TLF35584QVHS2XUMA1 - ASIL-D PMIC | Infineon | OPTIREG
MPN: TLF35584QVHS2XUMA1 ✓ Hoạt độngTLF35584QVHS2XUMA1 Tóm tắt
An automotive safety PMIC is a highly integrated DC/DC and LDO regulator system designed to deliver deterministic, monitored power rails to safety-critical microcontrollers. PMICs belong to the broader power-management semiconductor category, alongside discrete DC-DC converters, LDOs, and battery management ICs. The TLF35584 family specifically targets ISO 26262 ASIL-D functional safety requirements, embedding window watchdog, error pin monitoring, fail-safe output state machine, and configurable reset behavior.
Key features include a primary step-down (buck) regulator for the microcontroller core, two auxiliary buck converters, a 5 V / 3.3 V LDO, a tracker/supply for off-board sensors, an SPI/parallel configuration interface, independent safety state machine, ABIST (logic BIST), and LBIST (ADC BIST) support, plus a dedicated error output to the host MCU. The wide 3.0 V to 40 V input range tolerates cranking transients and load-dump events on the automotive 12 V bus.
Architecturally the device combines synchronous buck converters, low-dropout regulators, and an integrated spread-spectrum oscillator to minimize EMI, while dedicated safety logic supervises undervoltage, overvoltage, watchdog timing, and thermal conditions. The exposed thermal pad and Grade 0 qualification allow direct placement near the microcontroller in safety-critical ECUs without secondary heatsinking.
Typical applications include AURIX TC3xx safety microcontrollers in electric power steering (EPS), airbag ECUs, ADAS domain controllers, brake controllers, and electrified powertrain ECUs. For multi-rail safety systems, the TLF35584 simplifies board design by replacing four to six discrete regulators and external supervisors with a single ASIL-D-capable IC.
When designing with this device, follow Infineon's recommended input bulk/ceramic capacitor network, observe SPI pull-up conventions, and verify the fail-safe state machine configuration with the TLF35584 safety manual. The error output pin must be routed to a host MCU interrupt for ASIL-D compliance.
Bộ thay thế dễ dàng lắp đặt cho TLF35584QVHS2XUMA1 — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với TLF35584QVHS2XUMA1 (cùng hình factor và footprint) — khác nhau ở Package, AEC-Q100 Qualification, Product Type.
TLF35584QVHS1
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
TLF35584QVHS2
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
TLE92633BQXXUMA2
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →TLE9180D32QKXUMA1
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →TLF35584QVHS2XUMA1 Tỷ lệ tối đa & tính chất điện
| Product Type | Multi-rail Automotive Safety PMIC (OPTIREG) |
| Input Voltage Range (operating) | 3.0 V to 40 V |
| Cấu hình đầu ra | 8 regulated outputs |
| Functional Safety Level | ISO 26262 ASIL-D (system-capable) |
| Hộp | PG-VQFN-48 (7 mm x 7 mm) with exposed thermal pad |
| Nhiệt độ mối nối hoạt động | -40 °C to +175 °C (Grade 0 automotive) |
| Số chân | 48 |
| Kiểu lắp đặt | Surface Mount |
| Configuration Interface | SPI / parallel |
| Integrated LDO Output | 3.3 V / 5 V selectable |
| Safety Features | Window watchdog, error pin, fail-safe state machine, ABIST, LBIST |
| Trạng thái RoHS | Compliant |
| AEC-Q100 Qualification | Qualified (Grade 0) |
| Primary Application | Automotive safety microcontrollers (e.g., AURIX TC3xx) |
Hướng dẫn cấu hình chân TLF35584QVHS2XUMA1 pg-vqfn-48 (7 mm x 7 mm) with exposed thermal pad
Cấu hình chân cho TLF35584QVHS2XUMA1 (pg-vqfn-48 (7 mm x 7 mm) with exposed thermal pad gói). Động cơ điện này có chân cổng, nguồn và đầu ra. Đối với các gói không phân極, tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết hướng dẫn chính xác của chân 1 và chi tiết về vân footprint. Các ứng dụng phổ biến bao gồm thiết kế nguồn cung cấp điện, điều khiển động cơ và chuyển đổi tải.
Không có dữ liệu chân cụ thể sẵn có cho TLF35584QVHS2XUMA1.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
TLF35584QVHS2XUMA1 phù hợp cho 6 Áp dụngs: Electric Power Steering (EPS) ECU, Airbag / Restraint Control Unit, ADAS Domain Controller, Brake Control (ABS/ESC) ECU, Electrified Powertrain Inverter ECU, Battery Management System (BMS) Master Controller.
Electric Power Steering (EPS) ECU
The TLF35584QVHS2XUMA1 is purpose-built to power AURIX TC3xx microcontrollers in electric power steering ECUs, where ISO 26262 ASIL-D is mandatory. Its 3.0 V to 40 V input tolerates load-dump and cranking transients on the 12 V vehicle bus, while the eight regulated rails deliver the core 1.3 V, 3.3 V, and 5 V supplies needed by the MCU, CAN transceivers, and sensor front-ends. The integrated window watchdog and fail-safe state machine meet ASIL-D decomposition requirements without an external supervisor, reducing PCB area in the steering column module.
Được đề xuất
Airbag / Restraint Control Unit
Airbag ECUs demand the highest functional-safety integrity (ASIL-D) and a deterministic supply rail. The TLF35584QVHS2XUMA1 delivers this with its integrated ABIST/LBIST self-tests, window watchdog, and dedicated error pin routed to the AURIX MCU interrupt. With Grade 0 / +175 °C junction temperature rating, it survives under-hood thermal stress without secondary heatsinking. Compared to a discrete regulator + supervisor solution, the TLF35584 cuts BOM count, simplifies safety case documentation, and shrinks the PCB footprint for the squib driver area.
