SN74LS642N - 8-Bit Open-Collector Bus Transceiver | TI
MPN: SN74LS642N ✓ Hoạt độngSN74LS642N Tóm tắt
A bus transceiver is a logic interface that connects two data buses and allows data to travel in either direction. The SN74LS642 belongs to the 74LS low-power Schottky TTL logic family and combines eight bidirectional bus channels with direction and enable control. Open-collector outputs are particularly useful when a bus requires pull-up resistors, wired-AND behavior, or compatibility with another logic family.
Key features include eight 1-bit transceiver elements, an inverting data path, open-collector output capability, a 4.75 V to 5.25 V operating range, 12 mA output-current capability, and Schmitt-trigger input behavior. The direction input determines which bus drives the other, while the enable input provides a common control for disabling the transceiver and reducing bus contention.
The device is designed for asynchronous, two-way communication between computer or peripheral buses. Its open-collector architecture requires correctly sized external pull-up resistors on each bus. Pull-up resistance, bus capacitance, sink-current capability, and maximum data rate must be considered together because increasing resistance reduces current demand but can slow bus transitions and increase susceptibility to noise.
Typical applications include bidirectional instrument buses, peripheral-interface isolation, test and measurement systems, computer data buses, and industrial control interfaces. In each case, the DIR input selects the transmitting direction, while G controls whether the enabled device participates in the bus transaction. The 20-pin PDIP package is suited to through-hole boards and legacy system maintenance.
For reliable operation, place pull-up resistors close to the open-collector outputs and keep the shared bus traces short enough to control ringing and crosstalk. Confirm that the external pull-up network can source the required receiver current without exceeding the device's output specifications. Do not enable opposing drivers on the same bus.
This page combines device architecture, package and pin information, replacement guidance, comparison criteria, and practical bus-interface design notes to support component selection and board-level implementation.
Bộ thay thế dễ dàng lắp đặt cho SN74LS642N — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
SN74LS642N
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →SN74LS642N
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →SN74LS642N
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →SN74LS642N
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →SN74LS642N
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →SN74LS642N Tỷ lệ tối đa & tính chất điện
| Product Type | Octal inverting bus transceiver |
| Number of Bits | 8 bits |
| Number of Elements | 1 element per 8-bit channel |
| Data Direction | Bidirectional, A bus to B bus or B bus to A bus |
| Logic Level | Inverting |
| Kiểu đầu ra | Open collector |
| Output Current | 12 mA |
| Input Feature | Schmitt trigger |
| Supply Voltage Range | 4.75 V to 5.25 V |
| Enable Control | G input for bus isolation |
| Direction Control | DIR input |
| Hộp | 20-pin PDIP |
| Kiểu lắp đặt | Through-hole |
Cấu hình chân SN74LS642N
| Chân 1 | 1A — A-side data terminal for channel 1 |
| Chân 2 | 2A — A-side data terminal for channel 2 |
| Chân 3 | 3A — A-side data terminal for channel 3 |
| Chân 4 | 4A — A-side data terminal for channel 4 |
| Chân 5 | GND — Ground reference |
| Chân 6 | DIR — Direction-control input |
| Chân 7 | G — Enable input used to disable the device and isolate the buses |
| Chân 8 | 8A — A-side data terminal for channel 8 |
| Chân 9 | 8B — B-side data terminal for channel 8 |
| Chân 10 | 7B — B-side data terminal for channel 7 |
| Chân 11 | 6B — B-side data terminal for channel 6 |
| Chân 12 | 5B — B-side data terminal for channel 5 |
| Chân 13 | 4B — B-side data terminal for channel 4 |
| Chân 14 | 3B — B-side data terminal for channel 3 |
| Chân 15 | 2B — B-side data terminal for channel 2 |
| Chân 16 | 1B — B-side data terminal for channel 1 |
| Chân 17 | VCC — Positive power-supply terminal |
| Chân 18 | 5A — A-side data terminal for channel 5 |
| Chân 19 | 6A — A-side data terminal for channel 6 |
| Chân 20 | 7A — A-side data terminal for channel 7 |
Ứng dụng tiêu biểu
SN74LS642N phù hợp cho 6 Áp dụngs: Bidirectional Instrument Bus, Computer Peripheral Bus Interface, Test and Measurement Control Interface, Industrial Control Bus, Legacy Peripheral Data Port, Bus Isolation and Direction Control.
Bidirectional Instrument Bus
The SN74LS642N fits legacy asynchronous instrument buses that need one transceiver to support communication in either direction. Its eight inverting channels are controlled by DIR, while G can disable the device when the bus must be isolated. The 4.75 V to 5.25 V supply range suits 5 V TTL systems, and the 12 mA output-current capability defines the available open-collector sink performance. External pull-up resistors are required on every open-collector data line. Select pull-up values from the bus capacitance, receiver current requirement, and maximum target transition rate, then verify timing across the full operating temperature range using the manufacturer electrical characteristics.
