SN75154D - Quad RS-232 Receiver | Texas Instruments
MPN: SN75154D ✓ Hoạt độngSN75154D Tóm tắt
A differential line receiver is an interface IC that converts a pair of bipolar data-line voltages into a logic-level output. In the broader hierarchy, a line receiver belongs to an interface IC, a communications transceiver, and ultimately a semiconductor. The SN75154D is designed for relatively short, single-line, point-to-point interfaces where noise immunity, adjustable input thresholds, and fail-safe behavior are more important than the bidirectional functions provided by a full RS-232 transceiver.
The SN75154D provides four receiver channels, a 7 kΩ input resistance, adjustable input thresholds for fail-safe operation, and compatibility with the EIA/TIA-232-E voltage range. Its maximum data rate is 1 Mbit/s, making it suitable for conventional RS-232 links and other point-to-point signaling paths. The 5 V to 5.5 V supply range also supports integration with common 5 V digital systems.
The monolithic Schottky implementation combines four receivers in one package while maintaining the voltage thresholds expected by RS-232 equipment. Each differential input accepts an external signal pair and generates a corresponding logic output. Adjustable thresholds allow a system to bias the receiver toward a known state when the line is undriven, supporting fail-safe interface behavior without relying solely on external components.
Typical uses include industrial serial links, point-to-point data equipment, peripheral interfaces, embedded control systems, and legacy RS-232 test equipment. The device can also work with a separate line driver in systems that require transmission and reception but do not need a single combined transceiver package.
For reliable implementation, maintain the voltage limits and input-threshold conditions specified by the manufacturer datasheet, place bypass capacitance close to the supply pins, and route differential inputs to minimize differential pickup. Because the SN75154D provides receivers only, a suitable line driver is required wherever the same equipment must transmit over the RS-232 interface.
This page combines package, interface, application, and design guidance with drop-in comparison information. It also identifies the key electrical parameters that should be checked before replacing an existing quadruple differential line receiver, helping engineers evaluate footprint compatibility, signal logic, supply voltage, temperature range, and fail-safe threshold behavior together.
Bộ thay thế dễ dàng lắp đặt cho SN75154D — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với SN75154D (cùng hình factor và footprint) — khác nhau ở Package, Operating Temperature Range, Internal Technology, Product Type, Supply Voltage Range.
SN75152D
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
SN75153D
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
SN75156D
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
SN75157D
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →SN75158D
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →SN75154D Thông số kỹ thuật
| Product Type | Quadruple differential RS-232 line receiver |
| Receiver Channels | 4 channels |
| Logic Levels | 4 output channels |
| Maximum Data Rate | 1 Mbit/s |
| Nominal Supply Voltage | 5 V |
| Supply Voltage Range | 5 V to 5.5 V |
| Minimum Logic Voltage | 5 V |
| Input Resistance | 7 kΩ |
| Khoảng nhiệt độ hoạt động | 0°C to 70°C |
| Hộp | SOIC-16 (D) |
| Số chân | 16 pins |
| Kiểu lắp đặt | Surface mount |
| Interface Standard | ANSI EIA/TIA-232-E |
| Recommendation | ITU V.28 |
| Input Threshold | Adjustable for fail-safe operation |
| Internal Technology | Monolithic low-power Schottky line receiver |
| ESD HBM Rating | 0 kV |
| Trạng thái RoHS | Compliant |
Hướng dẫn cấu hình chân SN75154D soic-16 (d)
Cấu hình chân cho SN75154D (soic-16 (d) gói). Số thứ tự chân, chức năng và sơ đồ kết nối được xác định trong tài liệu thông số kỹ thuật của nhà sản xuất. Tham khảo nó để biết footprint và hướng dẫn hàn chính xác.
Không có dữ liệu chân cụ thể sẵn có cho SN75154D.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
SN75154D phù hợp cho 6 Áp dụngs: Industrial RS-232 Point-to-Point Links, Data-Terminal and Communication Equipment, Embedded Control and Peripheral Interfaces, Legacy Serial Port Consolidation, Instrumentation and Test Equipment, Fail-Safe Serial Command Interfaces.
Industrial RS-232 Point-to-Point Links
The SN75154D fits equipment that receives RS-232 signals over short, point-to-point links and requires four receiver channels on a common 5 V rail. Its four differential inputs, 5 V to 5.5 V operating range, and 1 Mbit/s maximum data rate support conventional data-terminal and data-communication interfaces. Adjustable input thresholds can establish predictable fail-safe output states when a cable is disconnected. A separate line driver is required for the transmit path, while the receiving system should account for cable length, ground reference, and threshold selection.
