TUSB1146RNQT - 10Gbps USB-C Alt Mode Redriver | TI
MPN: TUSB1146RNQT ✓ Hoạt độngTUSB1146RNQT Tóm tắt
A USB Type-C Alt Mode redriver is an interface IC that conditions high-speed differential signals between a USB Type-C controller and a connector or peripheral. It supports loss compensation for USB, DisplayPort, and other protocol-agnostic Alt Mode lanes. The TUSB1146 occupies the redriver, multiplexing, and signal-conditioning stages of a USB Type-C power and data interface.
The TUSB1146 supports USB 3.2 SuperSpeed signals at up to 10 Gbps and VESA DisplayPort 2.0 at up to 10 Gbps, or UHBR10. It supports USB 3.2 x1 Gen 1 and Gen 2, USB 3.2 SSP, two DisplayPort lanes, and four DisplayPort lanes. Its protocol-agnostic architecture also permits use with other USB Type-C Alt Mode interfaces, including HDMI Alt Mode.
The TUSB1146 provides adaptive equalization to compensate for channel loss encountered through PCB traces, connectors, and cables. Its crosspoint-switch architecture supports configurable lane routing for USB and DisplayPort Alt Mode. The manufacturer identifies support for DisplayPort D_DFP pin assignments C, D, and E, making it suitable for systems that require multiple high-speed lane arrangements in a compact host interface.
Typical uses include USB-C docking stations, multi-display adapters, notebook and tablet systems, desktop hosts, video-over-USB-C equipment, and industrial data-acquisition systems. The device is particularly relevant where cable or PCB losses could compromise 10 Gbps signal integrity but the host and connector placement cannot be shortened enough to eliminate the loss.
When laying out a design, preserve the high-speed signal paths as short and symmetric as possible, provide the reference-plane and return-path structures required by the manufacturer recommendations, and place bypass capacitance close to the supply pins. Differential pair geometry and connector launch transitions are especially important at 10 Gbps because the redriver compensates for loss but cannot remove reflections caused by an inconsistent PCB structure.
This page combines the TUSB1146RNQT protocol and package details, application guidance, sourcing information, and a strict assessment of available drop-in replacements. It is intended to help engineers confirm protocol coverage, mechanical fit, thermal expectations, and signal-integrity requirements before integrating the redriver into a USB Type-C Alt Mode design.
Bộ thay thế dễ dàng lắp đặt cho TUSB1146RNQT — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Không có bộ thay thế dễ dàng lắp đặt sẵn có cho sản phẩm này.
Yêu cầu các bộ thay thếTUSB1146RNQT Thông số kỹ thuật
| Device Type | USB Type-C Alt Mode redriver and crosspoint switch |
| Maximum USB Data Rate | 10 Gbps |
| Maximum DisplayPort Data Rate | 10 Gbps |
| DisplayPort Generation | DisplayPort 2.0 UHBR10 |
| USB Protocol Support | USB 3.2 x1 Gen 1 and Gen 2 |
| USB SSP Support | Yes |
| DisplayPort Lane Support | 2 or 4 DisplayPort lanes |
| Supported D_DFP Pin Assignments | Configurations C, D, and E |
| Signal Equalization | Adaptive equalization |
| Architecture | Protocol-agnostic linear redriver |
| Target Port Orientation | Downstream-facing host port |
| Package Type | 40-pin WQFN (RNQ) |
| Package Dimensions | 6 mm x 4 mm |
| Khoảng nhiệt độ hoạt động | 0 C to 70 C |
| Kiểu lắp đặt | Surface mount |
Hướng dẫn cấu hình chân TUSB1146RNQT 6 mm x 4 mm
Cấu hình chân cho TUSB1146RNQT (6 mm x 4 mm gói). Số thứ tự chân, chức năng và sơ đồ kết nối được xác định trong tài liệu thông số kỹ thuật của nhà sản xuất. Tham khảo nó để biết footprint và hướng dẫn hàn chính xác.
Không có dữ liệu chân cụ thể sẵn có cho TUSB1146RNQT.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
TUSB1146RNQT phù hợp cho 6 Áp dụngs: USB-C Docking Station, DisplayPort-over-USB-C Adapter, Notebook USB-C Port, Industrial Data-Acquisition System, Multi-Display USB-C System, Video Capture and Test Equipment.
USB-C Docking Station
The TUSB1146RNQT fits a docking station that must preserve 10 Gbps USB and DisplayPort 2.0 UHBR10 links through connector and cable paths. Its adaptive equalization can recover high-frequency signal margin that would otherwise be lost through the downstream-facing host connection, while the crosspoint architecture supports USB 3.2 SSP and two- or four-lane DisplayPort arrangements. Place the device near the high-speed connector or controlled interconnect boundary and maintain the reference layout recommended by the manufacturer.
Được đề xuất
DisplayPort-over-USB-C Adapter
The TUSB1146RNQT supports DisplayPort 2.0 Alt Mode at up to 10 Gbps, including UHBR10 operation and four-lane configurations. Adaptive equalization helps offset loss through an adapter PCB and external display cable, while the protocol-agnostic crosspoint can route supported DisplayPort lanes without relying on a protocol-specific multiplexer. Designers should still use short, impedance-controlled differential routes and verify the D_DFP C, D, and E assignments required by the target host.
