TLV2244ID - Quad 12V Micropower Op Amp | Texas Instruments
MPN: TLV2244ID ✓ Hoạt độngTLV2244ID Tóm tắt
An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its two inputs while providing high input impedance and low output impedance. Operational amplifiers form the foundation of the amplifier IC hierarchy and support functions such as buffering, sensing, filtering, instrumentation, feedback control, and signal conditioning. The TLV2244 combines four amplifier channels in one package, reducing board area compared with four separate single-channel devices.
The TLV2244ID provides rail-to-rail input and output operation, allowing signals to use most of the available supply-voltage range without requiring conventional mid-supply biasing. Its low supply current of approximately 1 uA per channel is valuable in battery-powered equipment, while the 5.5 kHz gain-bandwidth product is appropriate for low-frequency precision and measurement circuits rather than high-speed signal processing.
Because the gain bandwidth is modest, stable operation depends on selecting feedback components and compensation appropriate for the intended closed-loop bandwidth. The amplifier can be used with resistive feedback networks, and applications requiring precision offset or drift performance should verify those limits against the manufacturer datasheet before production release. Rail-to-rail behavior also requires attention because input and output stages approach the supply rails through different structures.
Typical uses include low-frequency sensor conditioning, portable instrumentation, battery-powered monitoring, current-voltage signal interfaces, active filters, and four-channel measurement systems. In each case, the low channel current supports power-constrained operation, while the quad configuration reduces the component count when four independent amplifier functions are required.
For PCB implementation, keep input and feedback paths short, provide a stable supply connection, and place input biasing or decoupling components close to their associated pins. Verify stability with the actual source impedance, load, output capacitance, and gain configuration. Use the manufacturer pin-description table when assigning PCB tracks because the complete pin map is not reproduced on this page.
This product page combines the official device description, package and low-power characteristics, application-focused engineering guidance, and a selection framework for engineers evaluating the TLV2244ID against other micropower operational amplifiers.
Bộ thay thế dễ dàng lắp đặt cho TLV2244ID — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
TLV2264IP
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
TLV2274IP
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
TLV2474IP
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
TLV2464IP
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
TLV2244ID Tỷ lệ tối đa & tính chất điện
| Amplifier Type | Quad general-purpose operational amplifier |
| Number of Channels | 4 channels |
| Supply Voltage Range | 2.5 V to 12 V |
| Maximum Supply Voltage | 12 V |
| Supply Current per Channel | Approximately 1 uA |
| Gain-Bandwidth Product | 5.5 kHz |
| Input Common-Mode Range | Rail-to-rail |
| Output Swing | Rail-to-rail |
| Power-Supply Configuration | Single supply |
| Hộp | 14-pin SOIC (D) |
| Kiểu lắp đặt | Surface mount |
Hướng dẫn cấu hình chân TLV2244ID 14-pin soic (d)
Cấu hình chân cho TLV2244ID (14-pin soic (d) gói). Thành phần số hiệu này có chân đầu vào, đầu ra và nguồn cung cấp. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết cấu hình chân bù, bù trừ và chân kích hoạt. Hoàn hảo cho điều kiện tín hiệu và mạch khuếch đại.
Không có dữ liệu chân cụ thể sẵn có cho TLV2244ID.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
TLV2244ID phù hợp cho 6 Áp dụngs: Battery-Powered Sensor Conditioning, Portable Medical Monitoring, Industrial Process Measurement, Low-Power Active Filtering, IoT Sensor Interface, Precision Control Loop.
Battery-Powered Sensor Conditioning
The TLV2244ID fits low-power sensor interfaces because four channels are available at approximately 1 uA supply current per channel. Each amplifier can condition a low-frequency sensor output while operating from a 2.5 V to 12 V source. Rail-to-rail input and output operation helps use the available signal range in compact battery-powered instruments. The 5.5 kHz gain-bandwidth product is suitable for slow sensor signals, but the final gain must preserve closed-loop stability and reject out-of-band noise.
Được đề xuất
Portable Medical Monitoring
The TLV2244ID is appropriate for multichannel, low-frequency medical monitoring when the system emphasizes low power and compactness. Four rail-to-rail amplifier channels can process buffered sensor or electrode-related signals from one 14-pin SOIC package. The approximately 1 uA per-channel supply current helps limit the amplifier's contribution to overall portable-system power. Because medical designs may require specific accuracy, noise, isolation, and qualification controls, engineers must verify those limits against the manufacturer datasheet and applicable product requirements before use.
