TPS54283 - Dual 2A 300kHz Buck Converter | Texas Instruments
MPN: TPS54283 ✓ Hoạt độngTPS54283 Tóm tắt
What is a non-synchronous buck converter? A non-synchronous buck converter is a step-down switching regulator that uses an integrated high-side MOSFET as the control switch and an external Schottky diode as the low-side rectifier. Because the TPS54283 integrates the high-side switch, each of its two channels only needs an external Schottky diode, an inductor, and input/output capacitors. In the power management hierarchy it is: DC-DC converter -> non-synchronous buck converter -> step-down switching voltage regulator -> power management IC.
Key features include dual 2-A outputs, a wide 4.5-V to 28-V input range, adjustable output down to 0.8 V, fixed 300-kHz switching, internal compensation, and an integrated high-side MOSFET. The internal error-amplifier compensation removes the external compensation network, reducing BOM count and simplifying loop-stability design. The wide input range gives margin for 5-V, 12-V, and 24-V systems.
From a technical standpoint, the current-mode controlled converter balances inductor size, output ripple, and efficiency at 300 kHz. Because the low-side rectifier is external, a designer can optimize the Schottky diode for forward voltage and thermal behavior. The PowerPAD must be soldered to a solid ground-plane copper area to keep junction temperature within limits at full dual 2-A load.
Typical applications include broadband gateways (DSL/cable modems), IP security cameras, set-top boxes, and industrial control boards that generate a 5-V and a 3.3-V rail from a 12-V or 24-V input. The adjustable output also supports point-of-load power in consumer media devices.
When designing with the TPS54283, verify input-to-output headroom and Schottky diode rating for each channel, and use the exposed thermal pad to a large ground copper pour. Total dissipation is the combined loss of both channels, so thermal layout is critical at 2 A per output.
Bộ thay thế dễ dàng lắp đặt cho TPS54283 — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
TPS54286PWP
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
TPS54183PWP
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
TPS54383PWP
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
TPS54386PWP
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
TPS54283 Tỷ lệ tối đa & tính chất điện
| Chức năng | Dual non-synchronous buck converter |
| Số lượng đầu ra | 2 |
| Phạm vi điện áp đầu vào | 4.5 V to 28 V |
| Output Current per Channel | 2 A |
| Khoảng điện áp đầu ra | 0.8 V to 90% of VIN |
| Tần số chuyển đổi | 300 kHz (fixed) |
| Kiểu đầu ra | Adjustable |
| Integrated High-Side MOSFET | Yes |
| Low-Side Rectifier | External Schottky diode |
| Compensation | Internal |
| Hộp / Vỏ | 14-PowerTSSOP (HTSSOP-14, PWP) 4.40 mm width |
| Kiểu lắp đặt | Surface Mount |
| Thermal Pad | Exposed PowerPAD |
| RoHS | unknown (not provided in verified data) |
Hướng dẫn cấu hình chân TPS54283 14-powertssop (htssop-14, pwp) 4.40 mm width
Cấu hình chân cho TPS54283 (14-powertssop (htssop-14, pwp) 4.40 mm width gói). Động cơ điện này có chân cổng, nguồn và đầu ra. Đối với các gói không phân極, tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết hướng dẫn chính xác của chân 1 và chi tiết về vân footprint. Các ứng dụng phổ biến bao gồm thiết kế nguồn cung cấp điện, điều khiển động cơ và chuyển đổi tải.
Không có dữ liệu chân cụ thể sẵn có cho TPS54283.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
TPS54283 phù hợp cho 6 Áp dụngs: Industrial Dual-Rail Power Supply, Broadband Gateway / DSL Modem Power, IP Security Camera Main Board, Set-Top Box / Media Player Power, 12-V Battery-Powered Industrial Equipment, Telecom / Networking Line Card.
Industrial Dual-Rail Power Supply
The TPS54283 is a natural fit for industrial dual-rail power supplies that convert a 24-V or 12-V bus into 5-V and 3.3-V logic rails. With a 4.5-V to 28-V input, each 2-A channel can drive MCU, FPGA, and sensor loads, while the integrated high-side MOSFET and internal compensation minimize external parts. One consideration is thermal: a 24-V to 5-V conversion at 2 A has large VIN-VOUT delta, so use a high-current Schottky diode and a large PowerPAD copper area to keep junction temperature within limits.
Được đề xuất
Broadband Gateway / DSL Modem Power
Broadband gateways need multiple clean rails from a 12-V wall adapter. The TPS54283's two 2-A channels can generate 3.3 V for the SoC and 5 V for PHY or USB peripherals. The fixed 300-kHz switching reduces EMI in unshielded plastic enclosures, and internal compensation simplifies the BOM. At 2 A per channel, place the converter near the input connector and keep output traces short to minimize ripple; overall system thermal load should also factor in the adjacent Ethernet PHY and memory components.