Được đề xuất
Notebook USB-C Port
A notebook or tablet can use the TUSB1146RNQT to condition 10 Gbps signals between its USB Type-C controller and a connector positioned beyond a long internal trace. The device supports USB 3.2 Gen 2 and DisplayPort 2.0, allowing one host-side interface architecture to cover multiple high-speed Alt Mode use cases. Thermal and layout planning should account for the 40-pin WQFN package, while equalization settings and lane routing should follow the manufacturer configuration procedure.
Được đề xuất
Industrial Data-Acquisition System
The TUSB1146RNQT is suitable for industrial acquisition equipment that connects a USB-C interface to sensors, storage, or test circuitry over a long board-level or cable path. Adaptive equalization can improve 10 Gbps signal margin across the lossy interconnect, and the protocol-agnostic design allows support for USB 3.2 SSP and DisplayPort Alt Mode links. Industrial designs should maintain continuous ground references, avoid discontinuities in the return path, and validate operation across the specified 0 C to 70 C temperature range.
Được đề xuất
Multi-Display USB-C System
The TUSB1146RNQT can serve a USB-C system that must switch among USB and DisplayPort Alt Mode functions while supporting two or four DisplayPort lanes. Its crosspoint-switch capability provides a configurable path for protocol-agnostic high-speed signals, and adaptive equalization helps maintain link margin across connector and PCB losses. The implementation should verify every supported D_DFP configuration, C, D, or E, and use the manufacturer lane-routing and equalization procedure during hardware bring-up.
Được đề xuất
Video Capture and Test Equipment
The TUSB1146RNQT can condition a 10 Gbps USB 3.2 or DisplayPort 2.0 link in video capture, analysis, and signal-integrity test equipment. Adaptive equalization offers a way to recover signal margin across long internal traces, cable interfaces, and repeated connector transitions. Because the device is a linear redriver rather than a protocol converter, the surrounding system must configure the source, sink, lane routing, and Alt Mode negotiation correctly, followed by signal-integrity validation at the intended data rate.
Được đề xuất
Dữ liệu tham khảo kỹ thuật cho TUSB1146RNQT — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này |
|---|---|
| Brand | Texas Instruments |
| Package | 40-pin WQFN (RNQ), 6 mm x 4 mm |
| Maximum USB Data Rate | 10 Gbps |
| Maximum DisplayPort Data Rate | 10 Gbps |
| DisplayPort Support | DisplayPort 2.0 UHBR10 |
| USB 3.2 Support | x1 Gen 1 and Gen 2 with SSP support |
| DisplayPort Lane Support | 2 or 4 lanes |
| Equalization | Adaptive equalization |
| D_DFP Support | Configurations C, D, and E |
| Operating Temperature | 0 C to 70 C |
Bảo phân biệt quan trọng
- Combines USB and DisplayPort high-speed redriving in one host-side device (vsGeneric protocol-specific USB redrivers)
- Supports advanced DisplayPort operation (vsDisplayPort 1.4-oriented redrivers)
- Adapts to channel loss instead of relying only on fixed compensation (vsFixed-equalization redrivers)
- Configurable high-speed lane routing (vsSingle-purpose signal conditioners)
Ghi chú thiết kế
Route all 10 Gbps lanes as short, continuous, impedance-controlled differential pairs. Avoid changing layer references, adding unmatched stubs, and placing test pads directly in the high-speed path unless the component and board design support them. Keep the redriver close to the physical loss boundary when the far side contains a long PCB path or connector transition. Validate USB 3.2 and DisplayPort 2.0 margins separately because equalization behavior can differ by protocol and lane configuration.
Use the manufacturer reference layout and configuration procedure for the 40-pin RNQ package, including bypass placement, exposed-pad treatment, high-speed routing, and return-path continuity. The redriver can compensate for deterministic channel loss, but it cannot correct a split reference plane, an impedance discontinuity, or an improperly terminated differential pair. Measure eye quality and equalization behavior at the intended 10 Gbps operating point after connector and cable effects are included.
Place the required bypass capacitors close to their designated supply pins and keep their return connections within the device ground-return structure. Follow the manufacturer supply requirements and decoupling recommendations without substituting a larger capacitor without rechecking stability and power-supply behavior. Confirm the relationship between local supply noise and the adaptive equalizer performance, since clean power helps preserve the margin required for USB 3.2 and DisplayPort 2.0 operation.
Do not treat all USB-C redrivers as interchangeable. Confirm the 40-pin RNQ footprint, every high-speed lane assignment, control pins, protocol support, and the required D_DFP configuration before replacing the TUSB1146RNQT. Also verify whether a candidate supports DisplayPort 2.0 UHBR10, two- versus four-lane operation, and USB 3.2 SSP. A matching data-rate headline alone does not establish pin-to-pin compatibility.
Thông tin tuân thủ
Compliance status was not stated in the cited product information and must be confirmed in the manufacturer product documentation before an environmental or automotive qualification decision.