THS3115ID - 110 MHz Dual Current-Feedback Amplifier | Texas Instruments
MPN: THS3115ID ✓ Hoạt độngTHS3115ID Tóm tắt
A current-feedback amplifier, or CFA, is a voltage-feedback amplifier architecture that uses feedback impedance to set gain and can maintain bandwidth more effectively than a conventional voltage-feedback amplifier across a wide gain range. In the broader electronics hierarchy, the THS3115ID is an operational amplifier, an analog signal-conditioning IC, and a semiconductor used in communication equipment, video distribution systems, motor drivers, and piezo drivers.
Each amplifier channel features low noninverting current noise of 2.9 pA/√Hz and low inverting current noise of 10.8 pA/√Hz. These current-noise levels are particularly useful when working with photodetectors, transducers, and other high-impedance sources because they limit the input-referred noise contributed by the amplifier. The 110 MHz bandwidth supports rapid signal transitions, while the high-output-current architecture is designed for loads requiring substantially greater drive than a conventional small-signal amplifier.
The THS3115 family also includes a low-power shutdown function that consumes only 300 µA of shutdown quiescent current per channel. Shutdown can reduce system consumption when an active signal path is not required, although timing, logic levels, and signal settling must be checked in the final application. Because a current-feedback amplifier does not follow the gain-versus-frequency behavior of a conventional voltage-feedback amplifier, its feedback resistor value is central to gain control and stability.
Typical uses include communication equipment, video distribution, motor drivers, and piezo drivers. The high-current output capability is particularly relevant when driving capacitive inputs such as coaxial cables, while the low-noise architecture benefits instrumentation and high-resolution signal chains. These applications also require careful attention to feedback networks, output-stage stability, power-supply bypassing, and grounding.
For a new design, begin with the manufacturer's recommended feedback resistor values for the intended gain and load, then verify stability with the actual source impedance, cable capacitance, and supply layout. Place bypass capacitors close to the supply pins and avoid long traces between the amplifier and sensitive input nodes. A PCB with a solid ground return and short feedback paths is especially important when operating near the device's 110 MHz bandwidth.
This product page consolidates the confirmed device characteristics, application guidance, package information, and available drop-in alternatives into an engineering-focused reference. It also identifies the data that still requires confirmation from the manufacturer datasheet, helping designers distinguish published facts from items that must be checked during component selection and board validation.
Bộ thay thế dễ dàng lắp đặt cho THS3115ID — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với THS3115ID (cùng hình factor và footprint) — khác nhau ở Package, Amplifier Type, Shutdown Function.
THS3115CDRG4
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
THS3112ID
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →THS3112CDRG4
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
THS3115ID Tỷ lệ tối đa & tính chất điện
| Amplifier Type | Current-feedback operational amplifier |
| Number of Channels | 2 channels |
| Gain-Bandwidth Product | 110 MHz |
| Noninverting Input Current Noise | 2.9 pA/√Hz |
| Inverting Input Current Noise | 10.8 pA/√Hz |
| Shutdown Quiescent Current | 300 µA per channel |
| Shutdown Function | Yes, low-power shutdown |
| Hộp | 14-pin SOIC (D), 3.90 mm width |
| Khoảng nhiệt độ hoạt động | -40°C to +85°C |
| Kiểu lắp đặt | Surface mount |
Hướng dẫn cấu hình chân THS3115ID 14-pin soic (d), 3.90 mm width
Cấu hình chân cho THS3115ID (14-pin soic (d), 3.90 mm width gói). Thành phần số hiệu này có chân đầu vào, đầu ra và nguồn cung cấp. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết cấu hình chân bù, bù trừ và chân kích hoạt. Hoàn hảo cho điều kiện tín hiệu và mạch khuếch đại.
Không có dữ liệu chân cụ thể sẵn có cho THS3115ID.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
THS3115ID phù hợp cho 6 Áp dụngs: Video Distribution, Motor Driver Signal Stage, Piezo Driver Interface, Communication Equipment, Low-Noise Instrumentation, General-Purpose High-Speed Buffer.
Video Distribution
The THS3115ID fits dual-channel video distribution because each channel provides a 110 MHz bandwidth and the family is specifically intended for high-output-current drive. The high-current capability helps retain signal integrity when driving terminated cables or other capacitive loads, while the dual configuration reduces the component count for two video channels. The 14-pin SOIC package is practical for conventional surface-mounted analog boards. During implementation, place the amplifier close to the source and load, keep feedback traces short, and include local supply bypassing. Cable capacitance, source impedance, and the required gain must be checked against the manufacturer stability guidance because high-speed current-feedback amplifiers can be sensitive to load and layout details.
Được đề xuất
Motor Driver Signal Stage
For motor-driver signal conditioning, the THS3115ID combines a 110 MHz bandwidth with the high-output-current capability highlighted for the THS3115 family. These characteristics are useful when the amplifier must preserve fast control edges while driving transistor input networks, gate-driver stages, or other relatively demanding loads. The dual-channel arrangement supports independent motor-control or feedback paths in one package. Design work should verify output swing, current limit, supply range, and capacitive loading in the exact gate-driver topology. Keep feedback loops compact, use a low-inductance ground return, and avoid long high-frequency traces that could increase ringing or reduce stability margin.
