STM32F051K6U6 - 48MHz Cortex-M0 MCU | STMicroelectronics
MPN: STM32F051K6U6 ✓ Hoạt độngSTM32F051K6U6 Tóm tắt
A microcontroller is a programmable semiconductor that integrates a processor core, memory, peripherals, and input/output interfaces on one device. The STM32F0 series belongs to the ARM Cortex-M0 class of embedded processors and operates within the broader hierarchy of microcontroller, embedded processor, semiconductor, and electronic control systems. Its compact package and 48 MHz performance make it suitable for cost-sensitive control boards, sensor nodes, and compact instruments.
The device provides 32 KB of Flash memory, an ARM Cortex-M0 core, and a 48 MHz maximum clock frequency. Its advertised peripheral set includes 11 timers, analog-to-digital and digital-to-analog converters, and communication interfaces. A 2.0 V to 3.6 V operating range supports common low-voltage embedded systems, while the 32-UFQFPN package reduces board area compared with larger leaded or fine-pitch MCU packages.
The STM32F051 architecture is organized around a 32-bit Cortex-M0 RISC core and an integrated peripheral set for timing, communication, and signal conversion. Timers support periodic and event-driven control, while ADC and DAC resources permit analog measurements and waveform generation without relying entirely on external converters. Serial interfaces can connect the MCU to sensors, transceivers, human-interface devices, and other embedded controllers.
Typical uses include industrial sensing modules, compact motor-control boards, building automation endpoints, communication transceivers, and low-cost data-acquisition products. The 32-pin package is particularly useful when board space is constrained but the design still requires mixed signal conversion and multiple communication functions rather than a minimal GPIO-only controller.
PCB design should preserve clean supply distribution and controlled return paths around the 5 mm x 5 mm package. Place decoupling capacitors close to the power pins, route sensitive analog signals away from switching nodes, and use the manufacturer pin-description table when assigning tracks. Confirm exposed-pad, programming, and debug connections against the package drawing before releasing the PCB.
This page combines the manufacturer specifications, package-focused engineering guidance, application selection criteria, and a parameter comparison of potential replacements. It also distinguishes true board-level drop-in candidates from related STM32 devices that require different packages or different peripheral assignments.
Bộ thay thế dễ dàng lắp đặt cho STM32F051K6U6 — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với STM32F051K6U6 (cùng hình factor và footprint) — khác nhau ở Package, Product Type, Flash Memory, Maximum CPU Frequency, Processor Core.
STM32F051K6U7
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →STM32F042K6U6
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →STM32F301K6U7
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →STM32F051K6T6
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →STM32F051K6U6 Tỷ lệ tối đa & tính chất điện
| Product Type | ARM Cortex-M0 32-bit microcontroller |
| Maximum CPU Frequency | 48 MHz |
| Flash Memory | 32 KB (32K x 8) |
| Supply Voltage Range | 2.0 V to 3.6 V |
| Processor Architecture | ARM Cortex-M0, 32-bit RISC |
| Timer Count | 11 timers |
| Analog Conversion Resources | ADC and DAC |
| Communication Interfaces | Serial communication interfaces |
| Hộp | 32-UFQFPN (5 mm x 5 mm) |
| Số chân | 32 pins |
| Kiểu lắp đặt | Surface mount |
| Series | STM32F0 |
| Manufacturer Family Flash Range | 16 KB to 64 KB |
Hướng dẫn cấu hình chân STM32F051K6U6 32-ufqfpn (5 mm x 5 mm)
Cấu hình chân cho STM32F051K6U6 (32-ufqfpn (5 mm x 5 mm) gói). IC số này bao gồm chân GPIO, giao diện truyền thông (UART, SPI, I2C) và chân nguồn. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết các chức năng chân thay thế và tùy chọn cấu hình. Cực kỳ quan trọng cho thiết kế hệ thống tích hợp và lập trình PCB.
Không có dữ liệu chân cụ thể sẵn có cho STM32F051K6U6.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
STM32F051K6U6 phù hợp cho 6 Áp dụngs: Compact Industrial Sensor Node, Low-Power Data Acquisition Module, Communication Transceiver Controller, Compact Motor and Relay Controller, Building Automation Endpoint, Portable Instrumentation and Test Equipment.
Compact Industrial Sensor Node
The STM32F051K6U6 fits compact industrial sensor nodes because its 48 MHz ARM Cortex-M0 core can process measurements and control logic while the 32 KB Flash provides room for embedded firmware. The integrated ADC supports analog sensor acquisition, and the 2.0 V to 3.6 V operating range is compatible with common 3.3 V industrial electronics. In a practical design, the MCU can sample sensors, apply filtering, evaluate thresholds, and publish results through a serial interface. The 32-UFQFPN package also reduces board area compared with larger MCU packages, although thermal grade, EMC isolation, and the exact exposed-pad layout must be validated for the deployment environment.
Được đề xuất
Low-Power Data Acquisition Module
The STM32F051K6U6 is suitable for a compact data-acquisition module that must combine sensor conditioning, control, and communications on one board. Its ADC resources can capture analog measurements, while the 48 MHz Cortex-M0 core handles scaling, filtering, buffering, and control tasks. The 32 KB Flash is appropriate for firmware, calibration tables, and configuration logic in a focused embedded design. Communications interfaces allow the module to forward results to a host processor or network interface. The principal design consideration is analog layout: keep the ADC input path away from switching nodes, provide a clean reference arrangement, and follow the manufacturer pin and grounding recommendations.
