TS942IPT - 10kHz Dual RRO Op Amp | STMicroelectronics
MPN: TS942IPT ✓ Hoạt độngTS942IPT Tóm tắt
An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its two inputs while using negative feedback to establish gain and bandwidth. A rail-to-rail input stage accepts signals close to the positive and negative supply rails, while a rail-to-rail output stage can approach those limits under suitable load conditions. The TS942IPT therefore belongs to the rail-to-rail operational-amplifier family within the broader amplifier and analog IC hierarchy.
Key characteristics include two amplifier circuits in one package, 10 kHz gain-bandwidth product, rail-to-rail operation, and approximately 1.2 µA supply current per channel. Its listed typical output current is 5 mA. These characteristics make it suitable for low-power sensor interfaces, portable instrumentation, and signal-conditioning circuits where device count, board area, and energy use are important constraints.
The TS942IPT uses an 8-TSSOP package measuring approximately 0.173 inch, or 4.40 mm, in width. Tape-and-reel packaging supports high-volume automated assembly. The manufacturer specifies an operating-temperature range of -40 °C to +85 °C. As a general-purpose dual amplifier, it can reduce component count in designs that need two nearly identical signal-conditioning channels.
Typical uses include low-level sensor signal conditioning, battery-powered measurement modules, industrial control interfaces, portable medical instruments, and low-voltage audio or communication front ends. Two independent amplifier sections can handle separate channels in a dual-axis sensor, differential receiver, filter, or gain stage, provided each channel's stability, common-mode range, and output-drive requirements are satisfied.
Designers should verify input and output headroom, capacitive-load behavior, noise performance, and output-current demand against the manufacturer datasheet. Decoupling capacitors should be placed close to the supply pins, and unused amplifier inputs should be biased to a defined common-mode voltage. The low 10 kHz bandwidth favors precision and low-power operation rather than high-speed signal handling.
This page combines the exact TS942IPT package and operating characteristics with application guidance, same-family drop-in alternatives, a parameter comparison, and practical layout considerations. It helps engineers evaluate the amplifier's role in low-power analog designs without confusing it with higher-bandwidth or higher-current rail-to-rail amplifiers.
Bộ thay thế dễ dàng lắp đặt cho TS942IPT — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
TS942IDT
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
TS942ILT
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
TS942IYT
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
TS942IPT Tỷ lệ tối đa & tính chất điện
| Number of Amplifier Circuits | 2 circuits |
| Amplifier Type | General-purpose operational amplifier |
| Input and Output Characteristic | Rail-to-rail |
| Gain-Bandwidth Product | 10 kHz |
| Supply Current per Channel | 1.2 uA typical |
| Total Supply Current | 2.4 uA typical for 2 channels |
| Output Current | 5 mA typical |
| Hộp | 8-TSSOP |
| Package Width | 0.173 inch (4.40 mm) |
| Khoảng nhiệt độ hoạt động | -40 °C to +85 °C |
| Kiểu lắp đặt | Surface mount |
| Shipping Package | Tape and reel |
Hướng dẫn cấu hình chân TS942IPT tape and reel
Cấu hình chân cho TS942IPT (tape and reel gói). Thành phần số hiệu này có chân đầu vào, đầu ra và nguồn cung cấp. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết cấu hình chân bù, bù trừ và chân kích hoạt. Hoàn hảo cho điều kiện tín hiệu và mạch khuếch đại.
Không có dữ liệu chân cụ thể sẵn có cho TS942IPT.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
TS942IPT phù hợp cho 6 Áp dụngs: Battery-Powered Sensor Conditioning, Portable Medical Monitoring, Industrial Control Signal Conditioning, Low-Voltage Communication Interface, Portable Audio Front End, Precision Current and Voltage Measurement.
Battery-Powered Sensor Conditioning
The TS942IPT fits low-energy sensor front ends because each amplifier channel draws approximately 1.2 µA of supply current and supports rail-to-rail signal operation. A typical circuit uses one channel to amplify a transducer output and the second for buffering or filtering before conversion by an ADC. The 10 kHz gain-bandwidth product is suitable for slow sensor signals, while the 8-TSSOP package conserves board area. Designers should verify the sensor output range, amplifier input-offset requirements, and common-mode operating region before fixing the gain.
Được đề xuất
Portable Medical Monitoring
TS942IPT is suitable for compact medical-monitoring modules that amplify low-amplitude sensor signals while emphasizing low power consumption. The two amplifier channels can condition separate inputs from a biopotential or wearable sensor, or one channel can provide gain while the other supplies an active-filter or reference-buffer function. Rail-to-rail operation helps use the available supply range efficiently. The design must still account for offset, noise, isolation requirements, and applicable medical-system qualification processes before clinical deployment.
