STM32F051K6U6 - 48MHz Cortex-M0 MCU | STMicroelectronics
MPN: STM32F051K6U6 ✓ AktifSTM32F051K6U6 Ringkasan
A microcontroller is a programmable semiconductor that integrates a processor core, memory, peripherals, and input/output interfaces on one device. The STM32F0 series belongs to the ARM Cortex-M0 class of embedded processors and operates within the broader hierarchy of microcontroller, embedded processor, semiconductor, and electronic control systems. Its compact package and 48 MHz performance make it suitable for cost-sensitive control boards, sensor nodes, and compact instruments.
The device provides 32 KB of Flash memory, an ARM Cortex-M0 core, and a 48 MHz maximum clock frequency. Its advertised peripheral set includes 11 timers, analog-to-digital and digital-to-analog converters, and communication interfaces. A 2.0 V to 3.6 V operating range supports common low-voltage embedded systems, while the 32-UFQFPN package reduces board area compared with larger leaded or fine-pitch MCU packages.
The STM32F051 architecture is organized around a 32-bit Cortex-M0 RISC core and an integrated peripheral set for timing, communication, and signal conversion. Timers support periodic and event-driven control, while ADC and DAC resources permit analog measurements and waveform generation without relying entirely on external converters. Serial interfaces can connect the MCU to sensors, transceivers, human-interface devices, and other embedded controllers.
Typical uses include industrial sensing modules, compact motor-control boards, building automation endpoints, communication transceivers, and low-cost data-acquisition products. The 32-pin package is particularly useful when board space is constrained but the design still requires mixed signal conversion and multiple communication functions rather than a minimal GPIO-only controller.
PCB design should preserve clean supply distribution and controlled return paths around the 5 mm x 5 mm package. Place decoupling capacitors close to the power pins, route sensitive analog signals away from switching nodes, and use the manufacturer pin-description table when assigning tracks. Confirm exposed-pad, programming, and debug connections against the package drawing before releasing the PCB.
This page combines the manufacturer specifications, package-focused engineering guidance, application selection criteria, and a parameter comparison of potential replacements. It also distinguishes true board-level drop-in candidates from related STM32 devices that require different packages or different peripheral assignments.
Pilihan pengganti yang segera untuk STM32F051K6U6 — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.
Varietas dalam siri ini
Model serupa yang kompatibel dengan pengganti yang segera STM32F051K6U6 (sama faktor bentuk dan kaki) — berbeza dalam Package, Product Type, Flash Memory, Maximum CPU Frequency, Processor Core.
STM32F051K6U7
✅ Masuk Drop-InHubungi untuk harga
Lihat Datasheet →STM32F042K6U6
✅ Masuk Drop-InHubungi untuk harga
Lihat Datasheet →STM32F301K6U7
✅ Masuk Drop-InHubungi untuk harga
Lihat Datasheet →STM32F051K6T6
✅ Masuk Drop-In ⚠️ Spesifikasi Tidak DisahkanHubungi untuk harga
Lihat Datasheet →STM32F051K6U6 Penilaian maksimum & Ciri-ciri Elektrik
| Product Type | ARM Cortex-M0 32-bit microcontroller |
| Maximum CPU Frequency | 48 MHz |
| Flash Memory | 32 KB (32K x 8) |
| Supply Voltage Range | 2.0 V to 3.6 V |
| Processor Architecture | ARM Cortex-M0, 32-bit RISC |
| Timer Count | 11 timers |
| Analog Conversion Resources | ADC and DAC |
| Communication Interfaces | Serial communication interfaces |
| Kemasan | 32-UFQFPN (5 mm x 5 mm) |
| Kiraan Pin | 32 pins |
| Jenis Pemasangan | Surface mount |
| Series | STM32F0 |
| Manufacturer Family Flash Range | 16 KB to 64 KB |
Panduan Konfigurasi Pin STM32F051K6U6 32-ufqfpn (5 mm x 5 mm)
Konfigurasi pin untuk STM32F051K6U6 (32-ufqfpn (5 mm x 5 mm) pakai). IC digital ini termasuk GPIO, antaramuka komunikasi (UART, SPI, I2C), dan pin kuasa. Rujuk dokumen pengeluar untuk fungsi pin alternatif dan opsi konfigurasi. Biasa digunakan dalam rancangan sistem ter嵌入式 dan PCB.
