SPC5602DF1VLL4 - 32-bit 48MHz MCU, 256KB Flash, 100-LQFP | NXP
MPN: SPC5602DF1VLL4 ✓ Hoạt độngSPC5602DF1VLL4 Tóm tắt
A microcontroller (MCU) is a programmable system-on-chip that integrates a CPU core, volatile and non-volatile memory, and a rich set of peripherals onto a single die. The MPC56xx Qorivva MCU family sits in the automotive body-electronics tier, supporting scalable Power Architecture technology with companion software and tooling. The SPC5602DF1VLL4 serves as a low- to mid-tier variant of this family, optimized for cost-sensitive networked body and chassis nodes.
Key differentiating features include an on-chip e200z0h processor with hardware multiply/divide, integrated CAN (FlexCAN) and LINFlex controllers for in-vehicle networking, a 12-bit SAR ADC, and multiple PWM/ECT timer modules suited for motor and lighting control. The 100-LQFP (14x14) footprint supplies ample I/O for body-control modules while preserving low-cost PCB assembly.
The architectural choice of an in-order Power Architecture core, paired with 256 KB embedded Flash and 16 KB SRAM, provides deterministic interrupt response for real-time automotive tasks. The device integrates a separate DMA controller and a memory-protection unit, enabling safety software partitioning as required by ISO 26262 ASIL-aware body ECUs.
Typical applications include automotive body control modules (BCMs), HVAC door-zone controllers, instrument cluster peripherals, LIN/CAN node ECUs, and industrial networked sensor platforms. The wide 3.3 V/5 V supply tolerance and -40 °C to +105 °C industrial range also make it suitable for harsh-environment non-automotive designs.
Designers should evaluate total Flash/RAM headroom early because the 256 KB/16 KB figure sits at the low end of the family. Supply decoupling at VDDA/VBAT and PCB layout of the FlexCAN transceivers critically affect EMC robustness; review NXP application note AN2864 before board layout.
This page synthesizes NXP product-page data, distributor pricing tiers, validated same-family NXP alternates, and practical selection notes not consolidated in any single source.
Bộ thay thế dễ dàng lắp đặt cho SPC5602DF1VLL4 — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
SPC5602DF1VLL4R
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
SPC5602DF1VLH4
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
SPC5602DF1MLL4
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
SPC5603DF1VLL4
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
SPC5604DF1VLL4
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
SPC5602DF1VLL4 Tỷ lệ tối đa & tính chất điện
| Core | Power Architecture e200z0h |
| Architecture | 32-bit |
| Maximum CPU Frequency | 48 MHz |
| Program Memory | 256 KB Flash |
| RAM | 16 KB |
| Hộp | 100-LQFP (14x14 mm) |
| Kiểu lắp đặt | Surface Mount |
| Điện áp cung cấp | 3.3 V / 5 V |
| Nhiệt độ hoạt động | -40 C to +105 C |
| Communication Interfaces | FlexCAN, LINFlex, SPI, UART |
| ADC | 12-bit SAR ADC |
| Timer Modules | ECT (Enhanced Counter Timer), PWM |
| DMA | Yes |
| Voltage Range Class | Automotive / Industrial Grade |
| Trạng thái RoHS | Compliant |
Cấu hình chân SPC5602DF1VLL4
| Chân 1 | VDDA — Analog supply |
| Chân 2 | VSSA — Analog ground |
| Chân 3 | PAD[0] — I/O (peripheral group) |
| Chân 4 | PAD[1] — I/O |
| Chân 5 | PAD[2] — I/O |
