TPA3007D1PW - 6.5W Mono Class-D Amplifier | Texas Instruments
MPN: TPA3007D1PW ✓ Hoạt độngTPA3007D1PW Tóm tắt
A Class-D audio amplifier is a power-management IC that switches its output stage between active states instead of continuously dissipating a signal through a linear output transistor. The Class-D hierarchy—audio amplifier, power amplifier, amplifier IC, and semiconductor—places the TPA3007D1PW in portable and embedded audio systems where speaker output, supply efficiency, compactness, and analog-input compatibility are important.
The TPA3007D1 family provides a 6.5 W output rating, 8 V to 18 V analog supply operation, and a 36 dB gain setting. Its filter-free operation simplifies the signal path, while the 20 kHz specification corresponds to the audio bandwidth identified in the product documentation. The 24-pin TSSOP package allows a compact implementation but requires careful attention to thermal performance because acoustic output and switching losses are concentrated in a small package.
The amplifier uses a bridge-tied-load architecture, allowing the differential speaker outputs to develop the required voltage swing without a speaker-coupling capacitor. The manufacturer's documentation notes that an 8 Ω speaker can be driven with a ferrite-bead filter to reduce electromagnetic interference. Input and output filtering, supply bypassing, and return-current management remain essential even though the amplifier is described as filter-free.
Typical uses include compact Bluetooth speakers, portable audio products, sound-bar transducers, industrial annunciators, consumer audio modules, and other systems powered by an 8 V to 18 V source. The mono architecture suits a single-speaker enclosure, while the analog input allows connection to a DAC, audio codec, or another analog sound source.
For layouts, place the input, supply, and output filtering components close to their associated pins and maintain a compact power-loop area. Treat the exposed package area as a thermal and current path, provide adequate PCB copper, and verify speaker-load power and temperature rise in the final enclosure. The 8 V minimum supply requirement also makes this device less suitable than lower-voltage Class-D amplifiers for designs powered directly by a single-cell lithium battery.
This page combines the manufacturer's device specifications with application guidance, sourcing information, and an engineering comparison of orderable alternatives. The comparison focuses on package compatibility, electrical ratings, and the practical differences that matter when replacing or evaluating mono Class-D amplifier implementations.
Bộ thay thế dễ dàng lắp đặt cho TPA3007D1PW — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
TPA3007D1PWR
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
TPA3007D1PWG4
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
TPA3007D1PWRG4
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
TPA3007D1PW Tỷ lệ tối đa & tính chất điện
| Product Type | Mono Class-D audio power amplifier |
| Maximum Output Power | 6.5 W |
| Supply Voltage Range | 8 V to 18 V |
| Input Type | Analog input |
| Number of Audio Channels | 1 channel |
| Output Architecture | Bridge-tied load (BTL) |
| Gain | 36 dB |
| Frequency | 20 kHz |
| Minimum Speaker Load | 8 ohm |
| Hộp | 24-pin TSSOP (PW) |
| Package Width | 4.40 mm |
| Khoảng nhiệt độ hoạt động | -40 °C to 85 °C |
| Kiểu lắp đặt | Surface mount |
| EMI Control | Ferrite-bead filter recommended for the 8 ohm speaker output |
| Output Coupling | No speaker-coupling capacitor required for the bridge-tied-load output |
Hướng dẫn cấu hình chân TPA3007D1PW 4.40 mm
Cấu hình chân cho TPA3007D1PW (4.40 mm gói). Thành phần số hiệu này có chân đầu vào, đầu ra và nguồn cung cấp. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết cấu hình chân bù, bù trừ và chân kích hoạt. Hoàn hảo cho điều kiện tín hiệu và mạch khuếch đại.
Không có dữ liệu chân cụ thể sẵn có cho TPA3007D1PW.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
TPA3007D1PW phù hợp cho 6 Áp dụngs: Portable Bluetooth Speaker, Compact Sound-Bar Speaker, Industrial Audible Alarm, Consumer Audio Module, Personal Audio Accessory, Test and Measurement Audio Fixture.
Portable Bluetooth Speaker
The TPA3007D1PW fits a compact powered speaker that uses an 8 V to 18 V internal rail and requires more output than a low-power integrated audio amplifier can provide. Its 6.5 W mono Class-D stage drives an 8 Ω speaker through a bridge-tied-load arrangement without a series output capacitor. The 24-pin TSSOP package also conserves board area compared with a larger power package. Design the power path around the 18 V maximum supply, provide local supply bypassing, and verify the speaker impedance under every operating condition. A ferrite-bead filter can be added to the speaker outputs if system-level testing reveals unacceptable electromagnetic interference.
Được đề xuất
Compact Sound-Bar Speaker
The TPA3007D1PW is appropriate for a single-driver sound-bar module that receives analog audio from a codec or DAC and operates from an 8 V to 18 V power system. Its 6.5 W rating provides useful output for compact furniture while the Class-D topology limits dissipation compared with a linear amplifier. The bridge-tied-load outputs should be routed as a compact differential pair, and output filtering should be evaluated after the speaker cable and enclosure are installed. Keep analog input routing away from the switching outputs, and confirm that the shutdown and mode-control pins match the product-system requirements.
Được đề xuất
Industrial Audible Alarm
The TPA3007D1PW can drive an 8 Ω industrial alarm transducer from an 8 V to 18 V industrial audio rail while maintaining a compact amplifier footprint. The 6.5 W mono rating is useful where an audible notification must overcome enclosure losses, and the -40 °C to 85 °C operating range supports temperature-controlled equipment. Because Class-D output edges can interfere with sensitive analog or control circuitry, reserve continuous copper around the amplifier, keep switching-current paths compact, and validate emissions. The design must also include protection appropriate to the transducer and wiring environment.
