TS3V330D - 4-Channel SPDT Video Switch | Texas Instruments
MPN: TS3V330D ✓ Hoạt độngTS3V330D Tóm tắt
A video switch is an analog multiplexer or demultiplexer that routes one of two signal paths to a common output. The SPDT configuration supports source selection, signal swapping, and isolation between alternate inputs. In the system hierarchy, the TS3V330D belongs to the analog switch family, which falls under interface ICs and broader semiconductor signal-routing devices. Four integrated channels reduce component count when several video lines must be switched together.
The principal features of the TS3V330D include four independent 2:1 switch channels, a common single switch-enable input, a 3.3 V supply requirement, wide-bandwidth video switching, and low on-state resistance. The 16-SOIC package supports conventional surface-mount assembly. These characteristics make the device relevant to video test equipment, multimedia routing, projection systems, display processing, and industrial imaging designs where multiple source paths must be selected electronically.
The TS3V330D uses a single enable-control architecture rather than four separate control inputs. This simplifies command-line interfacing when all four channels must change state together. Its wide-bandwidth design is intended to preserve video signals while keeping conduction loss relatively low. Because a video switch is an analog device, signal integrity depends not only on on-state resistance but also on off-state isolation, channel matching, board-level parasitics, and the impedance of the source and destination circuitry.
Typical implementations include selecting between composite or component video inputs, routing test signals into an oscilloscope or video analyzer, switching cameras within surveillance equipment, and controlling auxiliary video paths in projection or display equipment. The common enable input also supports systems that need to mute or disconnect several video lines together. Firmware-controlled source selection is particularly practical when the same board must support several external connectors.
PCB layout should keep video traces short, provide a continuous ground reference, and place bypass capacitance close to the supply pin. Designers should verify the complete channel bandwidth, isolation, insertion loss, and crosstalk against the source impedance and cable length. The common enable signal should be controlled only after the selected input is stable, preventing transient switching artifacts from reaching downstream video circuitry.
This product page combines the device identity, package information, operating limits, confirmed cross-reference options, and practical design guidance for engineers evaluating the TS3V330D. It also distinguishes the core four-channel SPDT switching function from broader interface and signal-routing categories, making the component easier to compare with suitable video-switching designs.
Bộ thay thế dễ dàng lắp đặt cho TS3V330D — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
TS3V330DR
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
TS3V330DE4
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
TS3V330DRE4
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
TS3V330D Tỷ lệ tối đa & tính chất điện
| Product Type | 4-channel 2:1 SPDT video switch |
| Number of Channels | 4 channels |
| Switch Configuration | 2:1 SPDT |
| Điện áp cung cấp | 3.3 V |
| Hộp | 16-pin SOIC |
| Số chân | 16 pins |
| Khoảng nhiệt độ hoạt động | -40°C to +85°C |
| Switch Enable Inputs | 1 common switch-enable input |
| Kiểu lắp đặt | Surface mount |
Hướng dẫn cấu hình chân TS3V330D 16-pin soic
Cấu hình chân cho TS3V330D (16-pin soic gói). Số thứ tự chân, chức năng và sơ đồ kết nối được xác định trong tài liệu thông số kỹ thuật của nhà sản xuất. Tham khảo nó để biết footprint và hướng dẫn hàn chính xác.
Không có dữ liệu chân cụ thể sẵn có cho TS3V330D.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
TS3V330D phù hợp cho 6 Áp dụngs: Video Source Selection, Video Test and Measurement, Industrial Inspection Systems, Surveillance Camera Routing, Display and Projection Equipment, Multimedia and Connectivity.
Video Source Selection
The TS3V330D is well suited to selecting between two analog video sources because it combines four 2:1 SPDT channels in one 16-pin SOIC. A receiver can route the selected inputs through the switch using a common enable signal rather than placing four separate single-channel devices on the board. The 3.3 V supply matches many digital video-processing systems, while wide-bandwidth operation and low on-state resistance help preserve the selected signal. This arrangement is useful in test equipment, multimedia inputs, and display systems that must present different sources through a shared downstream channel.
Được đề xuất
Video Test and Measurement
The TS3V330D can route multiple video connections toward a common test path when an instrument needs to choose among several sources. Its four independent SPDT positions provide parallel routing while the common switch-enable input allows coordinated state changes. The 16-SOIC package keeps the implementation compact, and the -40°C to +85°C range supports laboratory and industrial test equipment. Engineers should preserve controlled return paths and verify the complete signal chain because connector launches and cable impedance can influence isolation and crosstalk.
