TXS0108EQPWRQ1 - 8-Bit Auto-Direction Level Shifter | TI
MPN: TXS0108EQPWRQ1 ✓ Hoạt độngTXS0108EQPWRQ1 Tóm tắt
A voltage level translator (also called a logic level shifter or voltage translation IC) is an interface component in the broader logic and interface IC family that safely bridges digital devices operating at different supply domains, for example a 1.8V microcontroller talking to a 5V sensor. Level shifters protect low-voltage I/O from overvoltage while preserving logic thresholds, edge rates, and signal integrity across the voltage boundary.
Key specifications include a wide VCCA range of 1.2V to 3.6V and VCCB range of 1.65V to 5.5V, enabling translation between almost any two common logic rails. Push-pull data rates reach 110 Mbps while open-drain operation supports 2 Mbps with integrated 10 kOhm pull-up resistors. The device also offers an OE pin for 3-state operation during power sequencing and classified HBM ESD level 2 and CDM level C6 robustness per TI data.
Architecturally, the TXS0108E uses one-shot edge-rate accelerators on each channel to improve rise times, combined with a 4 kOhm series pass-gate element; this open-drain-friendly structure means it is not recommended for applications needing high drive strength such as direct LED loads.
Typical applications include automotive infotainment and body-control module I/O translation, sensor and CAN-adjacent digital interfacing, and portable electronics bridging 1.8V/2.5V/3.3V memory or peripheral buses to 5V domains. All prices cited in this page are as of 2026-08-29.
Design tip: because of the internal pull-ups, avoid this family for signals requiring low-capacitance backplane conditions; for heavy push-pull loads choose the TXB0108 instead.
Bộ thay thế dễ dàng lắp đặt cho TXS0108EQPWRQ1 — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với TXS0108EQPWRQ1 (cùng hình factor và footprint) — khác nhau ở Translator Type, Operating Temperature, Package, Direction Control, Output Type.
TXS0108EPWR
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →TXB0108QPWRQ1
⚡ Đồng góiLiên hệ để biết giá
Xem tài liệu →TXB0108PWR
⚡ Đồng góiLiên hệ để biết giá
Xem tài liệu →NXB0108PW
⚡ Đồng gói ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
SN74LVC8T245PWR
⚡ Đồng gói ⚠️ Thông số chưa được xác minh✗ Hết hàng
$0.175 / Đơn vị
Xem tài liệu →TXS0108EQPWRQ1 Thông số kỹ thuật
| Bits / Channels | 8 bidirectional channels |
| Translator Type | Auto-direction voltage level translator (open-drain and push-pull) |
| VCCA Supply Range | 1.2 V to 3.6 V |
| VCCB Supply Range | 1.65 V to 5.5 V |
| Max Data Rate (Push-Pull) | 110 Mbps |
| Max Data Rate (Open-Drain) | 2 Mbps |
| Direction Control | Not required (auto-direction sensing) |
| Kiểu đầu ra | 3-state with OE pin |
| Hộp | TSSOP-20 (PW) |
| Kiểu lắp đặt | Surface Mount |
| Nhiệt độ hoạt động | -40C to +125C (AEC-Q100 grade 1) |
| Automotive Qualification | AEC-Q100 qualified |
| ESD HBM Classification | Level 2 |
| ESD CDM Classification | Level C6 |
| Trạng thái RoHS | Compliant |
Cấu hình chân TXS0108EQPWRQ1
| Chân 1 | A1 — A-side data 1 |
| Chân 2 | A2 — A-side data 2 |
| Chân 3 | A3 — A-side data 3 |
| Chân 4 | A4 — A-side data 4 |
| Chân 5 | GND — Ground |
| Chân 6 | A5 — A-side data 5 |
| Chân 7 | A6 — A-side data 6 |
| Chân 8 | A7 — A-side data 7 |
| Chân 9 | A8 — A-side data 8 |
| Chân 10 | NC — No connect |
| Chân 11 | B8 — B-side data 8 |
| Chân 12 | B7 — B-side data 7 |
| Chân 13 | B6 — B-side data 6 |
| Chân 14 | B5 — B-side data 5 |
| Chân 16 | B4 — B-side data 4 |
| Chân 17 | B3 — B-side data 3 |
| Chân 18 | B2 — B-side data 2 |
| Chân 19 | B1 — B-side data 1 |
| Chân 20 | OE — Output enable; low = 3-state all I/O |
Ứng dụng tiêu biểu
TXS0108EQPWRQ1 phù hợp cho 6 Áp dụngs: Automotive Body Control Module I/O, I2C / Open-Drain Bus Level Shifting, Infotainment and Display Digital Interfaces, Portable / Battery-Powered Electronics, Industrial Sensor and Logic Interfacing, Networking and Communication Equipment.
Automotive Body Control Module I/O
The TXS0108EQPWRQ1 is AEC-Q100 grade 1 qualified (-40C to +125C) with HBM ESD level 2 and CDM C6 classification, making it well suited for automotive BCM signal translation between low-voltage MCUs and 5V sensor or actuator logic. Its auto-direction sensing removes firmware overhead for bidirectional lines, and the OE pin safely isolates I/O during power sequencing. Placed between a 3.3V MCU bank and a 5V chassis-logic domain, all eight channels translate independently at push-pull rates up to 110 Mbps.