Được đề xuất
Consumer Audio Module
The TPA3007D1PW suits a consumer module requiring a single high-efficiency speaker channel from an analog source. Its 6.5 W output, 36 dB gain, and 20 kHz bandwidth specification align with conventional full-range audio use, while the 24-pin TSSOP package supports compact board layouts. Place input-network components close to their pins, maintain a low-impedance ground return, and decouple the analog supply locally. Confirm the amplifier's mode and shutdown behavior in the system control logic, and conduct thermal testing at the maximum expected music or alarm output level rather than relying only on nominal signal conditions.
Được đề xuất
Personal Audio Accessory
The TPA3007D1PW can serve as the speaker amplifier in a portable personal-audio accessory that includes a boost stage and operates at 8 V to 18 V. Compared with a 5 V-class amplifier, the device can deliver a 6.5 W mono output with a higher available supply, while its Class-D operation improves conversion efficiency. The accessory designer must account for boost-converter startup, speaker transients, and enclosure heat dissipation. Use a common or carefully isolated analog and power ground strategy, route the two speaker outputs as a matched pair, and verify operation across battery range and accessory-cable length.
Được đề xuất
Test and Measurement Audio Fixture
The TPA3007D1PW is usable in a compact audio test fixture that converts an analog source into a 6.5 W bridge-tied-load speaker drive. Its 8 V to 18 V supply range and 36 dB gain provide useful control for evaluating transducers without a large linear amplifier. A precision DAC can generate test signals, while short speaker wiring helps limit EMI and transmission-line effects. Add output filtering if required by the test specification, check channel polarity before measurements, and verify that the instrument enclosure can dissipate the worst-case output condition. The amplifier is a power stage and should not replace calibrated measurement front ends.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho TPA3007D1PW — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | TPA3007D1PWR | TPA3007D1PWG4 | TPA3007D1PWRG4 |
|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 24-pin TSSOP (PW) | 24-pin TSSOP (PW) | 24-pin TSSOP (PW) | 24-pin TSSOP (PW) |
| Output Power | 6.5 W | 6.5 W | 6.5 W | 6.5 W |
| Supply Voltage Range | 8 V to 18 V | 8 V to 18 V | 8 V to 18 V | 8 V to 18 V |
| Channel Configuration | Mono | Mono | Mono | Mono |
| Amplifier Class | Class D | Class D | Class D | Class D |
| Input Type | Analog input | Analog input | Analog input | Analog input |
| Gain | 36 dB | 36 dB | 36 dB | 36 dB |
| Frequency | 20 kHz | 20 kHz | 20 kHz | 20 kHz |
| Output Architecture | Bridge-tied load (BTL) | Bridge-tied load (BTL) | Bridge-tied load (BTL) | Bridge-tied load (BTL) |
| Operating Temperature Range | -40 °C to 85 °C | -40 °C to 85 °C | -40 °C to 85 °C | -40 °C to 85 °C |
Bảo phân biệt quan trọng
- Matches the documented TPA3007D1 electrical configuration (vsTPA3007D1PWR)
- Preserves the same board footprint and power architecture (vsTPA3007D1PWG4)
- No functional performance penalty in the documented R/G4 ordering option (vsTPA3007D1PWRG4)
Ghi chú thiết kế
Route the two bridge-tied-load outputs as a compact, closely coupled pair and keep them away from the analog input and precision reference circuitry. Place output ferrite beads at the amplifier side of the speaker connector so unwanted switching harmonics are attenuated before entering long speaker wiring. Provide continuous ground and supply planes under the device, and route high-current return currents directly to the supply-decoupling capacitor rather than through analog signal ground paths.
The 8 V to 18 V supply range is a hard design boundary. Use local decoupling at the power pins and confirm the amplifier start-up and operating current against the selected supply. Do not substitute a lower-voltage rail without recalculating the output voltage swing and power capability. Protect the 18 V maximum from transient overshoot and verify the shutdown behavior during power sequencing.
The 24-pin TSSOP package has limited thermal mass even though Class-D operation reduces continuous dissipation. Estimate worst-case conductor loss and switching loss using the maximum supply, load impedance, output power, and amplifier efficiency. Then verify junction-temperature margin on the intended PCB with the enclosure installed. Use uninterrupted copper beneath and around the exposed package area, but follow the manufacturer land-pattern requirements for that PW option.
Class-D output edges can create radiated emissions even when the amplifier is described as filter-free. Evaluate the complete speaker, cable, power supply, and enclosure because changing any one of them can alter EMI performance. Start with short, symmetric output routing and add ferrite-bead filtering when measurements show it is necessary. Conduct both radiated and conducted emissions testing before releasing the product.
Do not assume that a speaker with a nominal 8 Ω rating presents a constant 8 Ω load. Voice-coil impedance varies with frequency and may dip below its rated value, increasing current and risk of distortion or protection action. Verify the transducer specification, maintain speaker wiring polarity, and test with the intended amplifier-to-speaker cable. Also avoid grounding only one side of the bridge-tied output, because both output terminals carry switching activity.
Thông tin tuân thủ
Compliance details were not stated in the cited manufacturer product-page, product-detail, or distributor excerpts. The TPA3007D1PWG4 ordering designation is present in the alternative-part information, but it is not treated as sufficient evidence for a product-wide RoHS or halogen-free declaration.