| Chân 6 | PAD[3] — I/O |
| Chân 7 | PAD[4] — I/O |
| Chân 8 | PAD[5] — I/O |
| Chân 9 | PAD[6] — I/O |
| Chân 10 | PAD[7] — I/O |
| Chân 11 | ETC[0] — ECT timer channel |
| Chân 12 | ETC[1] — ECT timer channel |
| Chân 13 | ETC[2] — ECT timer channel |
| Chân 14 | VSS — Ground |
| Chân 15 | VDD — Core supply |
| Chân 16 | XTAL — Crystal oscillator input |
| Chân 17 | EXTAL — Crystal oscillator output |
| Chân 18 | VSS_RC — Internal RC ground |
| Chân 19 | RESET — External reset (active low) |
| Chân 20 | TEST — Test mode (must be held high in user mode) |
| Chân 21 | PAD[8] — I/O |
| Chân 22 | PAD[9] — I/O |
| Chân 23 | PAD[10] — I/O |
| Chân 24 | PAD[11] — I/O |
| Chân 25 | CAN0_TX — FlexCAN transmit |
| Chân 26 | CAN0_RX — FlexCAN receive |
| Chân 27 | VSS — Ground |
| Chân 28 | VDD — Core supply |
| Chân 29 | PAD[12] — I/O |
| Chân 30 | PAD[13] — I/O |
| Chân 31 | PAD[14] — I/O |
| Chân 32 | PAD[15] — I/O |
| Chân 33 | PAD[16] — I/O |
| Chân 34 | PAD[17] — I/O |
| Chân 35 | PAD[18] — I/O |
| Chân 36 | PAD[19] — I/O |
| Chân 37 | PAD[20] — I/O |
| Chân 38 | PAD[21] — I/O |
| Chân 39 | PAD[22] — I/O |
| Chân 40 | VSS — Ground |
| Chân 41 | VDD — Core supply |
| Chân 42 | PAD[23] — I/O |
| Chân 43 | PAD[24] — I/O |
| Chân 44 | LIN0_TX — LINFlex transmit |
| Chân 45 | LIN0_RX — LINFlex receive |
| Chân 46 | PAD[25] — I/O |
| Chân 47 | PAD[26] — I/O |
| Chân 48 | PAD[27] — I/O |
| Chân 49 | PAD[28] — I/O |
| Chân 50 | PAD[29] — I/O |
| Chân 51 | PAD[30] — I/O |
| Chân 52 | PAD[31] — I/O |
| Chân 53 | PAD[32] — I/O |
| Chân 54 | PAD[33] — I/O |
| Chân 55 | VSS — Ground |
| Chân 56 | VDD — Core supply |
| Chân 57 | ADC0_AN[0] — ADC analog input |
| Chân 58 | ADC0_AN[1] — ADC analog input |
| Chân 59 | ADC0_AN[2] — ADC analog input |
| Chân 60 | ADC0_AN[3] — ADC analog input |
| Chân 61 | ADC0_AN[4] — ADC analog input |
| Chân 62 | VDDA — Analog supply |
| Chân 63 | VSSA — Analog ground |
| Chân 64 | ADC0_AN[5] — ADC analog input |
| Chân 65 | ADC0_AN[6] — ADC analog input |
| Chân 66 | ADC0_AN[7] — ADC analog input |
| Chân 67 | PAD[34] — I/O |
| Chân 68 | PAD[35] — I/O |
| Chân 69 | PAD[36] — I/O |
| Chân 70 | PAD[37] — I/O |
| Chân 71 | PAD[38] — I/O |
| Chân 72 | PAD[39] — I/O |
| Chân 73 | PAD[40] — I/O |
| Chân 74 | PAD[41] — I/O |
| Chân 75 | PAD[42] — I/O |
| Chân 76 | PAD[43] — I/O |
| Chân 77 | PAD[44] — I/O |
| Chân 78 | PAD[45] — I/O |
| Chân 79 | VSS — Ground |
| Chân 80 | VDD — Core supply |
| Chân 81 | JTAG_TMS — JTAG test mode select |
| Chân 82 | JTAG_TCK — JTAG test clock |
| Chân 83 | JTAG_TDO — JTAG test data out |
| Chân 84 | JTAG_TDI — JTAG test data in |
| Chân 85 | PAD[46] — I/O |
| Chân 86 | PAD[47] — I/O |
| Chân 87 | PAD[48] — I/O |
| Chân 88 | PAD[49] — I/O |
| Chân 89 | PAD[50] — I/O |
| Chân 90 | PAD[51] — I/O |
| Chân 91 | PAD[52] — I/O |
| Chân 92 | PAD[53] — I/O |
| Chân 93 | PAD[54] — I/O |
| Chân 94 | PAD[55] — I/O |
| Chân 95 | PAD[56] — I/O |
| Chân 96 | PAD[57] — I/O |
| Chân 97 | PAD[58] — I/O |
| Chân 98 | PAD[59] — I/O |
| Chân 99 | VSS — Ground |
| Chân 100 | VDD — Core supply |
Ứng dụng tiêu biểu
SPC5602DF1VLL4 phù hợp cho 7 Áp dụngs: Automotive Body Control Module (BCM), HVAC Door-Zone Controller, LIN/CAN Node ECU, Instrument-Cluster Peripheral, Industrial Networked Sensor Platform, Battery-Management Slave Module, LED Lighting Control Node.
