TCAN332DCNR - 3.3V 1Mbps CAN Transceiver | Texas Instruments
MPN: TCAN332DCNR ✓ Hoạt độngTCAN332DCNR Tóm tắt
A CAN transceiver is an interface IC that connects a host controller's digital logic to a differential CAN bus. Within the CAN interface hierarchy, the TCAN332 belongs to the physical-layer transceiver class, converting logic-level TXD and RXD signals into bus-level CANH and CANL signals and receiving bus data for the controller. Its 3.3 V supply operation suits modern embedded systems, while its low pin count assists compact industrial and automotive electronics designs.
Key features include support for CAN and CAN FD protocols, 1 Mbps maximum data rate, and receiver operation over common-mode input voltages from -2 V to 7 V. The TCAN332 family also provides low-power shutdown and standby operating modes for battery-powered or intermittently connected equipment. These characteristics make the device suitable where low supply voltage and compact packaging are more important than 5 V compatibility.
The device combines a CAN transmitter, CAN receiver, bus-driver protection, and digital interface functions in one package. Its DCN SOT-23 package reduces board area compared with larger SOIC options, although careful placement of input and bus components is important in systems with fast CAN edges or electrically noisy environments. The operating temperature range covers industrial temperature requirements from -40°C through +125°C.
Typical applications include industrial automation controllers, building automation nodes, battery-powered condition monitoring, electric-vehicle subsystems, robotics, and compact CAN-based sensor networks. The TCAN332DCNR is especially appropriate when the controller operates from a 3.3 V rail and the system requires CAN FD capability without a separate physical-layer transceiver.
Design with the manufacturer's recommended CAN bus protection and termination arrangements. Keep the transceiver close to the connector or bus stub, use a continuous ground reference beneath the bus route, and follow the datasheet layout guidance for decoupling capacitors and exposed-pad thermal management. Verify logic levels, loopback behavior, standby polarity, and bus fault handling in the final firmware.
This product page consolidates the exact package, electrical limits, protocol capabilities, drop-in alternatives, comparison parameters, and PCB guidance needed to evaluate the TCAN332DCNR for a 3.3 V CAN FD design.
Bộ thay thế dễ dàng lắp đặt cho TCAN332DCNR — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với TCAN332DCNR (cùng hình factor và footprint) — khác nhau ở Product Type, Operating Temperature Range, Package, Supply Voltage, Number of Channels.
TCAN330DCNR
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →TCAN331DCNR
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
TCAN334DCNT
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →TCAN1042DCNR
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
TCAN2302DCNR
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
TCAN332DCNR Thông số kỹ thuật
| Product Type | CAN FD transceiver |
| Điện áp cung cấp | 3.0 V to 3.63 V |
| Nominal Supply Voltage | 3.3 V |
| Maximum Data Rate | 1 Mbps |
| Supported Protocols | CAN and CAN FD |
| Number of Channels | 1 channel |
| Receiver Common-Mode Input Range | -2 V to 7 V |
| Khoảng nhiệt độ hoạt động | -40°C to +125°C |
| Hộp | 8-pin SOT-23 (DCN) |
| Số lượng chân | 8 pins |
| Kiểu lắp đặt | Surface mount |
| Power-Down and Standby Modes | Supported |
| Cấp MSL | MSL 1 at 260°C |
| MSL Duration | Unlimited |
| Trạng thái RoHS | Compliant |
Hướng dẫn cấu hình chân TCAN332DCNR 8-pin sot-23 (dcn)
Cấu hình chân cho TCAN332DCNR (8-pin sot-23 (dcn) gói). Số thứ tự chân, chức năng và sơ đồ kết nối được xác định trong tài liệu thông số kỹ thuật của nhà sản xuất. Tham khảo nó để biết footprint và hướng dẫn hàn chính xác.
Không có dữ liệu chân cụ thể sẵn có cho TCAN332DCNR.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
TCAN332DCNR phù hợp cho 6 Áp dụngs: Industrial Automation Controllers, Building Automation and HVAC Nodes, Battery-Powered Condition Monitoring, Electric Vehicle Subsystems, Robotics and Sensor Networks, CAN-Based Diagnostic Gateways.
Industrial Automation Controllers
The TCAN332DCNR fits industrial automation nodes that communicate over a 3.3 V CAN bus and may later add CAN FD-capable equipment. Its 3.0 V to 3.63 V supply range, 1 Mbps maximum data rate, and -40°C to +125°C operating range support controller, sensor-hub, and actuator-gateway designs in factory environments. The single-channel DCN package saves board area, while shutdown and standby modes help satisfy power-management targets. In a typical controller, the transceiver connects the CANH and CANL bus terminals to a local CAN controller and receives TXD and RXD logic signals. Designers should use the manufacturer-recommended decoupling and protection arrangements and verify that all field-bus timing remains compatible with the selected CAN FD network.
Building Automation and HVAC Nodes
TCAN332DCNR is appropriate for compact building-automation and HVAC controller modules that use a 3.3 V embedded processor and a shared CAN backbone. The 8-pin SOT-23 footprint preserves board area compared with larger transceivers, while CAN FD support provides protocol headroom for mixed building systems. Its 1 Mbps maximum data rate is suitable for common controller, damper, sensor, and gateway traffic. Place the transceiver near the bus connector or short bus stub, maintain a continuous ground reference, and apply the datasheet's recommended protection. Because standby and wake behavior influence building power budgets, the system firmware should coordinate the transceiver state with the host controller rather than treating the interface as continuously active.
