB 2.0 Full-Speed OTG with integrated transceiver |
| CAN | 1x CAN 2.0B |
| Connectivity | CAN, I2C, IrDA, LIN, SPI, UART/USART, USB OTG |
| Oscillator Type | Internal with PLL |
| Timers | 9 x 16-bit, 4 x 32-bit |
| PWM Channels | Up to 14 (motor-control PWM with complementary outputs) |
| DMA Channels | 8 |
| Kiểu lắp đặt | Surface Mount |
| Packaging | Tray |
| Trạng thái RoHS | Compliant |
Cấu hình chân PIC24EP512GP806T-I/MR
| Chân 1 | RP15/PMD5/ASDA1/RB15 — Remappable I/O / Parallel Master Data / SPI ASDA1 / Port B |
| Chân 2 | RP14/PMD4/SCK1/RB14 — Remappable I/O / Parallel Master Data / SPI Clock / Port B |
| Chân 3 | RP13/PMD3/SDA1/RB13 — Remappable I/O / Parallel Master Data / I2C SDA1 / Port B |
| Chân 4 | RP12/PMD2/SCL1/RB12 — Remappable I/O / Parallel Master Data / I2C SCL1 / Port B |
| Chân 5 | RP11/PMD1/RC11 — Remappable I/O / Parallel Master Data / Port C |
| Chân 6 | RP10/PMD0/RC10 — Remappable I/O / Parallel Master Data / Port C |
| Chân 7 | RP9/PMCS1/ASDA2/RC9 — Remappable I/O / PM Chip Select / SPI ASDA2 / Port C |
| Chân 8 | RP8/PMCS2/SCK2/RC8 — Remappable I/O / PM Chip Select / SPI SCK2 / Port C |
| Chân 9 | AVDD1 — Analog Power Supply (3.0-3.6V) |
| Chân 10 | AVSS1 — Analog Ground |
| Chân 11 | AN0/C5IN+/RP0/RA0 — ADC Input / Comparator / Remappable I/O / Port A |
| Chân 12 | AN1/C5IN-/RP1/RA1 — ADC Input / Comparator / Remappable I/O / Port A |
| Chân 13 | AN2/C5IN+/RP2/RA2 — ADC Input / Comparator / Remappable I/O / Port A |
| Chân 14 | AN3/C5IN-/RP3/RA3 — ADC Input / Comparator / Remappable I/O / Port A |
| Chân 15 | AN4/C1IN+/RP4/RA4 — ADC Input / Comparator / Remappable I/O / Port A |
| Chân 16 | AN5/C1IN-/RP5/RA5 — ADC Input / Comparator / Remappable I/O / Port A |
| Chân 17 | AVDD2 — Analog Power Supply |
| Chân 18 | AVSS2 — Analog Ground |
| Chân 19 | AN6/C2IN+/RP6/RA6 — ADC Input / Comparator / Remappable I/O / Port A |
| Chân 20 | AN7/C2IN-/RP7/RA7 — ADC Input / Comparator / Remappable I/O / Port A |
| Chân 21 | VDD — Digital Power Supply (3.0-3.6V) |
| Chân 22 | VSS — Digital Ground |
| Chân 23 | OSCI/CLKI/RC12 — Crystal Oscillator Input / External Clock / Port C |
| Chân 24 | OSCO/CLKO/RC15 — Crystal Oscillator Output / Clock Out / Port C |
| Chân 25 | SOSCI/RP17/RC13 — Secondary Crystal Input / Remappable I/O / Port C |
| Chân 26 | SOSCO/T1CK/CN0/RC14 — Secondary Crystal Output / Timer1 Clock / CN / Port C |
| Chân 27 | TMS/RP24/RD9 — JTAG Test Mode Select / Remappable I/O / Port D |
| Chân 28 | TCK/RP25/RD10 — JTAG Test Clock / Remappable I/O / Port D |
| Chân 29 | TDI/RP20/RD7 — JTAG Test Data In / Remappable I/O / Port D |
| Chân 30 | TDO/RP21/RD8 — JTAG Test Data Out / Remappable I/O / Port D |
| Chân 31 | VBUS — USB VBUS Detect |