Được đề xuất
Data-Terminal and Communication Equipment
The SN75154D is designed for the data-terminal and data-communication interface defined by ANSI EIA/TIA-232-E, making it appropriate for equipment that exchanges legacy serial signals with a host system. Four receiver channels allow several independently wired links to share one package. The 7 kΩ input resistance and adjustable threshold capability provide defined operating behavior across the EIA/TIA-232-E input-voltage range. Board-level implementation should preserve the recommended input network and provide local supply bypassing to minimize coupling between adjacent channels.
Được đề xuất
Embedded Control and Peripheral Interfaces
The SN75154D can receive four differential serial signals in an embedded controller or peripheral subsystem that retains compatibility with RS-232 equipment. Its 16-pin SOIC package is practical for compact mixed-signal boards, while the 5 V supply and logic levels align with conventional digital control systems. The 1 Mbit/s capability provides ample margin for many control and status channels. Because the device receives only, the system must include a separate transmitter when command information must travel back over the interface.
Được đề xuất
Legacy Serial Port Consolidation
The SN75154D is useful when four legacy serial receivers must be consolidated into one interface IC without introducing a mixed transceiver footprint. Its four independent differential receiver channels offer a direct way to distribute incoming RS-232 signals to digital logic. The 16-pin SOIC package allows placement beside a controller or connector, but differential input routing should remain short and appropriately terminated. Verify connector-side voltage protection independently because the receiver specification and external transient protection requirements are separate design constraints.
Được đề xuất
Instrumentation and Test Equipment
The SN75154D suits instrumentation that must acquire several low-speed or moderate-speed differential control signals from remote test equipment over RS-232-compatible wiring. Four channels reduce the number of receiver packages required for a multi-axis or multi-instrument interface, and the specified 1 Mbit/s rate supports many status and control links. Adjustable thresholds are useful when defining behavior for an open cable. Confirm the 0°C to 70°C operating range against the intended enclosure temperature and provide stable 5 V regulation close to the device.
Được đề xuất
Fail-Safe Serial Command Interfaces
The SN75154D is appropriate for command interfaces where a disconnected cable must leave each receiver in a defined state. Its adjustable input thresholds allow the system to bias the differential receiver inputs toward fail-safe operation rather than relying only on an external network. Four channels support multiple command or interlock lines while retaining the 16-pin SOIC footprint and 5 V operation. Threshold components should be selected from the manufacturer guidance, and system tests should cover unplugged, shorted, noisy, and powered-but-inactive cable conditions.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho SN75154D — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | SN75152D | SN75153D | SN75156D | SN75157D | SN75158D |
|---|---|---|---|---|---|---|
| Package | SOIC-16 (D) | SOIC-16 (D) | SOIC-16 (D) | SOIC-16 (D) | SOIC-16 (D) | SOIC-16 (D) |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Receiver Channels | 4 | 4 | 4 | 4 | 4 | 4 |
| Product Type | Quadruple differential RS-232 line receiver | Quadruple line receiver | Quadruple differential line receiver | Quadruple differential line receiver | Quadruple differential line receiver | Quadruple differential line receiver |
Bảo phân biệt quan trọng
- Four differential receivers in one 16-pin SOIC package (vsSN75152D)
- Explicit adjustable fail-safe input behavior (vsSN75153D)
- Specified 1 Mbit/s receiver performance (vsSN75156D)
- Seven-kilohm differential input resistance (vsSN75157D)
Ghi chú thiết kế
Place the power-supply bypass capacitor adjacent to the SN75154D supply pins and connect it directly to the ground reference. Route each differential input as a pair with closely matched geometry and adequate spacing from switching nodes. Because four receiver channels share one package, unequal routing between positive and negative conductors can convert common-mode interference into differential noise. Follow the manufacturer's pin and layout guidance when assigning the input network and grounding strategy.
Do not treat the SN75154D as a bidirectional transceiver: it contains four receivers and no RS-232 line drivers. Adding a separate driver is required when the equipment must transmit, and mixing driver and receiver supply or grounding errors can distort the received signal. Also verify output polarity and the inactive-state threshold before replacement because a common SOIC-16 footprint alone does not guarantee functional compatibility.
Use the adjustable input-threshold network to establish the required fail-safe logic state when the cable is open or the transmitter is inactive. Validate the selected threshold against the minimum and maximum receiver input voltages over the 0°C to 70°C operating range. Keep the threshold components close to their associated input pins and avoid long stubs that allow noise to couple differentially into the receiver.
Thông tin tuân thủ
RoHS compliance is indicated by component-listing information. No automotive qualification is indicated for this commercial-temperature RS-232 receiver. REACH, lead-free, halogen-free, and conflict-minerals declarations require confirmation from the manufacturer's current compliance documentation.