Tiada data garisan pin yang diperoleh untuk STM32F051K6U6.
Rujuk kepada lembaran data untuk konfigurasi pin penuh.
Aplikasi Biasa
STM32F051K6U6 patut untuk 6 aplikasis: Compact Industrial Sensor Node, Low-Power Data Acquisition Module, Communication Transceiver Controller, Compact Motor and Relay Controller, Building Automation Endpoint, Portable Instrumentation and Test Equipment.
Compact Industrial Sensor Node
The STM32F051K6U6 fits compact industrial sensor nodes because its 48 MHz ARM Cortex-M0 core can process measurements and control logic while the 32 KB Flash provides room for embedded firmware. The integrated ADC supports analog sensor acquisition, and the 2.0 V to 3.6 V operating range is compatible with common 3.3 V industrial electronics. In a practical design, the MCU can sample sensors, apply filtering, evaluate thresholds, and publish results through a serial interface. The 32-UFQFPN package also reduces board area compared with larger MCU packages, although thermal grade, EMC isolation, and the exact exposed-pad layout must be validated for the deployment environment.
Disebarkan
Low-Power Data Acquisition Module
The STM32F051K6U6 is suitable for a compact data-acquisition module that must combine sensor conditioning, control, and communications on one board. Its ADC resources can capture analog measurements, while the 48 MHz Cortex-M0 core handles scaling, filtering, buffering, and control tasks. The 32 KB Flash is appropriate for firmware, calibration tables, and configuration logic in a focused embedded design. Communications interfaces allow the module to forward results to a host processor or network interface. The principal design consideration is analog layout: keep the ADC input path away from switching nodes, provide a clean reference arrangement, and follow the manufacturer pin and grounding recommendations.
Disebarkan
Communication Transceiver Controller
The STM32F051K6U6 can serve as the control processor in a small communication transceiver or protocol-conversion module. Its communication interfaces provide a path between external transceivers, configuration registers, and a host interface, while the 11 timers support timing, framing, timeout, and periodic maintenance functions. At 48 MHz, the Cortex-M0 core has sufficient throughput for lightweight protocol stacks without requiring a larger processor. Place the MCU and transceiver according to signal-integrity requirements, including a controlled reference plane, short return paths, and separation between sensitive communication routes and switching circuitry. Firmware and pin multiplexing must be validated for the selected transceiver interface.
Disebarkan
Compact Motor and Relay Controller
The STM32F051K6U6 can control compact motors, relays, valves, and actuator boards because its 11 timers support timing-intensive control functions while ADC inputs enable current, position, or supply monitoring. The 32 KB Flash is sufficient for a focused embedded controller, and the 2.0 V to 3.6 V supply range integrates easily with common 3.3 V logic systems. In use, the MCU executes control loops, handles fault inputs, and coordinates actuator outputs through external drivers. Designers should not drive inductive loads directly from MCU pins; use suitable driver circuitry, protection networks, and low-inductance routing to prevent switching transients from affecting the processor and analog signals.
Disebarkan
Building Automation Endpoint
The STM32F051K6U6 fits building-automation endpoints that combine digital inputs, analog sensing, scheduled control, and serial backhaul. Its 48 MHz Cortex-M0 core supports protocol handling and local logic, while the ADC can monitor environmental sensors and analog status inputs. The compact 5 mm x 5 mm UFQFPN package is useful in wall controllers and room modules where board area is restricted. The MCU can debounce inputs, execute scheduled actions, update outputs, and communicate status over a serial bus. Firmware should include communication timeouts and safe-state behavior, while the PCB should provide appropriate separation, surge accommodation, and grounding for connections extending beyond the enclosure.