Được đề xuất
Computer Peripheral Bus Interface
The SN74LS642N can connect two asynchronous computer or peripheral buses when the surrounding logic expects inverted data and open-collector signaling. DIR establishes which side transmits, and G provides a common isolation control during bus turnaround. Its eight integrated channels reduce the number of discrete bus-interface components, while the 20-pin PDIP package supports straightforward through-hole assembly and legacy board maintenance. Because open-collector outputs do not actively source a high level, add pull-up resistors and keep their traces short. Validate contention behavior, receiver thresholds, and propagation delay before enabling the device in a multi-master arrangement.
Được đề xuất
Test and Measurement Control Interface
The SN74LS642N is appropriate for a test fixture or measurement controller that must exchange commands and results with an external instrument over a shared bus. Its DIR control supports asymmetric send and receive phases, and G can disconnect the transceiver during inactive periods to reduce contention. The inverting data path can simplify interfacing with negative-TTL or inverted-control logic, while the Schmitt-trigger inputs improve tolerance of slower transitions from cables or open-collector wiring. Use short, well-terminated traces where possible and derive pull-up values from the actual cable capacitance. Validate timing margins with the longest interconnect and the specified system operating environment.
Được đề xuất
Industrial Control Bus
The SN74LS642N can be used in a 5 V industrial control module when the field bus uses open-collector signaling and inverted logic. The DIR input permits controlled exchanges between a controller and peripheral, while G provides a hardware means of isolating the interface during reset or fault conditions. Its 20-pin PDIP format is useful for systems built on through-hole control boards and for maintenance of older equipment. Add suitable protection and pull-up networks at the connector, and verify that the 12 mA output-current capability remains compatible with every attached node. Check DIR and G sequencing in firmware so that two devices never attempt to drive the same line simultaneously.
Được đề xuất
Legacy Peripheral Data Port
The SN74LS642N suits a legacy peripheral data port where an 8-bit parallel path must operate bidirectionally at 5 V. Eight parallel channels provide a practical match to byte-oriented buses, and DIR can be driven by a peripheral select or address decoder. The G input may be tied to a qualified bus-enable signal so that the transceiver remains inactive while another device owns the shared bus. The open-collector outputs require external pull-up resistors, providing flexibility for mixed-family buses, but the chosen resistance must satisfy both sink-current and rise-time requirements. Confirm the inverting behavior at the system boundary and retain timing margins for the slowest valid bus transaction.
Được đề xuất
Bus Isolation and Direction Control
The SN74LS642N provides both direction selection and active bus isolation through its DIR and G controls, making it useful when multiple interface blocks share a communication line. During normal transfer, DIR determines the A-to-B or B-to-A path; during idle or fault intervals, G can disable the device so the buses are effectively isolated. This arrangement is especially helpful in systems requiring controlled bus turnaround rather than fixed one-way drivers. The open-collector architecture needs pull-up resistors on each line, and the design must avoid changing DIR while another node drives the same bus. Validate enable polarity and timing against the manufacturer data sheet and the external bus owner's control protocol.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho SN74LS642N — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | SN74LS642N | SN74LS642N | SN74LS642N | SN74LS642N | SN74LS642N |
|---|---|---|---|---|---|---|
| Package | 20-pin PDIP | 20-pin PDIP | 20-pin PDIP | 20-pin PDIP | 20-pin PDIP | 20-pin PDIP |
| Brand | Texas Instruments | Texas Instruments | onsemi | Motorola | International Rectifier | Rochester Electronics |
| Function | Octal inverting bus transceiver | Octal inverting bus transceiver | Octal inverting bus transceiver | Octal inverting bus transceiver | Octal inverting bus transceiver | Octal inverting bus transceiver |
| Number of Bits | 8 bits | 8 bits | 8 bits | 8 bits | 8 bits | 8 bits |
Bảo phân biệt quan trọng
- Bidirectional octal interface with integrated direction control (vsSN74LS641N)
- Open-collector bus output enables wired bus arrangements (vsSN74LS641N)
- Schmitt-trigger inputs improve tolerance of slow transitions (vsSN74LS641N)
- Established 20-pin PDIP format for through-hole legacy systems (vsSN74LS642NSRG4)
Ghi chú thiết kế
Place one external pull-up resistor on every open-collector data line and route each resistor close to the associated bus node. The resistor must source enough current for the receiver while keeping the bus rise time within the timing budget. Account for total bus capacitance, connector capacitance, and leakage current rather than selecting the resistance from receiver current alone.
Do not allow two enabled devices to drive the same open-collector line at the same time. Even though open-collector outputs can tolerate wired-AND behavior, incorrect DIR or G sequencing can corrupt data or exceed the available sink current. Define startup, arbitration, and turnaround states so that one node owns the bus before another begins driving it.
Keep the DIR and G control traces short and keep the eight data channels away from high-energy switching nodes. For cable-connected buses, minimize stub length and provide the appropriate connector protection. Verify signal integrity with the actual pull-up resistance and bus load because reducing resistance improves rise time but increases sink current.
The SN74LS642N operates in the 4.75 V to 5.25 V range, so its supply must remain within those limits under startup, load, and temperature conditions. Decouple the supply close to the VCC and GND pins according to the manufacturer guidance. Confirm that pull-up current and bus loading are included in the complete power-budget calculation rather than evaluating only the transceiver's own supply current.
Thông tin tuân thủ
Compliance status is not stated in the manufacturer product information or distributor records available for this product.