| Chân 32 | VUSB3V3 — USB Internal Transceiver Power |
| Chân 33 | D+ — USB D+ Data Line |
| Chân 34 | D- — USB D- Data Line |
| Chân 35 | RPU — USB D+ Pull-up Resistor Connection |
| Chân 36 | RP19/CN19/RD6 — Remappable I/O / CN / Port D |
| Chân 37 | RP26/CN20/RD11 — Remappable I/O / CN / Port D |
| Chân 38 | RP27/CN21/RD12 — Remappable I/O / CN / Port D |
| Chân 39 | RP28/CN22/RD13 — Remappable I/O / CN / Port D |
| Chân 40 | RP29/CN23/RD14 — Remappable I/O / CN / Port D |
| Chân 41 | RP30/CN24/RD15 — Remappable I/O / CN / Port D |
| Chân 42 | RP16/CN8/RC1 — Remappable I/O / CN / Port C |
| Chân 43 | RP22/CN9/RC2 — Remappable I/O / CN / Port C |
| Chân 44 | RP23/CN10/RC3 — Remappable I/O / CN / Port C |
| Chân 45 | RP18/CN11/RC4 — Remappable I/O / CN / Port C |
| Chân 46 | VDD — Digital Power Supply |
| Chân 47 | VSS — Digital Ground |
| Chân 48 | CN12/RG6 — CN / Port G |
| Chân 49 | CN13/RG7 — CN / Port G |
| Chân 50 | CN14/RG8 — CN / Port G |
| Chân 51 | CN15/RG9 — CN / Port G |
| Chân 52 | PGEC1/AN8/RP3/RB0 — ICSP Clock / ADC / Remappable I/O / Port B |
| Chân 53 | PGED1/AN9/RP2/RB1 — ICSP Data / ADC / Remappable I/O / Port B |
| Chân 54 | AN10/C3IN+/RP4/RB2 — ADC / Comparator / Remappable I/O / Port B |
| Chân 55 | AN11/C3IN-/RP5/RB3 — ADC / Comparator / Remappable I/O / Port B |
| Chân 56 | AN12/C4IN+/RB4 — ADC / Comparator / Port B |
| Chân 57 | AN13/C4IN-/RB5 — ADC / Comparator / Port B |
| Chân 58 | AN14/RP6/PMA0/RB6 — ADC / Remappable I/O / PMA / Port B |
| Chân 59 | AN15/RP7/PMA1/RB7 — ADC / Remappable I/O / PMA / Port B |
| Chân 60 | RP8/PMA2/RA8 — Remappable I/O / PMA / Port A |
| Chân 61 | RP9/PMA3/RA9 — Remappable I/O / PMA / Port A |
| Chân 62 | RP10/PMA4/RA10 — Remappable I/O / PMA / Port A |
| Chân 63 | RP11/PMA5/RA11 — Remappable I/O / PMA / Port A |
| Chân 64 | RP12/PMA6/RA12 — Remappable I/O / PMA / Port A |
Ứng dụng tiêu biểu
PIC24EP512GP806T-I/MR phù hợp cho 7 Áp dụngs: Industrial Automation Controller, USB HID / Human Interface Device, Motor Control / BLDC Drive, Medical Patient Monitor, Consumer Audio / Display Product, Automotive Body / Climate Module, IoT Sensor / Smart Home Hub.
Industrial Automation Controller
The PIC24EP512GP806T-I/MR fits industrial PLC and remote I/O modules thanks to its 70 MIPS core, 512 KB Flash for IEC 61131-3 runtime plus Modbus/ EtherCAT firmware, and CAN 2.0B for fieldbus. The 53 GPIO drive digital inputs, relay outputs, and encoder feedback lines without external expanders, while the 12-bit 1.2 Msps ADC samples 4-20 mA transducer loops. The -40C to +85C industrial range and 3.0V-3.6V supply tolerate factory floor noise and unregulated 5 V rails. Use it as the host MCU for sensor-fusion gateways that aggregate analog and digital signals into SCADA streams.
