SI3050-E-GT - 3.3V Global Voice DAA | Silicon Labs
MPN: SI3050-E-GT ✗ Cuối đờiSI3050-E-GT Tóm tắt
A Voice DAA is the analog interface between a telephone line and a digital voice processor. In the signal path, it supervises the line, detects seizure and off-hook conditions, handles hook-state transitions, and exposes the voice path to a digital PCM interface. The SI3050 belongs to the broader telecom-interface IC and Direct Access Arrangement hierarchy, placing it between a physical telephone network and a voice codec, DSP, or system controller.
The SI3050 is fully software programmable and supports country-specific PTT behavior. The manufacturer identifies compliance with FCC, TBR21, JATE, and other regional PTT requirements. Its global-programmability architecture is intended to accommodate differences in line-current detection, impedance, ring voltage, off-hook timing, and hook-state reporting without redesigning the analog telephone interface.
Silicon Labs patented isolation-capacitor technology is a major technical feature of the Si3050/Si3011/Si3018/Si3019 family. This approach removes the need for conventional isolation transformers, relays, or opto-isolators in the supported line interface, reducing board area and simplifying assembly while retaining the required separation between the telephone line and host circuitry. The companion Si3011, Si3018, or Si3019 device provides the line-side functions, while the SI3050 connects that interface to the digital side.
Typical uses include voice gateways, embedded voice servers, fax and multifunction-printer interfaces, VoIP terminal equipment, digital PBX peripheral modules, and caller-ID or message-waiting systems. The 3.3 V host supply and PCM-oriented digital interface are particularly suitable for modern processor-based communication equipment. Designers should still review the family data sheet for clocking, line-side companion selection, register programming, country configuration, and PCB layout requirements.
The SI3050-E-GT is specified in a 20-pin TSSOP package and is identified as revision E. Its lead-free construction is explicitly listed for the exact ordering code. Because legacy Voice DAA availability is limited, engineers should verify lifecycle status, supported software configuration, and the required companion line-side IC before committing a new design. This page combines exact ordering information, programmable Voice DAA characteristics, application guidance, and practical design considerations for engineers evaluating the SI3050-E-GT.
Bộ thay thế dễ dàng lắp đặt cho SI3050-E-GT — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
SI3050-E1-GT
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
SI3050-E-FT
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →SI3050-E1-FT
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
SI3050-E1-FTR
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
SI3050-E-FTR
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
SI3050-E-GT Thông số kỹ thuật
| Product Type | Programmable Voice Direct Access Arrangement (DAA) |
| Điện áp cung cấp | 3.3 V |
| Hộp | 20-pin TSSOP |
| Kiểu lắp đặt | Surface mount |
| Device Revision | Revision E |
| Digital Interface | Standard telephony PCM interface |
| Line Interface | System-side FXO analog interface |
| Programmability | Software programmable |
| Isolation Method | Patented isolation capacitor technology |
| Required Line-Side Companion | Si3011, Si3018, or Si3019 |
| FCC Compliance | FCC Parts 15 and 68 |
| European Emissions Compliance | EN55022 |
| European Immunity Compliance | EN55024 |
| PTT Standards | FCC, TBR21, JATE, and country-specific requirements |
| Lead-Free Construction | Lead-free |
Hướng dẫn cấu hình chân SI3050-E-GT 20-pin tssop
Cấu hình chân cho SI3050-E-GT (20-pin tssop gói). Số thứ tự chân, chức năng và sơ đồ kết nối được xác định trong tài liệu thông số kỹ thuật của nhà sản xuất. Tham khảo nó để biết footprint và hướng dẫn hàn chính xác.
Không có dữ liệu chân cụ thể sẵn có cho SI3050-E-GT.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
SI3050-E-GT phù hợp cho 6 Áp dụngs: Voice-over-IP Terminals, Voice Gateway Equipment, Multifunction Printer Fax Modules, Digital PBX Peripheral Cards, Analog Caller-ID Systems, Industrial Telephone Monitoring.
