SN74LS244N - Octal 3-State Buffer | Texas Instruments
MPN: SN74LS244N ✓ Hoạt độngSN74LS244N Tóm tắt
A logic buffer is a digital IC that reproduces a binary input signal at its output while providing buffering, drive strength, or controlled isolation between circuit sections. The SN74LS244N belongs to the 74LS low-power Schottky TTL family and is categorized as a non-inverting buffer or line driver. Its role in a larger logic hierarchy is to drive memory, clock, data, and other bus-oriented signals while placing each output into a high-impedance state when it is not selected.
The principal feature of the SN74LS244N is its combination of eight non-inverting channels and independently controlled 3-state outputs. A 5 V supply keeps the device compatible with conventional LS-TTL systems, while the two four-bit output groups support structured bus arrangements. The active-low output controls provide a straightforward way to isolate a driver during bus turnaround, address multiplexing, test, or shared-bus operation.
This device uses bipolar Schottky-clamped TTL technology. Its non-inverting buffers preserve input logic polarity, and the 3-state outputs offer a third electrical state in addition to high and low levels. That high-impedance state is essential when another circuit block must drive the same interconnect. Because the device is intended for 4.75 V to 5.25 V operation, system designers should account for the supply tolerance of older LS-TTL logic and the resulting margin at the ends of the voltage range.
Typical uses include driving address and data lines into dynamic memory, clock distribution within 5 V digital systems, bus buffering, and interfacing between modules that need controlled output isolation. The SN74LS244N is particularly useful where multiple buffered outputs must be released independently rather than disabled as one complete eight-channel group.
For reliable board-level implementation, connect each data input to its corresponding non-inverting output and use the active-low output-control pins to manage bus ownership. Keep unused inputs tied to a defined logic level and route supply and ground connections to provide adequate return paths. A complete pin assignment should be taken directly from the manufacturer pin-description table before laying out the PCB or wiring the device into legacy equipment.
This product record combines the manufacturer device description, distributor package information, cross-reference results, practical bus-design guidance, and a like-for-like comparison framework. It is intended to help engineers identify the correct 20-pin DIP replacement, distinguish electrically related logic families, and plan output-enable sequencing before committing a schematic or PCB change.
Bộ thay thế dễ dàng lắp đặt cho SN74LS244N — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với SN74LS244N (cùng hình factor và footprint) — khác nhau ở Logic Family, Package.
SN74S244N
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
SN74HCT244N
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
SN74ACT244N
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
SN74AHCT244N
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
DM74LS244N
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
SN74LS244N Tỷ lệ tối đa & tính chất điện
| Product Type | Octal non-inverting buffer and line driver |
| Logic Family | 74LS low-power Schottky TTL |
| Number of Channels | 8 channels |
| Channel Organization | 2 elements × 4 bits |
| Output Polarity | Non-inverting |
| Output State | 3-state, high-impedance |
| Supply Voltage Range | 4.75 V to 5.25 V |
| Output Control | Active low |
| Logic Family Technology | Bipolar Schottky TTL |
| Hộp | 20-pin DIP |
| Kiểu lắp đặt | Through-hole |
Hướng dẫn cấu hình chân SN74LS244N 20-pin dip
Cấu hình chân cho SN74LS244N (20-pin dip gói). IC số này bao gồm chân GPIO, giao diện truyền thông (UART, SPI, I2C) và chân nguồn. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết các chức năng chân thay thế và tùy chọn cấu hình. Cực kỳ quan trọng cho thiết kế hệ thống tích hợp và lập trình PCB.
Không có dữ liệu chân cụ thể sẵn có cho SN74LS244N.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
SN74LS244N phù hợp cho 6 Áp dụngs: Memory Address and Data Bus Buffering, Clock Distribution, Bidirectional Bus Interface Support, Legacy Computer and Test Equipment Repair, Industrial Control Module Isolation, Educational and Digital Logic Prototyping.
Memory Address and Data Bus Buffering
The SN74LS244N is suitable for buffering address or data lines in a 5 V LS-TTL system because it provides eight non-inverting channels and independent 3-state control. The device can place selected outputs in a high-impedance state during memory-bank selection, preventing two memory drivers from fighting over the same bus. Its 4.75 V to 5.25 V operating range matches the stated system supply. When planning the logic, verify propagation delay and output-current limits against the memory and backplane loading before treating the buffer as a complete timing solution.
Được đề xuất
Clock Distribution
The SN74LS244N can distribute a clock to several destinations while giving each output an active-low enable control. This allows selected clock loads to be connected or isolated during reset, test, or operating-mode changes. Its eight non-inverting channels are useful where a shared source must feed parallel counters, flip-flops, or memory-control logic in a 4.75 V to 5.25 V environment. Because clock networks are timing-sensitive, calculate cumulative buffer delay and check edge requirements against the slowest receiving device rather than relying only on nominal functional equivalence.
Được đề xuất
Bidirectional Bus Interface Support
The SN74LS244N fits systems that need controlled isolation around shared data paths, particularly when two independently enabled buffer banks feed a common bus. The 3-state output allows each channel to stop driving logically, while the non-inverting arrangement preserves data polarity from source to destination. Its 20-pin DIP package also supports repair and modernization of older 5 V computer, test, and industrial-control assemblies. Correct ownership logic is essential: only one driver group should be enabled at a time, and all unused inputs must remain in a defined state.
