TLV2241IP - 12V 5.5kHz RRIO Op Amp | Texas Instruments
料号: TLV2241IP ✓ 量产中TLV2241IP 概述
An operational amplifier is a voltage-gain and signal-conditioning component used in the analog signal path. Its place in the device hierarchy is operational amplifier, analog amplifier, amplifier IC, integrated circuit, and semiconductor. The TLV2241IP supports common-mode input and output operation near the supply rails, which helps preserve signal range in low-voltage systems where the available input and output swing is limited.
The TLV2241 family provides very low supply current, extremely low input bias current, a typical offset voltage as low as 600 uV, 100 dB CMRR, and a minimum open-loop gain of 100 V/mV at a 2.7 V supply. The 5.5 kHz gain-bandwidth product supports low-frequency precision, sensing, and signal-conditioning tasks without the power requirements of a higher-bandwidth amplifier.
Its rail-to-rail input stage accepts signals extending toward the positive and negative supply rails. The low input bias current makes the amplifier suitable for high-impedance sources and applications using megaohm-class resistors. Open-loop gain of at least 100 V/mV provides useful DC loop gain, while the 100 dB CMRR helps reject common-mode voltage in battery-powered and industrial measurement circuits.
Typical applications include portable sensor interfaces, battery monitoring, low-current transducers, industrial measurement systems, and low-speed control loops. Its 1 uA-class supply current is especially useful when the amplifier must remain continuously powered alongside sensors, while the 5.5 kHz bandwidth is appropriate for signals that do not require high-speed video or communications performance.
Design should account for the limited gain-bandwidth product when selecting feedback resistors and closed-loop gain. The 8-pin PDIP footprint provides through-hole assembly and straightforward prototyping, while the wide supply and input ranges support low-voltage single-supply operation. Confirm the complete pin description and operating limits against the manufacturer datasheet before final PCB implementation.
直接替换替代料: TLV2241IP ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: TLV2241IP (相同外形与封装尺寸) ——差异在于 Amplifier Type, Mounting Type, Package.
TLV2241IPE4
✅ 直接替换📋 参考替代料(不在目录中)
TLV2241IPG4
✅ 直接替换📋 参考替代料(不在目录中)
TLV2241IP 最大额定值与电气特性
| Amplifier Type | Single operational amplifier |
| Maximum Supply Voltage | 12 V |
| Nominal Single-Supply Voltage | 2.5 V |
| Gain-Bandwidth Product | 5.5 kHz |
| 电源电流 | Approximately 1 uA per channel |
| Input Bias Current | Extremely low; numerical value not stated |
| Typical Offset Voltage | As low as 600 uV |
| Common-Mode Rejection Ratio | 100 dB |
| Minimum Open-Loop Gain | 100 V/mV at 2.7 V |
| Input Common-Mode Range | Rail-to-rail |
| Output Swing | Rail-to-rail |
| 工作温度范围 | -40 C to +125 C |
| 封装 | 8-pin PDIP (P) |
| Package Pin Count | 8 pins |
| Package Row Spacing | 7.62 mm |
| 安装类型 | Through-hole |
TLV2241IP 7.62 mm 引脚配置指南
TLV2241IP(7.62 mm 封装)的引脚配置。 该模拟元件具有输入、输出和电源引脚。请参阅制造商数据手册以了解失调调零、补偿和使能引脚配置。适用于信号调理和放大器电路。
暂无详细引脚数据: TLV2241IP.
请参阅 数据手册 以查看完整引脚配置。
典型应用
TLV2241IP 适用于 6 应用s: Battery-Powered Sensor Conditioning, Portable Medical and Industrial Measurements, Low-Current Power Monitoring, High-Impedance Transducer Interface, Portable Test and Measurement Equipment, Low-Speed Industrial Control Loops.
Battery-Powered Sensor Conditioning
The TLV2241IP fits low-power sensor interfaces because it operates from a 2.5 V single supply and draws approximately 1 uA per channel. Place the amplifier close to the sensor and conditioning network to limit susceptible trace length and preserve the small available signal range. Rail-to-rail input and output operation helps use much of the supply voltage, while the 5.5 kHz gain-bandwidth product is appropriate for temperature, pressure, and position signals that change slowly. The principal trade-off is bandwidth: applications requiring rapid settling or high-frequency content need a faster amplifier.
推荐
Portable Medical and Industrial Measurements
The TLV2241IP supports portable measurement systems that combine a low supply voltage with long battery life. Its approximately 1 uA supply current, 100 dB CMRR, and typical offset voltage as low as 600 uV help preserve small differential signals from field sensors. The amplifier can operate from a 2.5 V supply, and its rail-to-rail I/O characteristic reduces the voltage lost near the rails. Because the gain-bandwidth product is only 5.5 kHz, use it for slow physiological, environmental, or process signals rather than wideband waveforms.