Được đề xuất
Communication Transceiver Controller
The STM32F051K6U6 can serve as the control processor in a small communication transceiver or protocol-conversion module. Its communication interfaces provide a path between external transceivers, configuration registers, and a host interface, while the 11 timers support timing, framing, timeout, and periodic maintenance functions. At 48 MHz, the Cortex-M0 core has sufficient throughput for lightweight protocol stacks without requiring a larger processor. Place the MCU and transceiver according to signal-integrity requirements, including a controlled reference plane, short return paths, and separation between sensitive communication routes and switching circuitry. Firmware and pin multiplexing must be validated for the selected transceiver interface.
Được đề xuất
Compact Motor and Relay Controller
The STM32F051K6U6 can control compact motors, relays, valves, and actuator boards because its 11 timers support timing-intensive control functions while ADC inputs enable current, position, or supply monitoring. The 32 KB Flash is sufficient for a focused embedded controller, and the 2.0 V to 3.6 V supply range integrates easily with common 3.3 V logic systems. In use, the MCU executes control loops, handles fault inputs, and coordinates actuator outputs through external drivers. Designers should not drive inductive loads directly from MCU pins; use suitable driver circuitry, protection networks, and low-inductance routing to prevent switching transients from affecting the processor and analog signals.
Được đề xuất
Building Automation Endpoint
The STM32F051K6U6 fits building-automation endpoints that combine digital inputs, analog sensing, scheduled control, and serial backhaul. Its 48 MHz Cortex-M0 core supports protocol handling and local logic, while the ADC can monitor environmental sensors and analog status inputs. The compact 5 mm x 5 mm UFQFPN package is useful in wall controllers and room modules where board area is restricted. The MCU can debounce inputs, execute scheduled actions, update outputs, and communicate status over a serial bus. Firmware should include communication timeouts and safe-state behavior, while the PCB should provide appropriate separation, surge accommodation, and grounding for connections extending beyond the enclosure.
Được đề xuất
Portable Instrumentation and Test Equipment
The STM32F051K6U6 is appropriate for compact instrumentation where an operator interface, measurement, and control functions must coexist in a limited board area. The ADC resources can acquire sensor or test-point voltages, the DAC can generate test stimuli, and the timers can manage measurement windows and repetitive operations. At 48 MHz with 32 KB Flash, the device supports a lightweight embedded user interface and control routine without a complex processor. The 32-pin package leaves a small board footprint, but careful analog grounding, input protection, and calibration are essential. Verify the ADC and DAC accuracy limits in the manufacturer datasheet and include calibration data when measurements require repeatable results.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho STM32F051K6U6 — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | STM32F051K6U7 | STM32F042K6U6 | STM32F301K6U7 | STM32F051K6T6 |
|---|---|---|---|---|---|
| Package | 32-UFQFPN (5x5) | 32-UFQFPN (5x5) | 32-UFQFPN (5x5) | 32-UFQFPN (5x5) | 32-UFQFPN (5x5) |
| Brand | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics |
| CPU Core | ARM Cortex-M0 | ARM Cortex-M0 | ARM Cortex-M0 | ARM Cortex-M0 | ARM Cortex-M0 |
| Flash Memory | 32 KB | 32 KB | 32 KB | 32 KB | 32 KB |
| Programming Interface | STM32F0 debugging and programming ecosystem | STM32F0 debugging and programming ecosystem | STM32 debugging and programming ecosystem | STM32 debugging and programming ecosystem | STM32F0 debugging and programming ecosystem |
Bảo phân biệt quan trọng
- Integrated mixed-signal resources (vsSTM32F042K6U6)
- Extended-temperature drop-in option (vsSTM32F051K6U7)
- Same-footprint consolidation within STM32F0 (vsSTM32F301K6U7)
Ghi chú thiết kế
Use the manufacturer package drawing as the controlling source for the 32-UFQFPN footprint. Place the MCU's decoupling capacitors adjacent to the corresponding power and ground pins, with short, low-loop connections and an uninterrupted ground plane. Connect the exposed pad according to the datasheet recommendation, including its copper area and thermal-via arrangement, because an incorrectly designed thermal pad can impair heat transfer or assembly reliability.
Route analog inputs and references away from digital clock lines, relay drivers, inductive components, and switching-power nodes. Keep the analog ground connection strategy consistent with the device recommendations, and avoid long shared paths between sensitive sources and the ADC pins. If the design uses the DAC to generate a test signal, treat the output as an analog source and preserve a quiet return path to the controlled load.
Confirm every SWD, boot, reset, and clock connection against the exact package pin table before routing. Maintain a continuous ground reference beneath high-speed or communication traces, avoid unnecessary test pads on sensitive analog nets, and separate external connector paths from MCU pins where surge or ESD transients could enter. Validate the final layout with signal-integrity and EMC testing rather than relying only on schematic connectivity.
Do not assume that every similarly named STM32F0 device is firmware- or peripheral-compatible. The STM32F051K6U6 has a defined 2.0 V to 3.6 V operating range, a specific 32-pin function assignment, and a 32 KB Flash configuration. Before substituting another order code, verify the package drawing, pin multiplexing, clock setup, peripheral availability, interrupt mapping, bootloader behavior, and temperature grade against the manufacturer documentation.
Thông tin tuân thủ
The reviewed manufacturer product information does not state explicit RoHS, REACH, lead-free, halogen-free, or conflict-minerals status for the exact order code. AEC-Q100 is not applicable to this general-purpose microcontroller ordering code.