Được đề xuất
ADAS Domain Controller
Centralized ADAS domain controllers based on AURIX TC3xx require multi-rail power with deterministic sequencing under all fault conditions. The TLF35584QVHS2XUMA1's eight configurable rails and SPI-controlled sequence give board designers full flexibility to power radar MCUs, camera SoCs, and Lidar processing nodes. The 40 V input tolerance handles transients on long wire harnesses, while the fail-safe state machine autonomously transitions the rails to a safe state if the host MCU stops servicing the watchdog - critical for fail-operational ADAS architectures targeting ASIL-D.
Được đề xuất
Brake Control (ABS/ESC) ECU
Anti-lock braking and electronic stability control ECUs operate in the harshest automotive environment, requiring ASIL-D power delivery and Grade 0 thermal performance. The TLF35584QVHS2XUMA1 powers the AURIX TC3xx MCU that runs the vehicle dynamics control loop, with the integrated window watchdog providing the dual-channel supervision required by ISO 26262. The exposed-pad PG-VQFN-48 package dissipates the device's full-load heat into the ECU housing copper, eliminating the need for a discrete heatsink in the brake module.
Được đề xuất
Electrified Powertrain Inverter ECU
In battery-electric and hybrid vehicles, the traction inverter ECU combines AURIX TC3xx with IGBT/SiC gate drivers and needs an ASIL-D multi-rail supply. The TLF35584QVHS2XUMA1 supplies the MCU core, gate-driver logic, and CAN-FD transceiver, while its SPI interface allows the MCU to dynamically enable/disable rails for low-voltage standby. With 3.0 V to 40 V input tolerance, the PMIC operates directly from the 12 V auxiliary battery, simplifying the HV-to-LV DC-DC stage and supporting functional-safety requirements for ASIL-D inverter control.
Được đề xuất
Battery Management System (BMS) Master Controller
In 400 V and 800 V EV battery packs, the BMS master controller uses AURIX TC3xx to manage cell balancing, state-of-charge, and isolation monitoring. The TLF35584QVHS2XUMA1 provides the deterministic multi-rail supply and ASIL-D safety supervision required by ISO 26262 for the battery pack controller. Its wide 3.0 V to 40 V input range allows direct connection to the 12 V low-voltage bus of the pack, and the fail-safe state machine guarantees the controller enters a safe state if the watchdog is not serviced.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho TLF35584QVHS2XUMA1 — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | TLF35584QVHS1 | TLF35584QVHS2 | TLE92633BQXXUMA2 | TLE9180D32QKXUMA1 |
|---|---|---|---|---|---|
| Package | PG-VQFN-48 (7x7 mm) | PG-VQFN-48 (same) | PG-VQFN-48 (same) | VQFN-48 family (different pinout) | VQFN-48 family (different pinout) |
| Brand | Infineon | Infineon | Infineon | Infineon | Infineon |
| Functional Safety Level | ASIL-D | ASIL-D | ASIL-D | ASIL-B | ASIL-D (gate driver PMIC) |
| Input Voltage Range | 3.0 V to 40 V | 3.0 V to 40 V | 3.0 V to 40 V | 4.5 V to 28 V | 3.0 V to 40 V |
| Number of Outputs | 8 | 8 | 8 | 3 | 5 |
| Junction Temperature | -40 to +175 °C (Grade 0) | -40 to +175 °C | -40 to +175 °C | -40 to +150 °C | -40 to +150 °C |
| Window Watchdog | Yes (integrated) | Yes | Yes | No | No (gate-driver PMIC) |
| Configuration Interface | SPI / parallel | SPI / parallel | SPI / parallel | SPI | SPI |
Bảo phân biệt quan trọng
- Integrated ASIL-D safety with 8 rails vs typical 3-4 rails (vsTLE92633BQXXUMA2)
- Dedicated safety PMIC vs multi-function gate-driver PMIC (vsTLE9180D32QKXUMA1)
- Grade 0 thermal headroom vs Grade 1 (vsTLE92633BQXXUMA2)
Ghi chú thiết kế
Estimated: at VIN=13.5 V with the device supplying the full AURIX TC3xx core + peripherals (~5 W total output power), the TLF35584QVHS2XUMA1 dissipates approximately 1.5 W internally. The PG-VQFN-48 package requires a copper pour area of at least 2 cm² on the top layer connected to the exposed pad, plus thermal vias to an inner/outer plane, to keep the junction rise within Grade 0 limits at +175 °C ambient corner. Inadequate copper results in thermal shutdown and reset loops.
Place the input bulk capacitor (≥10 µF ceramic + 47 µF electrolytic) within 5 mm of the VIN pin to suppress load-dump transients. Keep the buck-switching node traces short and use a 4-layer PCB with a continuous ground plane below the PMIC to minimize EMI. The exposed thermal pad must be soldered with via arrays (0.3 mm drill, 0.6 mm pitch) per Infineon application note recommendations.
Always initialize the TLF35584 over SPI on every MCU boot and service the window watchdog in the correct time window - missing the service window triggers the fail-safe state machine and may latch the outputs off. The error pin (ERR) must be routed to a host MCU interrupt, not a GPIO. Refer to the Infineon safety manual for the required ASIL-D diagnostic coverage and dual-channel watchdog configuration.
Thông tin tuân thủ
AEC-Q100 Grade 0 qualified per Infineon product page. ISO 26262 ASIL-D system-capable with integrated safety features. RoHS and REACH compliant.