推荐
Low-Current Power Monitoring
The TLV2241IP can amplify a scaled voltage representing battery or power-supply current for low-energy monitoring equipment. Its approximately 1 uA supply current keeps amplifier overhead small relative to the monitored system, and the 2.5 V minimum nominal supply supports compact single-rail designs. A 5.5 kHz closed-loop bandwidth is sufficient for slow current changes and threshold detection. When the monitored signal is differential, use the amplifier with a suitable low-side or high-side current-sense circuit and verify that its input common-mode range remains valid.
推荐
High-Impedance Transducer Interface
The extremely low input bias current of the TLV2241 family makes the TLV2241IP relevant to high-impedance transducers and very high-value feedback networks. A biased noninverting amplifier can use megaohm-class resistors while the amplifier's bias current introduces less disturbance to the source. The 100 dB CMRR helps reject common-mode noise, and rail-to-rail input operation supports low-voltage sensing. Keep the 5.5 kHz bandwidth limit in mind because high-value feedback networks also increase sensitivity to parasitic capacitance and noise.
推荐
Portable Test and Measurement Equipment
The TLV2241IP is useful in handheld meters and low-power test equipment that require accurate amplification of slow input signals. Its 12 V maximum supply, low offset voltage, 100 dB CMRR, and approximately 1 uA supply current balance measurement precision with portable power budgets. Rail-to-rail operation is useful when the front end uses a low-voltage sensor reference. Configure the feedback network for the intended closed-loop gain, and verify settling time if the meter must respond quickly after a range or input change.
推荐
Low-Speed Industrial Control Loops
The TLV2241IP can serve as the error amplifier in a low-speed industrial control loop when the process bandwidth is modest. Its high DC open-loop gain, low typical offset, and 100 dB CMRR support accurate regulation around a slow reference, while the micropower operating current helps limit standby consumption. The single 2.5 V nominal supply and rail-to-rail I/O simplify operation from compact sensor and actuator rails. Ensure loop crossover remains below the 5.5 kHz gain-bandwidth limit and include compensation appropriate to the feedback network and output loading.
推荐
推荐产品汇总
工程参考数据: TLV2241IP ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | TLV2241IPE4 | TLV2241IPG4 |
|---|---|---|---|
| Package | 8-pin PDIP (P) | 8-pin PDIP | 8-pin PDIP |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
| Maximum Supply Voltage | 12 V | 12 V | 12 V |
| Nominal Single-Supply Voltage | 2.5 V | 2.5 V | 2.5 V |
| Gain-Bandwidth Product | 5.5 kHz | 5.5 kHz | 5.5 kHz |
| Supply Current | Approximately 1 uA per channel | Approximately 1 uA per channel | Approximately 1 uA per channel |
| Input and Output Operation | Rail-to-rail | Rail-to-rail | Rail-to-rail |
| Operating Temperature Range | -40 C to +125 C | -40 C to +125 C | -40 C to +125 C |
| Circuit Configuration | Single operational amplifier | Single operational amplifier | Single operational amplifier |
| Mounting Type | Through-hole | Through-hole | Through-hole |
关键差异点
- Micropower operation supports long-life portable designs (对比 TLV2241IPE4)
- Rail-to-rail operation improves low-voltage signal utilization (对比 TLV2241IPG4)
- DC precision is suitable for low-speed measurement paths (对比 TLV2241IPE4)
设计说明
Use the approximately 1 uA per channel supply-current rating as the amplifier's baseline power estimate. For example, Estimated: a 2.5 V supply with 1 uA amplifier current corresponds to approximately 2.5 nW of amplifier supply power before load and divider currents. Add the current drawn by feedback resistors and downstream loads when sizing the source, and confirm that the source remains within the device's 12 V maximum supply rating.
Keep the feedback network and signal route compact because the TLV2241IP has a 5.5 kHz gain-bandwidth product. High-value feedback resistors can increase sensitivity to parasitic capacitance, leakage, and noise. For slow-signal applications, place the amplifier close to the source, use guarded or shielded routing when leakage matters, and test the completed board across the intended supply range and temperature range.
Design the PCB around the exact 8-pin PDIP pin assignment in the manufacturer datasheet. Maintain short, direct connections for the input, output, supply, and ground pins, especially when the amplifier drives capacitive loads or senses high-impedance sources. Place power-bypass capacitors close to the supply pins and route return current without sharing long paths with sensitive input signals.
Do not treat rail-to-rail input/output as unlimited dynamic range under every load condition. Check output swing, capacitive loading, stability, and input common-mode limits using the datasheet's test conditions. Also avoid assuming that the TLV2241IP can drive a fast-moving waveform merely because it can amplify low-frequency signals; its 5.5 kHz bandwidth and associated settling behavior must satisfy the application.
合规信息
Compliance attributes were not identified in the retrieved product records. Confirm RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals status using the current Texas Instruments product documentation and the applicable orderable suffix.