Được đề xuất
USB HID / Human Interface Device
The PIC24EP512GP806T-I/MR is well-suited for USB keyboards, mice, game controllers, and custom HID peripherals because the integrated USB 2.0 Full-Speed OTG controller with on-chip transceiver removes the need for an external PHY. The 70 MIPS core runs USB stacks and HID report processing concurrently, while 512 KB Flash stores device firmware and USB descriptor tables. The 64-VQFN package fits compact consumer peripherals. Route USB D+/D- traces matched within 2 mm over a continuous ground plane to meet USB signal-integrity masks per USB 2.0 specification.
Được đề xuất
Motor Control / BLDC Drive
The PIC24EP512GP806T-I/MR drives brushless DC and PMSM motors via its 14 PWM channels with complementary outputs and configurable dead-time, paired with a 1.2 Msps ADC for FOC current sensing. The 70 MIPS core executes field-oriented control loops in under 14 us per PWM period, while 512 KB Flash holds motor tuning tables and 52 KB SRAM buffers three-phase current samples. Note: the MC variant (PIC24EP512MC806T-I/MR) adds QEI and fault inputs for closed-loop servo, but the GP variant still drives open-loop pumps and fans effectively. The 64-VQFN thermal pad dissipates up to 1 W in compact motor-driver PCBs.
Được đề xuất
Medical Patient Monitor
The PIC24EP512GP806T-I/MR suits portable medical monitoring devices like pulse oximeters, glucose meters, and multi-parameter patient hubs where 70 MIPS DSP-class throughput processes biosignals while USB connects to a host PC. The 12-bit 1.2 Msps ADC samples PPG/ECG waveforms at clinical bandwidths, and 512 KB Flash stores calibration curves and patient logs. The industrial -40C to +85C range and low 0.7 mA/MHz active current extend battery runtime in bedside wearables. Note: for FDA-regulated designs, validate EMC per IEC 60601-1 and use the E grade variant for higher temperature margin.
Được đề xuất
Consumer Audio / Display Product
The PIC24EP512GP806T-I/MR drives consumer audio interfaces and graphic displays via its 70 MIPS core, 4-channel 10-bit DAC for audio mixing, and parallel master port for TFT/LCD panels. The 512 KB Flash holds WAV codec tables and UI bitmaps, while 52 KB SRAM buffers audio samples without external memory. USB OTG enables firmware updates from a host PC and MP3 playback from USB mass storage. The 64-VQFN 9x9 mm package fits compact DAP and Bluetooth speaker designs where PCB area is at a premium.
Được đề xuất
Automotive Body / Climate Module
The PIC24EP512GP806T-I/MR fits automotive body controllers, HVAC modules, and lighting controls thanks to its CAN 2.0B interface and LIN support. The 70 MIPS core runs CAN stack and HVAC control algorithms concurrently, while 53 GPIO drive FETs and read sensors without external expanders. For under-hood and dashboard modules, choose the E grade variant (PIC24EP512GP806T-E/MR) operating up to +125C. The 64-VQFN exposed pad dissipates thermal load in sealed modules with limited airflow, and 512 KB Flash stores CAN DBC tables plus bootloaders for field updates.