Được đề xuất
Legacy Computer and Test Equipment Repair
The SN74LS244N is a practical replacement candidate in legacy 5 V equipment that used an octal non-inverting 3-state buffer in a 20-pin DIP socket. Repairing a historical computer, peripheral, or instrumentation assembly often requires retaining the original logic-family timing instead of introducing a modern low-voltage device. The SN74LS244N provides the expected 74LS function and 4.75 V to 5.25 V supply operation. Before installation, compare every pin name and confirm that the replacement is not a surface-mount ordering code.
Được đề xuất
Industrial Control Module Isolation
The SN74LS244N can isolate logic outputs on an industrial control module by placing inactive channels in the high-impedance state. This is useful where a processor, programmable controller, or test fixture drives cards through shared connectors and must avoid contention during mode changes. The two four-bit groups provide structured control for paired buses, while active-low enables support straightforward control logic. The 4.75 V to 5.25 V range suits 5 V control electronics, but designers must include grounding, decoupling, and signal-integrity practices appropriate to the longer wiring paths commonly found in industrial systems.
Được đề xuất
Educational and Digital Logic Prototyping
The SN74LS244N supports classroom and prototype demonstrations of tristate logic, bus contention, output enable control, and non-inverting signal conditioning. Its 20-pin DIP package is easy to install on a solderless breadboard or socketed trainer board, while eight channels make bus behavior visible across multiple loads. The 5 V supply range aligns with conventional TTL teaching systems. Because incorrect output-enable sequencing can cause contention or undefined voltage, prototype each driver group separately and demonstrate the high-impedance state before connecting multiple external loads.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho SN74LS244N — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | SN74S244N | SN74HCT244N | SN74ACT244N | SN74AHCT244N | DM74LS244N |
|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | onsemi |
| Package | 20-pin DIP | 20-pin DIP | 20-pin DIP | 20-pin DIP | 20-pin DIP | 20-pin DIP |
| Function | Octal non-inverting 3-state buffer | Octal non-inverting 3-state buffer | Octal non-inverting 3-state buffer | Octal non-inverting 3-state buffer | Octal non-inverting 3-state buffer | Octal non-inverting 3-state buffer |
| Channel Count | 8 channels | 8 channels | 8 channels | 8 channels | 8 channels | 8 channels |
| Output Polarity | Non-inverting | Non-inverting | Non-inverting | Non-inverting | Non-inverting | Non-inverting |
| Logic Technology | Bipolar Schottky TTL | Bipolar Schottky TTL | CMOS with TTL-compatible inputs | Advanced CMOS | Advanced CMOS with TTL-compatible inputs | Bipolar Schottky TTL |
| Nominal Supply Voltage | 5 V | 5 V | 5 V | 5 V | 5 V | 5 V |
| Output Enable | Active low | Active low | Active low | Active low | Active low | Active low |
| Mounting Style | Through-hole | Through-hole | Through-hole | Through-hole | Through-hole | Through-hole |
| Primary Selection Trade-Off | Original 74LS timing and electrical behavior | Related Schottky TTL family behavior | TTL-compatible CMOS input behavior | Advanced CMOS speed and power behavior | Advanced CMOS with TTL-compatible inputs | Second-source 74LS behavior |
Bảo phân biệt quan trọng
- Retains the established bipolar 74LS operating characteristic (vsSN74HCT244N)
- Second-source option retains the same logic family and package (vsDM74LS244N)
- Two independently controlled four-bit groups (vsSN74S244N)
Ghi chú thiết kế
Do not allow two enabled outputs to drive the same bus line at the same time. The SN74LS244N can place outputs in a high-impedance state, but incorrect output-enable sequencing can still create contention, excessive current, and undefined voltage levels. Define the ownership of each four-bit group in the system logic and provide non-overlapping enable timing before connecting two driver sources to one interconnect.
Use the manufacturer pin-description table to assign every data input, output, ground, supply, and output-control connection before routing the 20-pin DIP. In a new layout, place the device near the protected bus, maintain short ground-return paths, and keep switching or high-current traces physically separate from buffer outputs. For a replacement board, follow the original component outline and socket orientation rather than relying on the logical function alone.
Account for propagation delay, input transition-time limits, capacitive loading, and the number of attached receivers when using the SN74LS244N as a bus driver. The 3-state output reduces contention when correctly disabled, but it does not eliminate trace impedance, ringing, or timing skew. For longer or faster interconnects, use controlled topology, appropriate termination, and measurement-based timing checks instead of assuming buffer functionality alone guarantees signal integrity.
Operate the SN74LS244N within its stated 4.75 V to 5.25 V supply range and verify the complete system’s voltage tolerance at the device pins. Provide a low-impedance supply and ground connection, particularly when several outputs are switching simultaneously. Because the package is a through-hole 20-pin DIP intended for conventional 5 V logic, do not substitute a low-voltage modern part without separately checking input thresholds, timing, and supply limits.
Thông tin tuân thủ
No specific RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declaration is stated in the product information. General-purpose logic status does not establish automotive qualification.