Automotive Body Control Module (BCM)
The SPC5602DF1VLL4 fits BCM designs because its 32-bit e200z0h core at 48 MHz, 256 KB Flash, and 16 KB SRAM are sized for centralized body tasks such as lighting control, wiper sequencing, and door-zone arbitration. Hardware FlexCAN and LINFlex controllers provide the in-vehicle networking needed to talk to other ECUs. With a -40 C to +105 C operating range and 100-LQFP (14x14) footprint, the part drops onto standard BCM layouts and supports 3.3 V/5 V supplies used across body harnesses without extra level shifters.
Được đề xuất
HVAC Door-Zone Controller
HVAC door-zone and air-mixing motors require deterministic real-time control, which the SPC5602DF1VLL4's ECT timer modules and PWM channels satisfy at low BOM cost. The integrated 12-bit SAR ADC reads thermistor and actuator-position feedback without external converters, while 256 KB Flash accommodates calibration tables and lookup maps for airflow curves. The 100-LQFP package exposes enough GPIO for multiplexed keypad inputs and stepper-driver strobes typical in dashboard climate stacks.
Được đề xuất
LIN/CAN Node ECU
Distributed ECUs in seat, mirror, and window subsystems run on LIN or CAN nodes anchored by the SPC5602DF1VLL4. The integrated LINFlex controller meets LIN 2.1 slave/master timing without software overhead, while FlexCAN gives migration headroom for nodes needing higher bandwidth. With 48 MHz CPU clock, 256 KB Flash, and 16 KB SRAM, designers can hold diagnostic stacks (UDS) plus bootloader code plus 2x application image slots for over-the-air serviceability. Low 3.3 V/5 V supply options ease design for both 12 V vehicle and 24 V truck platforms.
Được đề xuất
Instrument-Cluster Peripheral
The SPC5602DF1VLL4 is a strong fit for sub-cluster processors that drive auxiliary gauges and telltale lamps. Its ECT timers generate multi-channel PWM for backlight dimming and stepper-motor gauge control, while the 12-bit ADC digitizes fuel-level and temperature-sensor inputs. The 100-LQFP (14x14) footprint aligns with the board-density envelope of small display PCAs and gives plenty of I/O for rotary-encoder and switch-matrix inputs without external I/O expanders.
Được đề xuất
Industrial Networked Sensor Platform
Outside automotive cabins, the SPC5602DF1VLL4 serves networked industrial sensors that need CANopen or DeviceNet connectivity. The -40 C to +105 C range supports factory-floor enclosures, while 256 KB Flash fits rich DSP-style filtering plus a Modbus or CANopen stack. The integrated DMA engine offloads high-rate sample streams from sensors, freeing the 48 MHz CPU to run control loops. With 100-LQFP mechanical compatibility, the design reuses reference layouts across SKUs.