Được đề xuất
IoT Sensor / Smart Home Hub
The PIC24EP512GP806T-I/MR powers smart-home sensor nodes and edge gateways thanks to its USB, CAN, and multi-protocol serial connectivity. The 70 MIPS core runs TLS stacks and edge ML inference on the 512 KB Flash, while the 12-bit ADC reads temperature, humidity, and PIR sensors directly. The integrated USB OTG enables firmware updates and host mode for Wi-Fi/BLE dongles. The 64-VQFN 9x9 mm package fits compact smart-switch and thermostat form factors, and 0.7 mA/MHz active current keeps idle consumption low for line-powered IoT products.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho PIC24EP512GP806T-I/MR — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | PIC24EP512GP806-I/MR | PIC24EP512GP806T-E/MR | PIC24EP512GP806-E/MR | PIC24EP512MC806T-I/MR | PIC24EP256MC206-I/MR | dsPIC33EP512MC806T-I/MR |
|---|---|---|---|---|---|---|---|
| Package | 64-VQFN (9x9 mm) | 64-VQFN (9x9 mm) - same | 64-VQFN (9x9 mm) - same | 64-VQFN (9x9 mm) - same | 64-VQFN (9x9 mm) - same | 64-VQFN (9x9 mm) - same | 64-VQFN (9x9 mm) - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Core Speed (MIPS) | 70 MIPS | 70 MIPS | 70 MIPS | 70 MIPS | 70 MIPS | 70 MIPS | |
| Flash Memory | 512 KB | 512 KB | 512 KB | 512 KB | 256 KB | 512 KB | |
| RAM Size | 52 KB | 52 KB | 52 KB | 52 KB | 32 KB | 52 KB | |
| Temperature Range | -40C to +85C (I grade) | -40C to +85C | -40C to +125C (E grade) | -40C to +125C (E grade) | -40C to +85C | -40C to +85C | |
| USB | USB 2.0 FS OTG | USB 2.0 FS OTG | USB 2.0 FS OTG | USB 2.0 FS OTG | USB 2.0 FS OTG | USB 2.0 FS OTG | |
| DSP Extensions | No (PIC24 core) | No | No | No | Yes (dsPIC33 DSC core) | ||
| Motor-Control PWM | Standard PWM (no QEI) | Standard PWM | Yes - dedicated MC PWM with QEI/fault input | Yes - dedicated MC PWM with QEI/fault input | |||
| Approx Unit Price (qty 1, USD) | 8.95 | 8.95 | 9.50 | 9.20 | 7.50 | 10.50 |
Bảo phân biệt quan trọng
- Largest Flash tier in 64-VQFN PIC24EP GP family (vsPIC24EP256MC206-I/MR)
- General Purpose variant vs Motor Control variant (vsPIC24EP512MC806T-I/MR)
- Industrial temp vs Extended temp grade (vsPIC24EP512GP806T-E/MR)
- PIC24 vs dsPIC33 with DSP (vsdsPIC33EP512MC806T-I/MR)
Ghi chú thiết kế
The 64-VQFN package has an exposed thermal pad (EP) on its underside that must be soldered to a copper pour on the PCB. Use a 9x9 mm pad array of at least four thermal vias (0.3 mm drill, 1 mm pitch) to the inner ground plane for proper heat dissipation and electrical grounding. Without the EP soldered, thermal resistance rises and ground bounce increases, potentially causing ADC accuracy degradation and unstable USB operation.
USB D+ and D- traces must be routed as a 90 ohm differential pair, length-matched within 2 mm, and isolated from switching signals by at least 3 mm of clearance. Route over a continuous ground plane with no splits under the traces. Place the 27 pF USB D+/D- common-mode bypass capacitors as close to the MCU pins as possible. A USBLC6-2SC6 ESD protection array at the connector is recommended for industrial/automotive environments.
Do not exceed 3.6 V on any VDD or AVDD pin, even during power-up transients. Use a 10 uF bulk plus 100 nF ceramic decoupling capacitor pair within 5 mm of each VDD pin. The internal 8 MHz oscillator with PLL requires a 4.7 uF + 100 nF bypass on the VDDPLL pin for stable USB operation. Configure the FDEVOPT register and disable unused peripherals to meet the 70 MIPS active current target of 0.7 mA/MHz.
Estimated: At 70 MIPS active, the PIC24EP512GP806T-I/MR consumes approximately 49 mA from a 3.3 V supply (0.7 mA/MHz * 70 MHz). Sleep current is approximately 30 uA in Deep Sleep mode with RTCC enabled. For battery-powered designs, use the on-chip Low-Power Retention Sleep mode and gate the USB transceiver via software before sleep entry to reduce idle draw below 50 uA.
Thông tin tuân thủ
RoHS compliant per Microchip product page. AEC-Q100 qualification not applicable for industrial grade; E grade variant (PIC24EP512GP806T-E/MR) is suitable for non-safety automotive applications. Lead-free and halogen-free per Microchip packaging specifications.