Được đề xuất
Piezo Driver Interface
The THS3115ID is suitable for the input stage of a piezo-driver circuit because its 110 MHz bandwidth supports rapid control signals and its high output current can provide stronger drive than a conventional small-signal amplifier. The dual format can handle a drive channel and a monitoring or feedback channel when the system architecture requires matched devices. Piezo loads are capacitive and frequency dependent, so the output stage must be checked for stability, peak current, and thermal load. Keep the amplifier-to-driver path short, use a ground plane with minimal return impedance, and evaluate the complete output network rather than treating the amplifier as an isolated voltage source.
Được đề xuất
Communication Equipment
The THS3115ID suits communication-equipment signal paths where low current noise, wide bandwidth, and high output drive are required. Its noninverting current noise of 2.9 pA/√Hz and inverting current noise of 10.8 pA/√Hz are valuable in source-impedance-sensitive receiver or transmitter interfaces. The dual 14-pin SOIC device provides two channels while keeping the footprint compact. Exact gain-bandwidth behavior depends on the current-feedback resistor selection, so use the manufacturer's recommended values rather than applying a conventional voltage-feedback gain formula. Keep input and feedback nodes compact, provide local supply bypass capacitance, and evaluate the design with the actual source impedance and cable loading.
Được đề xuất
Low-Noise Instrumentation
The THS3115ID can serve as a low-noise instrumentation amplifier in circuits that need to preserve small current signals from high-impedance sensors, transducers, or photodetectors. Its specified current-noise levels of 2.9 pA/√Hz and 10.8 pA/√Hz reduce amplifier-added input current noise, while the 110 MHz bandwidth provides headroom for filtering and signal shaping below that frequency. The shutdown capability can reduce consumption when measurement channels are inactive. Choose feedback resistors and noise-filtering networks according to the manufacturer guidance, maintain high-impedance leakage control on the PCB, and include sufficient input filtering to prevent wideband noise from reducing the usable measurement resolution.
Được đề xuất
General-Purpose High-Speed Buffer
The THS3115ID also functions as a high-speed buffer for test, measurement, and signal-conditioning systems requiring more output drive than a conventional small-signal amplifier. The 110 MHz bandwidth supports higher-frequency waveforms, and the dual configuration permits two independent buffered channels in one 14-pin SOIC package. When using either channel as a follower, verify the exact follower stability, output-current, and capacitive-load limits from the manufacturer documentation. Preserve short feedback paths, avoid placing large capacitors directly at the output unless the load is characterized, and use a continuous ground plane. The shutdown function can reduce power use when a test channel is not required, subject to the documented control timing.
Được đề xuất
Dữ liệu tham khảo kỹ thuật cho THS3115ID — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | THS3115CDRG4 | THS3112ID | THS3112CDRG4 |
|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 14-pin SOIC (D) | 14-pin SOIC (D) | 14-pin SOIC (D) | 14-pin SOIC (D) |
| Amplifier Type | Dual current-feedback operational amplifier | Dual current-feedback operational amplifier | Dual current-feedback operational amplifier | Dual current-feedback operational amplifier |
| Number of Channels | 2 channels | 2 channels | 2 channels | 2 channels |
Bảo phân biệt quan trọng
- Exact-family replacement candidate with confirmed package consistency (vsTHS3115CDRG4)
- Dual high-speed channels in a compact SOIC package (vsTHS3112ID)
- Low specified input current noise (vsTHS3112CDRG4)
- Defined low-power shutdown behavior (vsTHS3112ID)
Ghi chú thiết kế
Place the input, output, feedback, and bypass connections on the same PCB layer where practical. Keep feedback resistors and their associated input nodes compact to minimize parasitic inductance and capacitance at high frequency. Use a continuous ground plane and avoid routing sensitive input traces beneath noisy digital, switching, or power-conversion nodes. The 110 MHz bandwidth makes physical distance and return-path continuity significant even when the schematic appears simple.
Use the manufacturer-recommended supply and bypass configuration for the selected THS3115 ordering option. The confirmed 300 µA shutdown quiescent current per channel is a shutdown-state value, not the active operating current; active consumption depends on supply voltage, quiescent current, output swing, load, and frequency. Confirm those operating limits in the electrical-characteristics table before sizing the supply and calculating dissipation.
Do not calculate gain with the conventional voltage-feedback formula and then choose a feedback resistor independently of the source impedance. Current-feedback amplifiers require the recommended feedback resistance and often specific resistor values for target gains. Check the complete source, feedback, load, and cable network for stability. Large capacitive loads, long feedback loops, and mismatched source impedances can reduce phase margin or cause ringing.
Treat shutdown as a timed control signal rather than an ordinary static logic input. Confirm its polarity, assertion time, and output behavior from the manufacturer documentation. If the amplifier is disabled during a transition, its output may not follow the input normally. In systems that repeatedly enter and leave shutdown, include the timing in the system-level test plan and avoid sensitive nodes where shutdown transients could inject noise into downstream circuitry.
Thông tin tuân thủ
No explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals statements were available for the exact THS3115ID ordering option. Confirm these attributes on the manufacturer product and ordering pages before using the device in a regulated production design.