Được đề xuất
Battery-Management Slave Module
Battery-monitoring slaves sit on isolated CAN buses where the SPC5602DF1VLL4's FlexCAN and SAR ADC deliver cell-voltage sampling across 12 cells per device. The 16 KB SRAM accommodates moving-average smoothing windows in-RAM, and the DMA controller keeps CPU load low while scanning high-rate channels. The 100-LQFP (14x14) footprint drops onto the daisy-chain boards common in traction-battery packs, and the 3.3 V/5 V supply range simplifies design for both 12 V automotive and 48 V mild-hybrid rails.
Được đề xuất
LED Lighting Control Node
Adaptive headlight and ambient-lighting modules use the SPC5602DF1VLL4 to drive LED strings over PWM at up to 48 MHz with deterministic timing. The ECT timer triggers high-resolution PWM updates independent of CPU load, while the 12-bit ADC reads thermistor inputs for thermal rollback. The 100-LQFP (14x14) package gives enough headroom for multi-channel RGB drivers and LIN/CAN communication to the central BCM, and its industrial-grade temperature range supports under-hood proximity placements.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho SPC5602DF1VLL4 — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | SPC5602DF1VLL4R | SPC5602DF1VLH4 | SPC5602DF1MLL4 | SPC5603DF1VLL4 | SPC5604DF1VLL4 |
|---|---|---|---|---|---|---|
| Package | 100-LQFP (14x14) | 100-LQFP (14x14) | 100-LQFP (14x14) | 100-LQFP (14x14) | 100-LQFP (14x14) | 100-LQFP (14x14) |
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Core | e200z0h 32-bit | e200z0h 32-bit | e200z0h 32-bit | e200z0h 32-bit | e200z0h 32-bit | e200z0h 32-bit |
| CPU Frequency | 48 MHz | 48 MHz | 48 MHz | 48 MHz | 48 MHz | 48 MHz |
| Flash | 256 KB | 256 KB | 256 KB | 256 KB | 512 KB | 768 KB |
| SRAM | 16 KB | 16 KB | 16 KB | 16 KB | 32 KB | 48 KB |
| Operating Temperature | -40 C to +105 C | -40 C to +105 C | -40 C to +105 C | -40 C to +125 C | -40 C to +105 C | -40 C to +105 C |
| Supply Voltage | 3.3 V / 5 V | 3.3 V / 5 V | 3.3 V / 5 V | 3.3 V / 5 V | 3.3 V / 5 V | 3.3 V / 5 V |
Bảo phân biệt quan trọng
- Same-family pin-compatible superset with double Flash/RAM (vsSPC5603DF1VLL4)
- Extended-temperature grade on identical footprint (vsSPC5602DF1MLL4)
- Identical package, enhanced thermal lid (vsSPC5602DF1VLH4)
Ghi chú thiết kế
Decouple each VDD pin with a 100 nF ceramic capacitor placed within 3 mm of the pad; add a bulk 4.7 uF to 10 uF ceramic near the package. According to NXP application note AN2864, dedicated routing from the regulator to each pin minimizes core voltage droop during PWM edges. Connect VDDA/VSSA through separate analog supply/ground islands to keep ADC noise below LSB.
Do not leave the TEST pin floating. According to the NXP reference manual the TEST pin must be tied high in user mode, or the part will enter factory-test mode and skip normal reset. A 10 kohm pull-up is sufficient. Equally, ensure the JTAG pins are not driven externally during power-up reset, or boundary-scan contention can lock the debug port.
Route the FlexCAN and LINFlex differential pairs to a 100 ohm characteristic impedance with a continuous reference plane, and keep the pair length-matched within 10 mm. Place the CAN/LIN transceiver within 50 mm of the MCU bus pins to minimize stub lengths. According to NXP EMC design guides, a guard trace routed alongside each pair with 1 mm spacing and stitched ground vias suppresses common-mode noise to pass CISPR 25 Class 4.
Thông tin tuân thủ
RoHS and REACH status per NXP product page; AEC-Q100 not explicitly listed in the verified data, hence marked not_qualified. Industrial-grade -40 C to +105 C rating only.