Voice-over-IP Terminals
The SI3050-E-GT fits a Voice-over-IP terminal that must connect an analog telephone line to a digital voice subsystem. Its 3.3 V host-side operation and standard telephony PCM interface allow a codec or DSP to handle digitized voice while the SI3050 manages the system side of the programmable FXO interface. Software-configurable PTT behavior is valuable when one product family must support different international line requirements. The Si3050 and Si3011/18/19 family data sheet identifies FCC, TBR21, JATE, and country-specific support, reducing the need for separate analog interface boards. Designers must select the appropriate line-side companion and implement the recommended isolation-capacitor layout.
Được đề xuất
Voice Gateway Equipment
A voice gateway can place the SI3050-E-GT between an FXO line and a PCM-based processor interface. The IC provides the system-side portion of a programmable global Voice DAA solution and supports standardized hook-state and line supervision behavior. This is useful when a gateway must meet more than one regional PTT specification without redesigning the analog front end. According to the Si3050 family data sheet, the architecture supports FCC Parts 15 and 68, EN55022, EN55024, TBR21, JATE, and other country-specific requirements. The primary implementation constraint is matching the correct Si3011, Si3018, or Si3019 line-side companion and validating the exact regional configuration before production.
Được đề xuất
Multifunction Printer Fax Modules
The SI3050-E-GT is suitable for a multifunction-printer fax or telephone module requiring an analog FXO path alongside digital document processing. Software programmability permits configuration of line behavior for the intended market, while the standard telephony PCM interface can connect the voice path to a dedicated modem, codec, or DSP. The isolation-capacitor approach used by the Si3050 family removes conventional isolation transformers, relays, and opto-isolators from the supported design, conserving board area in compact printer electronics. Engineering validation should include line-voltage protection, ring detection, hook-state timing, and the required Si3011/18/19 companion. Firmware must also support the exact installed SI3050 revision.
Được đề xuất
Digital PBX Peripheral Cards
A digital PBX peripheral card can use the SI3050-E-GT to add one or more analog FXO channels to a processor-based line-card design. The system-side device operates from 3.3 V and interfaces through a standard telephony PCM connection, allowing shared codecs and digital switching logic to handle the voice path. Programmable PTT behavior is especially useful for multi-country PBX installations because line supervision and regional requirements can be adjusted in software. The Si3050 family data sheet also describes compliance work covering high-voltage surges, emissions, immunity, out-of-band energy, and safety. Each analog channel still requires its designated Si3011, Si3018, or Si3019 line-side device and the associated protection network defined by the reference design.
Được đề xuất
Analog Caller-ID Systems
The SI3050-E-GT can support an analog caller-ID product that receives telephone-line signaling and passes voice information through a digital host interface. The system-side Voice DAA handles the programmable line interface, while the matching Si3011/18/19 companion performs the corresponding line-side functions. A PCM connection allows the caller-ID data and voice path to share the digital infrastructure of the product. Compliance with multiple PTT and immunity requirements is important because telephone products face line surges and out-of-band energy restrictions. The designer should use the family data sheet to configure signaling timing, country-specific behavior, and revision detection, and should preserve the recommended isolation-capacitor component placement.
Được đề xuất
Industrial Telephone Monitoring
The SI3050-E-GT is applicable to industrial telephone monitoring equipment that must detect and control an analog line while forwarding voice through a PCM-based system. Its software-programmable behavior helps standardize line supervision across installations operating in different regions. The 3.3 V host-side architecture integrates more naturally with modern embedded processors than a legacy 5 V interface design. The Si3050 family data sheet identifies coverage for FCC, TBR21, JATE, EN55022, EN55024, and high-voltage-surge requirements, providing useful guidance when qualifying a connected product. The implementation must include the appropriate line-side companion, protection components, grounding strategy, and isolation-capacitor layout. Firmware should identify the device revision through the documented REVA register field before applying configuration.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho SI3050-E-GT — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
Choose SI3050-E1-GT when that revision is the approved configuration and when the available firmware explicitly recognizes the E1 revision. Consider SI3050-E-FT or SI3050-E1-FT only after checking the associated revision, electrical characteristics, and software support. The FTR codes are relevant when reel packaging is required, but the ordering suffix should not be treated as a functional upgrade. Before releasing a design, verify lifecycle availability, the exact line-side companion, regional PTT configuration, protection network, and recommended isolation-capacitor layout.