Được đề xuất
IP Security Camera Main Board
IP cameras powered over PoE use 48-V or 24-V to feed an intermediate 12-V rail, and the TPS54283 can then generate sensor-core and I/O rails. Its 2 A per channel covers CMOS image sensor, ISP, motor, and IR-LED auxiliary loads, while the 300-kHz switching keeps inductor size small for tight PCB form factors. Use the exposed PowerPAD to a ground pour and select a Schottky diode rated above the peak inductor current; the adjustable output also allows fine voltage trimming.
Được đề xuất
Set-Top Box / Media Player Power
In set-top boxes and media players, the TPS54283 produces 5 V and 3.3 V from a 12-V adapter. Two 2-A channels are sufficient for the main SoC, DDR memory, Wi-Fi module, and front-end tuner. Internal compensation and integrated high-side MOSFET reduce BOM count and layout risk, and the dual outputs replace two single-channel bucks. Keep the switching node area small and the BOOT capacitor close to the IC; total board dissipation should be reviewed for fanless enclosures at full 2-A load.
Được đề xuất
12-V Battery-Powered Industrial Equipment
For battery-powered industrial equipment, the TPS54283 accepts a 12-V nominal battery with input variation from 9 V to 16 V within its 4.5-V to 28-V range. Two 2-A outputs can power a host controller and actuators or I/O. At lower battery voltages the fixed 300-kHz converter still keeps high efficiency; at 4.5-V minimum input, output voltage can still be programmed down to 0.8 V. Use low-ESR ceramic caps and a Schottky diode sized for the maximum inductor ripple current.
Được đề xuất
Telecom / Networking Line Card
On telecom line cards, board space is valuable and multiple rails are needed. The TPS54283's dual 2-A outputs generate 3.3 V and 1.8 V or 2.5 V from an intermediate 12-V bus, and the integrated high-side MOSFET keeps switching cells compact. The 300-kHz frequency stabilizes EMI across the card, and internal compensation reduces tuning effort. For higher-current rails, a companion TPS54383PWP (3 A) can be used, keeping the same HTSSOP-14 footprint.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho TPS54283 — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | TPS54286PWP | TPS54183PWP | TPS54383PWP | TPS54386PWP |
|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 14-PowerTSSOP (HTSSOP-14, PWP) | 14-PowerTSSOP - same | 14-PowerTSSOP - same | 14-PowerTSSOP - same | 14-PowerTSSOP - same |
| Output Current per Channel | 2 A | 2 A | 1 A | 3 A | 3 A |
| Switching Frequency | 300 kHz | 600 kHz | 300 kHz | 300 kHz | 600 kHz |
| Input Voltage Range | 4.5 V to 28 V | 4.5 V to 28 V | 4.5 V to 28 V | 4.5 V to 28 V | 4.5 V to 28 V |
| Output Voltage Range | 0.8 V to 90% of VIN | 0.8 V to 90% of VIN | 0.8 V to 90% of VIN | 0.8 V to 90% of VIN | 0.8 V to 90% of VIN |
| Number of Outputs | 2 | 2 | 2 | 2 | 2 |
| Compensation | Internal | Internal | Internal | Internal | Internal |
Bảo phân biệt quan trọng
- Dual 2-A output capability in one 14-pin package (vsTPS54183PWP)
- Fixed 300-kHz switching with internal compensation (vsTPS54286PWP)
- Cost-optimized for 2-A dual-rail loads (vsTPS54383PWP)
Ghi chú thiết kế
The TPS54283 is supplied in a 14-pin PowerTSSOP with exposed PowerPAD. At 12-V input, 3.3-V/2-A output per channel, total loss can exceed 4 W. Solder the PowerPAD to a large ground-plane copper area (at least 1 in² per channel equivalent) and add thermal vias under the pad to reduce theta_JA. Without proper thermal design, junction temperature may exceed the recommended limit at high ambient.
Place a 10-uF ceramic input capacitor near the VIN pins and a 0.1-uF BOOT capacitor close to BOOT/SW for the high-side gate drive. Use a Schottky diode rated for at least 3 A and low forward voltage, with the diode cathode close to the SW pin and anode to GND. Keep the SW node compact and away from the feedback/sense traces to reduce noise coupling.
Do not exceed 28 V on VIN, and remember the maximum output voltage is 90% of VIN, not rail-to-rail. The outputs are adjustable with an external resistor divider; use 1% resistors. Because the converter is non-synchronous, omitting the external Schottky diode will cause high dissipation and possible damage. Always verify component ratings at the actual peak inductor current.
Thông tin tuân thủ
Verified web data did not include compliance certificates; confirm with TI product page before claiming compliance.