Battery-Powered Condition Monitoring
The TCAN332DCNR supports compact battery-operated monitoring equipment that must communicate through a low-voltage CAN network. Its 3.3 V operating class, shutdown mode, and standby mode provide useful power-control options when measurements are taken intermittently. The -40°C to +125°C specification also supports equipment intended for wide environmental ranges. A typical implementation places the transceiver beside a low-power MCU and a protected CAN connector, allowing the controller to wake the network only when a measurement or diagnostic message must be transmitted. The shutdown and standby levels must be coordinated with the MCU's I/O voltages, and the complete node's sleep current should be measured because transceiver consumption alone does not determine the final battery life.
Electric Vehicle Subsystems
TCAN332DCNR can interface 3.3 V embedded controllers in electric-vehicle subsystems that use CAN FD, such as body, thermal-management, or seat electronics. Its 1 Mbps maximum data rate and wide -40°C to +125°C operating range fit many distributed control networks, while the compact DCN package supports dense electronics. The 3.0 V to 3.63 V supply range permits direct use with a regulated 3.3 V rail. In a vehicle installation, the designer must add the surge, ESD, load-dump, and transient protection required by the applicable OEM specification. The transceiver's -2 V to +7 V receiver common-mode range should not be treated as a substitute for external vehicle-bus protection.
Robotics and Sensor Networks
The TCAN332DCNR is useful in robot controllers, actuator modules, and distributed sensor networks where a CAN bus connects multiple nodes under a 3.3 V power budget. CAN FD support can improve payload efficiency compared with classic CAN, while the single-channel SOT-23 package leaves more PCB area for sensors or processing. The 1 Mbps rate and wide temperature range suit many compact industrial and mobile systems. Keep CAN routing away from high-current motor traces, provide a solid ground plane, and place protection close to external connectors. The host controller should verify nominal and fault-mode bus timing because a network that relies on 1 Mbps classic CAN operation must also remain compatible with the CAN FD-capable transceiver.
CAN-Based Diagnostic Gateways
TCAN332DCNR supports diagnostic gateways that translate between a 3.3 V host processor and an external CAN bus. Its CAN FD capability permits efficient transfer of diagnostic data, event logs, and configuration payloads while its 1 Mbps maximum data rate covers conventional CAN networks. The compact 8-pin DCN package helps gateways placed at the edge of machinery or vehicle systems. A gateway implementation should use the manufacturer's recommended ground and capacitor layout, confirm standby polarity, and include bus protection appropriate to the installation. If the gateway must remain in a low-power state while preserving diagnostics, coordinate the transceiver's shutdown or standby mode with the host wake strategy and verify recovery time before the first transmitted frame.
Dữ liệu tham khảo kỹ thuật cho TCAN332DCNR — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | TCAN330DCNR | TCAN331DCNR | TCAN334DCNT | TCAN1042DCNR | TCAN2302DCNR |
|---|---|---|---|---|---|---|
| Package | 8-pin SOT-23 (DCN) | 8-pin SOT-23 (DCN) | 8-pin SOT-23 (DCN) | 8-pin SOT-23 (DCN) | 8-pin SOT-23 (DCN) | 8-pin SOT-23 (DCN) |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Number of Channels | 1 channel | 1 channel | 1 channel | 1 channel | 1 channel | 1 channel |
Bảo phân biệt quan trọng
- CAN FD capability in a 3.3 V single-channel transceiver (vsTCAN330DCNR)
- Matches the 1 Mbps class of TCAN330DCNR while adding FD protocol support (vsTCAN330DCNR)
- Compact 8-pin SOT-23 integration with low-power control (vsTCAN1042DCNR)
Ghi chú thiết kế
Place the TCAN332DCNR close to the CAN connector or short bus stub and follow the manufacturer's DCN layout example for the input, output, and bypass capacitors. Keep the CANH and CANL route as a compact differential pair, avoid routing it alongside switching nodes, and provide a continuous ground reference beneath the bus path. This reduces external pickup and helps maintain predictable CAN signal integrity.
Decouple the 3.3 V transceiver supply locally and keep the return-current path short and low impedance. The device operates from 3.0 V to 3.63 V, so confirm that supply tolerance, startup droop, and transient behavior remain inside that range at the TCAN332DCNR pins. Coordinate standby and shutdown levels with the host controller so an undriven input cannot place the interface into an unintended operating state.
Do not substitute a classic-only CAN device when the connected network may transmit CAN FD frames, and do not assume a higher-speed TCAN variant is automatically preferable. Check protocol support, maximum data rate, recessive-dominant timing, standby polarity, fault behavior, and loopback timing against the complete system requirements. Reconfirm every DCN pin function before replacing the TCAN332DCNR.
The CAN bus is a differential physical-layer interface, but poor grounding or external protection placement can still introduce emissions and susceptibility problems. Use a short CANH-to-CANL route, avoid large loops, bond the interface ground to the main ground plane, and mount bus protection close to the connector. Apply termination only where required by the bus topology, following the manufacturer's guidance rather than adding arbitrary parallel resistance.
Thông tin tuân thủ
RoHS-compliant status and MSL 1 at 260°C unlimited floor-life information are identified for the TCAN332DCNR. Other compliance and qualification attributes require confirmation from the manufacturer.