Được đề xuất
Industrial Inspection Systems
The TS3V330D fits industrial inspection equipment that alternates among camera or video-source paths. Four SPDT channels allow several related signals to change selection together, which can simplify synchronization in systems carrying video, sync, or associated control signals. Its 3.3 V operation integrates readily with modern embedded processing, and the -40°C to +85°C range covers many factory environments. The common enable input should be sequenced carefully so that the selected source has settled before downstream circuitry samples or displays the routed signal.
Được đề xuất
Surveillance Camera Routing
The TS3V330D can support routing among multiple surveillance-video inputs in compact camera or monitoring equipment. Its four-channel 2:1 arrangement allows one output path to select between alternative sources without requiring four separate switch packages. The 3.3 V supply and 16-pin SOIC are appropriate for space-conscious electronics, while the wide-bandwidth design targets video signals. Layout should maintain a continuous ground plane, minimize long video loops, and account for protection-network capacitance that could degrade isolation or channel matching.
Được đề xuất
Display and Projection Equipment
The TS3V330D is applicable to display and projection systems that must route one of two video inputs into a shared processing path. Four channels permit coordinated selection of video-related signals, while a single common enable input reduces control complexity. The 16-pin SOIC footprint supports compact board layouts, and the 3.3 V supply integrates with contemporary display controllers. To preserve signal quality, route video lines over continuous ground planes, keep bypass capacitance close to the supply connection, and verify connector and cable behavior across the intended video bandwidth.
Được đề xuất
Multimedia and Connectivity
The TS3V330D can provide compact analog switching in multimedia panels, docking products, and connectivity modules that offer selectable video inputs. Four 2:1 channels reduce the footprint required for multiple route selections, and the common enable input supports coordinated switching through one control signal. The 3.3 V supply is practical for portable and embedded equipment, while the -40°C to +85°C range supports industrial variants. Firmware should avoid changing the route while downstream devices are active if transient artifacts would be visible or misinterpreted.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho TS3V330D — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | TS3V330DR | TS3V330DE4 | TS3V330DRE4 |
|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC |
| Channel Count | 4 channels | 4 channels | 4 channels | 4 channels |
| Switch Configuration | 2:1 SPDT | 2:1 SPDT | 2:1 SPDT | 2:1 SPDT |
| Enable Architecture | Single common switch-enable input | Single common switch-enable input | Single common switch-enable input | Single common switch-enable input |
Bảo phân biệt quan trọng
- Four video channels integrated in one switch (vsTS3V330DR)
- Common control simplifies synchronized routing (vsTS3V330DE4)
- Direct 16-pin SOIC compatibility (vsTS3V330DRE4)
Ghi chú thiết kế
Route the four video channels over a continuous ground plane and keep their traces short and similarly referenced. Avoid crossing long switch-output routes with unrelated high-current or high-speed digital paths. Place the 3.3 V bypass capacitor close to the supply pin and connect its ground return directly to the device ground. The 16-pin SOIC footprint provides limited pin-escape space, so planning the signal order before routing reduces loop area and simplifies impedance-controlled implementation.
Verify insertion loss, off-state isolation, bandwidth, and crosstalk for the complete path rather than treating the switch as an ideal routing element. Connector launches, protection components, source impedance, and cable length can materially affect video performance. Use matched source and load impedances where possible, and preserve the selected channel's reference path. These checks are especially important when the four channels carry related video, sync, or control signals that must remain aligned.
Do not assume that every TS3V330 ordering suffix is interchangeable without checking assembly requirements. TS3V330DR, TS3V330DE4, and TS3V330DRE4 are identified as pin-compatible alternatives, but reel configuration, marking, order quantity, and lifecycle details may differ. Also avoid changing the common enable state while downstream circuitry is sampling, because the transition interval can briefly place both switch paths in an uncertain state and create a visible transient.
Thông tin tuân thủ
The device is an industrial-temperature interface IC, but no specific RoHS, REACH, lead-free, halogen-free, or conflict-minerals declarations were identified in the cited product information. AEC-Q100 is not applicable to the standard TS3V330D ordering designation.