TLV2241IP - 12V 5.5kHz RRIO Op Amp | Texas Instruments
MPN: TLV2241IP ✓ Hoạt độngTLV2241IP Tóm tắt
An operational amplifier is a voltage-gain and signal-conditioning component used in the analog signal path. Its place in the device hierarchy is operational amplifier, analog amplifier, amplifier IC, integrated circuit, and semiconductor. The TLV2241IP supports common-mode input and output operation near the supply rails, which helps preserve signal range in low-voltage systems where the available input and output swing is limited.
The TLV2241 family provides very low supply current, extremely low input bias current, a typical offset voltage as low as 600 uV, 100 dB CMRR, and a minimum open-loop gain of 100 V/mV at a 2.7 V supply. The 5.5 kHz gain-bandwidth product supports low-frequency precision, sensing, and signal-conditioning tasks without the power requirements of a higher-bandwidth amplifier.
Its rail-to-rail input stage accepts signals extending toward the positive and negative supply rails. The low input bias current makes the amplifier suitable for high-impedance sources and applications using megaohm-class resistors. Open-loop gain of at least 100 V/mV provides useful DC loop gain, while the 100 dB CMRR helps reject common-mode voltage in battery-powered and industrial measurement circuits.
Typical applications include portable sensor interfaces, battery monitoring, low-current transducers, industrial measurement systems, and low-speed control loops. Its 1 uA-class supply current is especially useful when the amplifier must remain continuously powered alongside sensors, while the 5.5 kHz bandwidth is appropriate for signals that do not require high-speed video or communications performance.
Design should account for the limited gain-bandwidth product when selecting feedback resistors and closed-loop gain. The 8-pin PDIP footprint provides through-hole assembly and straightforward prototyping, while the wide supply and input ranges support low-voltage single-supply operation. Confirm the complete pin description and operating limits against the manufacturer datasheet before final PCB implementation.
Bộ thay thế dễ dàng lắp đặt cho TLV2241IP — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với TLV2241IP (cùng hình factor và footprint) — khác nhau ở Amplifier Type, Mounting Type, Package.
TLV2241IPE4
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
TLV2241IPG4
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
TLV2241IP Tỷ lệ tối đa & tính chất điện
| Amplifier Type | Single operational amplifier |
| Maximum Supply Voltage | 12 V |
| Nominal Single-Supply Voltage | 2.5 V |
| Gain-Bandwidth Product | 5.5 kHz |
| Điện áp cung cấp | Approximately 1 uA per channel |
| Input Bias Current | Extremely low; numerical value not stated |
| Typical Offset Voltage | As low as 600 uV |
| Common-Mode Rejection Ratio | 100 dB |
| Minimum Open-Loop Gain | 100 V/mV at 2.7 V |
| Input Common-Mode Range | Rail-to-rail |
| Output Swing | Rail-to-rail |
| Khoảng nhiệt độ hoạt động | -40 C to +125 C |
| Hộp | 8-pin PDIP (P) |
| Package Pin Count | 8 pins |
| Package Row Spacing | 7.62 mm |
| Kiểu lắp đặt | Through-hole |
Hướng dẫn cấu hình chân TLV2241IP 7.62 mm
Cấu hình chân cho TLV2241IP (7.62 mm gói). Thành phần số hiệu này có chân đầu vào, đầu ra và nguồn cung cấp. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết cấu hình chân bù, bù trừ và chân kích hoạt. Hoàn hảo cho điều kiện tín hiệu và mạch khuếch đại.
Không có dữ liệu chân cụ thể sẵn có cho TLV2241IP.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
TLV2241IP phù hợp cho 6 Áp dụngs: Battery-Powered Sensor Conditioning, Portable Medical and Industrial Measurements, Low-Current Power Monitoring, High-Impedance Transducer Interface, Portable Test and Measurement Equipment, Low-Speed Industrial Control Loops.
Battery-Powered Sensor Conditioning
The TLV2241IP fits low-power sensor interfaces because it operates from a 2.5 V single supply and draws approximately 1 uA per channel. Place the amplifier close to the sensor and conditioning network to limit susceptible trace length and preserve the small available signal range. Rail-to-rail input and output operation helps use much of the supply voltage, while the 5.5 kHz gain-bandwidth product is appropriate for temperature, pressure, and position signals that change slowly. The principal trade-off is bandwidth: applications requiring rapid settling or high-frequency content need a faster amplifier.
Được đề xuất
Portable Medical and Industrial Measurements
The TLV2241IP supports portable measurement systems that combine a low supply voltage with long battery life. Its approximately 1 uA supply current, 100 dB CMRR, and typical offset voltage as low as 600 uV help preserve small differential signals from field sensors. The amplifier can operate from a 2.5 V supply, and its rail-to-rail I/O characteristic reduces the voltage lost near the rails. Because the gain-bandwidth product is only 5.5 kHz, use it for slow physiological, environmental, or process signals rather than wideband waveforms.