Được đề xuất
Industrial Control Signal Conditioning
The TS942IPT can condition slow industrial-control signals in compact sensor and actuator modules. Its dual-channel configuration allows independent amplification of two related inputs, such as a sensor measurement and a temperature reference, while the approximately 1.2 µA per-channel supply current supports low-power field equipment. Rail-to-rail inputs and outputs improve utilization of a low-voltage rail. Engineers should confirm common-mode limits, output-current demand, operating temperature, and protection requirements for the factory environment.
Được đề xuất
Low-Voltage Communication Interface
TS942IPT can support receive and transmit-side signal conditioning in low-speed, low-power communication equipment. One channel may amplify a receiver output while the other shapes or buffers a feedback or level-shifting signal. Its 10 kHz gain-bandwidth product favors baseband and control signals rather than high-speed data paths, and the dual TSSOP-8 package reduces component count. Layout should preserve a short return path and place supply bypass capacitance close to the amplifier.
Được đề xuất
Portable Audio Front End
The TS942IPT can serve as a low-level audio preamplifier or buffer in a battery-powered audio module. Rail-to-rail input and output behavior allows the amplifier to operate from a compact supply, and two channels can support stereo or microphone-related signal paths. The 5 mA typical output current and 10 kHz gain-bandwidth product indicate a device intended for modest signal levels and bandwidth. The circuit designer should verify output swing, distortion, noise, and capacitive-load behavior for the selected gain configuration.
Được đề xuất
Precision Current and Voltage Measurement
TS942IPT is appropriate for low-power precision measurement circuits where two amplifier channels can process voltage and current information. Rail-to-rail operation provides flexibility when signals occupy much of the available input range, while the approximately 1.2 µA per-channel supply current limits the amplifier's contribution to total system consumption. The 10 kHz bandwidth is appropriate for many slowly changing measurements. Offset voltage, input bias current, drift, resistor matching, and ADC acquisition timing remain the principal design considerations.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho TS942IPT — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | TS942IDT | TS942ILT | TS942IYT |
|---|---|---|---|---|
| Package | TSSOP-8 | TSSOP-8 | TSSOP-8 | TSSOP-8 |
| Brand | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics |
| Number of Amplifier Circuits | 2 circuits | 2 circuits | 2 circuits | 2 circuits |
| Gain-Bandwidth Product | 10 kHz | 10 kHz | 10 kHz | 10 kHz |
| Input and Output Characteristic | Rail-to-rail | Rail-to-rail | Rail-to-rail | Rail-to-rail |
| Mounting Type | Surface mount | Surface mount | Surface mount | Surface mount |
| Shipping Format | Tape and reel | Tape and reel | Tape and reel | Tape and reel |
Bảo phân biệt quan trọng
- Combines two rail-to-rail amplifier channels in one compact package (vsTS942IDT)
- Low power is suitable for continuously operating compact systems (vsTS942ILT)
- Provides enough bandwidth for low-frequency analog signal conditioning (vsTS942IYT)
Ghi chú thiết kế
Place the supply bypass capacitor directly between the TS942IPT supply and ground pins, with a short ground return and minimal loop area. Because the amplifier supports rail-to-rail operation, component tolerances, input bias current, and output loading can become more important than in a conventional mid-supply signal stage. Route sensitive input and feedback traces away from switching nodes and high-current return paths to reduce coupled noise.
Do not assume that two channels in the same package have identical layouts for every feedback configuration. Each channel requires its own stable compensation network and must meet the output-voltage, input common-mode, and capacitive-load conditions stated by STMicroelectronics. A 10 kHz gain-bandwidth product also means that attempting high closed-loop gain on fast signals can introduce substantial phase shift, so verify stability with the intended source and load impedances.
Estimated power dissipation can be calculated from the actual supply voltage and total channel supply current: P = VIN × IQUIESCENT. Using 3.3 V and the listed 2.4 uA total typical supply current for both channels gives approximately 7.92 uW. This estimate excludes load current and switching losses, but it shows why TS942IPT is suitable for aggressively power-managed systems when its bandwidth and output-current capability meet the signal requirements.
Thông tin tuân thủ
No specific RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals statement appears in the product records. AEC-Q100 is not applicable because this is a general-purpose analog amplifier rather than an automotive-qualified device.