Disebarkan
Portable Instrumentation and Test Equipment
The STM32F051K6U6 is appropriate for compact instrumentation where an operator interface, measurement, and control functions must coexist in a limited board area. The ADC resources can acquire sensor or test-point voltages, the DAC can generate test stimuli, and the timers can manage measurement windows and repetitive operations. At 48 MHz with 32 KB Flash, the device supports a lightweight embedded user interface and control routine without a complex processor. The 32-pin package leaves a small board footprint, but careful analog grounding, input protection, and calibration are essential. Verify the ADC and DAC accuracy limits in the manufacturer datasheet and include calibration data when measurements require repeatable results.
Disebarkan
Ringkasan Produk Disebarkan
Data referensi kejuruteraan untuk STM32F051K6U6 — perbandingan, panduan rancangan, dan maklumat kesediaan
Panduan Pilihan
Perbandingan dengan Gantian
| Parametr | Produk Ini | STM32F051K6U7 | STM32F042K6U6 | STM32F301K6U7 | STM32F051K6T6 |
|---|---|---|---|---|---|
| Package | 32-UFQFPN (5x5) | 32-UFQFPN (5x5) | 32-UFQFPN (5x5) | 32-UFQFPN (5x5) | 32-UFQFPN (5x5) |
| Brand | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics |
| CPU Core | ARM Cortex-M0 | ARM Cortex-M0 | ARM Cortex-M0 | ARM Cortex-M0 | ARM Cortex-M0 |
| Flash Memory | 32 KB | 32 KB | 32 KB | 32 KB | 32 KB |
| Programming Interface | STM32F0 debugging and programming ecosystem | STM32F0 debugging and programming ecosystem | STM32 debugging and programming ecosystem | STM32 debugging and programming ecosystem | STM32F0 debugging and programming ecosystem |
Penyeberangsung Jelas
- Integrated mixed-signal resources (vsSTM32F042K6U6)
- Extended-temperature drop-in option (vsSTM32F051K6U7)
- Same-footprint consolidation within STM32F0 (vsSTM32F301K6U7)
Catatan Desain
Use the manufacturer package drawing as the controlling source for the 32-UFQFPN footprint. Place the MCU's decoupling capacitors adjacent to the corresponding power and ground pins, with short, low-loop connections and an uninterrupted ground plane. Connect the exposed pad according to the datasheet recommendation, including its copper area and thermal-via arrangement, because an incorrectly designed thermal pad can impair heat transfer or assembly reliability.
Route analog inputs and references away from digital clock lines, relay drivers, inductive components, and switching-power nodes. Keep the analog ground connection strategy consistent with the device recommendations, and avoid long shared paths between sensitive sources and the ADC pins. If the design uses the DAC to generate a test signal, treat the output as an analog source and preserve a quiet return path to the controlled load.
Confirm every SWD, boot, reset, and clock connection against the exact package pin table before routing. Maintain a continuous ground reference beneath high-speed or communication traces, avoid unnecessary test pads on sensitive analog nets, and separate external connector paths from MCU pins where surge or ESD transients could enter. Validate the final layout with signal-integrity and EMC testing rather than relying only on schematic connectivity.
Do not assume that every similarly named STM32F0 device is firmware- or peripheral-compatible. The STM32F051K6U6 has a defined 2.0 V to 3.6 V operating range, a specific 32-pin function assignment, and a 32 KB Flash configuration. Before substituting another order code, verify the package drawing, pin multiplexing, clock setup, peripheral availability, interrupt mapping, bootloader behavior, and temperature grade against the manufacturer documentation.
Maklumat Kesediaan
The reviewed manufacturer product information does not state explicit RoHS, REACH, lead-free, halogen-free, or conflict-minerals status for the exact order code. AEC-Q100 is not applicable to this general-purpose microcontroller ordering code.