Được đề xuất
Low-Current Power Monitoring
The TLV2241IP can amplify a scaled voltage representing battery or power-supply current for low-energy monitoring equipment. Its approximately 1 uA supply current keeps amplifier overhead small relative to the monitored system, and the 2.5 V minimum nominal supply supports compact single-rail designs. A 5.5 kHz closed-loop bandwidth is sufficient for slow current changes and threshold detection. When the monitored signal is differential, use the amplifier with a suitable low-side or high-side current-sense circuit and verify that its input common-mode range remains valid.
Được đề xuất
High-Impedance Transducer Interface
The extremely low input bias current of the TLV2241 family makes the TLV2241IP relevant to high-impedance transducers and very high-value feedback networks. A biased noninverting amplifier can use megaohm-class resistors while the amplifier's bias current introduces less disturbance to the source. The 100 dB CMRR helps reject common-mode noise, and rail-to-rail input operation supports low-voltage sensing. Keep the 5.5 kHz bandwidth limit in mind because high-value feedback networks also increase sensitivity to parasitic capacitance and noise.
Được đề xuất
Portable Test and Measurement Equipment
The TLV2241IP is useful in handheld meters and low-power test equipment that require accurate amplification of slow input signals. Its 12 V maximum supply, low offset voltage, 100 dB CMRR, and approximately 1 uA supply current balance measurement precision with portable power budgets. Rail-to-rail operation is useful when the front end uses a low-voltage sensor reference. Configure the feedback network for the intended closed-loop gain, and verify settling time if the meter must respond quickly after a range or input change.
Được đề xuất
Low-Speed Industrial Control Loops
The TLV2241IP can serve as the error amplifier in a low-speed industrial control loop when the process bandwidth is modest. Its high DC open-loop gain, low typical offset, and 100 dB CMRR support accurate regulation around a slow reference, while the micropower operating current helps limit standby consumption. The single 2.5 V nominal supply and rail-to-rail I/O simplify operation from compact sensor and actuator rails. Ensure loop crossover remains below the 5.5 kHz gain-bandwidth limit and include compensation appropriate to the feedback network and output loading.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho TLV2241IP — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | TLV2241IPE4 | TLV2241IPG4 |
|---|---|---|---|
| Package | 8-pin PDIP (P) | 8-pin PDIP | 8-pin PDIP |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
| Maximum Supply Voltage | 12 V | 12 V | 12 V |
| Nominal Single-Supply Voltage | 2.5 V | 2.5 V | 2.5 V |
| Gain-Bandwidth Product | 5.5 kHz | 5.5 kHz | 5.5 kHz |
| Supply Current | Approximately 1 uA per channel | Approximately 1 uA per channel | Approximately 1 uA per channel |
| Input and Output Operation | Rail-to-rail | Rail-to-rail | Rail-to-rail |
| Operating Temperature Range | -40 C to +125 C | -40 C to +125 C | -40 C to +125 C |
| Circuit Configuration | Single operational amplifier | Single operational amplifier | Single operational amplifier |
| Mounting Type | Through-hole | Through-hole | Through-hole |
Bảo phân biệt quan trọng
- Micropower operation supports long-life portable designs (vsTLV2241IPE4)
- Rail-to-rail operation improves low-voltage signal utilization (vsTLV2241IPG4)
- DC precision is suitable for low-speed measurement paths (vsTLV2241IPE4)
Ghi chú thiết kế
Use the approximately 1 uA per channel supply-current rating as the amplifier's baseline power estimate. For example, Estimated: a 2.5 V supply with 1 uA amplifier current corresponds to approximately 2.5 nW of amplifier supply power before load and divider currents. Add the current drawn by feedback resistors and downstream loads when sizing the source, and confirm that the source remains within the device's 12 V maximum supply rating.
Keep the feedback network and signal route compact because the TLV2241IP has a 5.5 kHz gain-bandwidth product. High-value feedback resistors can increase sensitivity to parasitic capacitance, leakage, and noise. For slow-signal applications, place the amplifier close to the source, use guarded or shielded routing when leakage matters, and test the completed board across the intended supply range and temperature range.
Design the PCB around the exact 8-pin PDIP pin assignment in the manufacturer datasheet. Maintain short, direct connections for the input, output, supply, and ground pins, especially when the amplifier drives capacitive loads or senses high-impedance sources. Place power-bypass capacitors close to the supply pins and route return current without sharing long paths with sensitive input signals.
Do not treat rail-to-rail input/output as unlimited dynamic range under every load condition. Check output swing, capacitive loading, stability, and input common-mode limits using the datasheet's test conditions. Also avoid assuming that the TLV2241IP can drive a fast-moving waveform merely because it can amplify low-frequency signals; its 5.5 kHz bandwidth and associated settling behavior must satisfy the application.
Thông tin tuân thủ
Compliance attributes were not identified in the retrieved product records. Confirm RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals status using the current Texas Instruments product documentation and the applicable orderable suffix.