Được đề xuất
Industrial Process Measurement
The TLV2244ID can support low-bandwidth process measurement circuits that require several conditioned inputs but operate from limited power budgets. Its four amplifier channels reduce PCB area in transmitter, controller, and data-acquisition modules, while the 2.5 V to 12 V range permits use with low-voltage industrial rails. The 5.5 kHz gain-bandwidth product suits slow pressure, temperature, and level signals rather than fast transient waveforms. Input filtering and isolation requirements should be designed separately for each industrial measurement channel.
Được đề xuất
Low-Power Active Filtering
The TLV2244ID is suitable for low-frequency active filters where four amplifier channels can implement repeated first or second-order stages. The 5.5 kHz gain-bandwidth product provides useful bandwidth for slow control, audio-adjacent, or instrumentation signals, while approximately 1 uA per channel favors portable equipment. Component tolerances and the amplifier's frequency-response limits must be included in filter-error analysis. Confirm closed-loop stability for each gain setting and the intended loading before releasing the filter design.
Được đề xuất
IoT Sensor Interface
The TLV2244ID can condition several low-speed inputs in an IoT sensor node while preserving system energy budget. Its four rail-to-rail channels are useful for resistive dividers, current-sense outputs, and analog sensor signals operating from a 2.5 V to 12 V rail. The low approximately 1 uA per-channel supply current is beneficial when the node spends long periods in a low-power state. Choose resistor values, filtering, and shutdown architecture around the sensor's bandwidth and the node's required measurement accuracy.
Được đề xuất
Precision Control Loop
The TLV2244ID is appropriate for slow feedback-control and set-point conditioning functions requiring more than one amplifier channel. Its low supply current benefits distributed or battery-powered control hardware, and rail-to-rail output behavior supports signal swings near the available supply range. The modest 5.5 kHz gain-bandwidth product suits control loops with bandwidth well below that value. Validate loop stability, offset contribution, startup behavior, and the effects of output loading in the complete analog system.
Được đề xuất
Dữ liệu tham khảo kỹ thuật cho TLV2244ID — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này |
|---|---|
| Brand | Texas Instruments |
| Package | 14-pin SOIC (D) |
| Number of Channels | 4 channels |
| Supply Voltage Range | 2.5 V to 12 V |
| Supply Current per Channel | Approximately 1 uA |
| Gain-Bandwidth Product | 5.5 kHz |
| Input Common-Mode Range | Rail-to-rail |
| Output Swing | Rail-to-rail |
Bảo phân biệt quan trọng
- Four amplifier channels in one package (vsSingle-channel TLV2241-family device)
- Micropower operation for portable systems (vsTypical general-purpose 14-pin SOIC operational amplifier)
- Rail-to-rail input and output operation (vsNon-rail-to-rail low-power operational amplifier)
Ghi chú thiết kế
Route each input and feedback connection directly to its associated amplifier pin, and place any biasing or compensation network close to the relevant input. Keep the feedback loop compact because the 5.5 kHz gain-bandwidth product limits high-frequency loop shaping. Connect the supply and ground pins with short paths and use a local bypass capacitor where the board design requires additional high-frequency decoupling.
Verify stability with the actual signal-source impedance, gain, load, and output capacitance. A rail-to-rail amplifier can approach its supply rails through different internal paths, so input and output common-mode ranges must be checked independently at the operating supply voltage. For low-frequency precision signals, evaluate offset, bias current, and drift against the required error budget rather than relying only on gain-bandwidth product.
Estimated total amplifier supply current is approximately 4 uA when all four channels operate at the typical 1 uA per-channel current. This estimate uses the manufacturer's approximately 1 uA per-channel value and does not include external resistor currents, sensor loads, regulator losses, or leakage. Compare the complete circuit's average and peak current against the available supply, especially in battery-operated designs.
Do not treat the low gain-bandwidth product as suitable for high-speed signal amplification, and do not assume every rail-to-rail amplifier has identical input and output limits. Use the manufacturer pin-description table when assigning the 14-pin SOIC connections, and use the ordering-information table to confirm that the mechanical package matches the PCB footprint. Validate unused channels according to the recommended configuration in the datasheet.
Thông tin tuân thủ
The available product information does not state RoHS, REACH, lead-free, halogen-free, or conflict-minerals status. AEC-Q100 qualification is not indicated for this ordering code.