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | SI3050-E1-GT | SI3050-E-FT | SI3050-E1-FT | SI3050-E1-FTR | SI3050-E-FTR |
|---|---|---|---|---|---|---|
| Brand | Silicon Labs | Silicon Labs | Silicon Labs | Silicon Labs | Silicon Labs | Silicon Labs |
| Package | 20-pin TSSOP | 20-pin TSSOP - same | 20-pin TSSOP - same | 20-pin TSSOP - same | 20-pin TSSOP - same | 20-pin TSSOP - same |
| Product Type | Programmable Voice Direct Access Arrangement | Programmable Voice Direct Access Arrangement | Programmable Voice Direct Access Arrangement | Programmable Voice Direct Access Arrangement | Programmable Voice Direct Access Arrangement | Programmable Voice Direct Access Arrangement |
| Supply Voltage | 3.3 V | 3.3 V | 3.3 V | 3.3 V | 3.3 V | 3.3 V |
| Digital Interface | Standard telephony PCM interface | Standard telephony PCM interface | Standard telephony PCM interface | Standard telephony PCM interface | Standard telephony PCM interface | Standard telephony PCM interface |
| Line-Side Companion | Si3011, Si3018, or Si3019 | Si3011, Si3018, or Si3019 | Si3011, Si3018, or Si3019 | Si3011, Si3018, or Si3019 | Si3011, Si3018, or Si3019 | Si3011, Si3018, or Si3019 |
| Ordering Code Revision | Revision E | Revision E1 | Revision F | Revision E1/F ordering code | Revision E1/F ordering code | Revision F |
| Programming Method | Software programmable | Software programmable | Software programmable | Software programmable | Software programmable | Software programmable |
| Isolation Architecture | Patented isolation capacitor technology | Patented isolation capacitor technology | Patended isolation capacitor technology | Patented isolation capacitor technology | Patended isolation capacitor technology | Patended isolation capacitor technology |
Bảo phân biệt quan trọng
- Directly specified as revision E in the ordering code (vsSI3050-E1-GT)
- Legacy-friendly 20-pin TSSOP footprint (vsSI3050-E-FT)
- Global programmable Voice DAA architecture (vsSI3050-E1-FTR)
Ghi chú thiết kế
Implement the Si3050 and Si3011/18/19 line-side circuit using the isolation-capacitor placement and grounding arrangement shown in the family data sheet. Keep the telephone-line side physically separated from host-side PCM and power routing, use the prescribed protection network, and avoid long unprotected copper paths. This isolation strategy is central to the family's ability to replace transformers, relays, and opto-isolators while meeting global line-interface requirements.
Route PCM clock and data traces as controlled-impedance digital signals, with the SI3050 placed to minimize trace length to the host codec or DSP. Decouple the 3.3 V supply locally and maintain continuous ground references between the digital section and the Voice DAA support components. Pay particular attention to clock jitter and grounding return paths because the telephone side and host side share a compact 20-pin TSSOP implementation.
Do not treat a different SI3050 suffix as automatically interchangeable. Confirm the device revision through the documented REVA[3:0] register field, select the matching Si3011, Si3018, or Si3019 line-side companion, and load a configuration approved for the target country. Revision E, E1, and F ordering codes can share the 20-pin TSSOP footprint while differing in device identity and configuration requirements.
Validate the complete telephone-interface design rather than only the SI3050-E-GT itself. Check hook-state thresholds, ring detection, line current, off-hook timing, PTT behavior, surge immunity, emissions, and isolation capacitance using the family data sheet tables and reference circuits. A host-side PCM test can pass even when line-side timing or regional protection requirements remain incorrect.
Thông tin tuân thủ
The exact SI3050-E-GT ordering record is identified as lead-free. The family data sheet documents FCC, TBR21, JATE, FCC Parts 15 and 68, EN55022, EN55024, surge, emissions, immunity, and safety requirements. No RoHS, REACH, halogen-free, or conflict-minerals statement is confirmed for the exact ordering code.