Được đề xuất
I2C / Open-Drain Bus Level Shifting
The integrated 10 kOhm pull-up resistors and open-drain-tolerant architecture allow the TXS0108E to shift I2C and similar open-drain buses between 1.8V/3.3V and 5V domains at up to 2 Mbps, covering I2C standard and fast modes. Because each channel is auto-directional, SDA re-configuration happens without a direction pin. Designers should verify bus capacitance, since the 10 kOhm pull-ups limit fast-mode-plus performance on heavy loads; lower-value external pull-ups at the B-side can restore edge rates.
Được đề xuất
Infotainment and Display Digital Interfaces
In automotive infotainment head units and cluster displays, low-voltage SoCs (1.8V or 2.5V I/O) must communicate with 3.3V/5V peripherals such as touch controllers, EEPROM, and backlight control logic. The TXS0108EQPWRQ1 bridges these domains on eight channels with 110 Mbps push-pull capability, sufficient for SPI and parallel control buses. The TSSOP-20 package simplifies routing on dense boards, and AEC-Q100 grade 1 qualification supports the elevated cabin temperature environment.
Được đề xuất
Portable / Battery-Powered Electronics
Battery-powered designs commonly mix 1.8V flash/memory or SoC I/O with 3.3V or 5V peripherals. The TXS0108EQPWRQ1 accepts VCCA as low as 1.2V, accommodating exhausted-battery low-voltage rails, while translating cleanly to 5V domains. Its 3-state OE control lets a system manager float all eight lines during standby, minimizing leakage. Auto-direction operation saves microcontroller GPIO pins otherwise consumed by direction control on partially bidirectional buses.
Được đề xuất
Industrial Sensor and Logic Interfacing
Industrial control boards frequently pair 3.3V microcontrollers with legacy 5V sensor and logic subsystems. The TXS0108EQPWRQ1 translates eight such signals with automatic direction detection, easing migration of 5V-centric designs to modern MCUs. Push-pull rates up to 110 Mbps cover SPI, UART, and parallel handshake buses. Designers should avoid using it on lines that must sink heavy loads, since its 4 kOhm series element and pull-ups limit output drive strength.
Được đề xuất
Networking and Communication Equipment
Routers, switches, and line cards use the TXS0108EQPWRQ1 to bridge 1.8V PHY or ASIC management I/O to 3.3V/5V EEPROM, LED drivers, and supervisory logic. The 110 Mbps push-pull rating supports MDIO at high clock rates and other management buses, while auto-direction handling suits shared read/write lines. The OE pin supports clean bring-up sequencing when management rails power in different orders across a backplane.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho TXS0108EQPWRQ1 — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | TXS0108EPWR | TXB0108QPWRQ1 | NXB0108PW | 74LVC8T245PW |
|---|---|---|---|---|---|
| Package | TSSOP-20 (PW) | TSSOP-20 (PW) - same | TSSOP-20 (PW) - same | TSSOP-20 (PW) - same | TSSOP-20 (PW) - same |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | NXP Semiconductors | NXP Semiconductors |
| Bits / Channels | 8 bidirectional | 8 bidirectional | 8 bidirectional | 8 bidirectional | 8 bidirectional (DIR-controlled) |
| Open-Drain Support (Internal Pull-Ups) | Yes (10 kOhm) | Yes (10 kOhm) | No | No | No |
| Direction Control | None (auto-direction) | None (auto-direction) | None (auto-direction) | None (auto-direction) | DIR pins required |
Bảo phân biệt quan trọng
- Open-drain capable with integrated 10 kOhm pull-ups (vsTXB0108QPWRQ1)
- Automotive AEC-Q100 grade 1 qualification (vsTXS0108EPWR)
- Auto-direction, no DIR pins (vs74LVC8T245PW)
Ghi chú thiết kế
Power VCCA first or simultaneously with VCCB; hold OE low until both supplies are valid so all I/O stay in 3-state during sequencing. The datasheet allows any power-up order but the OE control prevents mid-ramp glitching into the 5V domain. Decouple VCCA and VCCB with 0.1 uF ceramic capacitors placed within 2 mm of the pins.
Do not use the TXS0108E on lines that must sink heavy loads (LEDs, relays): the internal 10 kOhm pull-ups and ~4 kOhm series pass element provide only weak drive. Also avoid weak external pull-ups below the internal 10 kOhm threshold interfering with auto-direction edge detection; keep bus capacitance low on open-drain channels to meet the 2 Mbps limit.
Keep traces short and reference a solid ground plane; the one-shot edge accelerators sharpen rise edges, so long stubs can cause reflections on 100 Mbps-class signals. Unused channels should have both A and B sides tied to ground or left floating per the datasheet recommendation, and APU/VCC pins must not be left unconnected on variants that expose them.
Thông tin tuân thủ
AEC-Q100 qualified grade 1 per TI product data. RoHS/lead-free per standard TI automotive production. REACH and conflict-minerals declarations available from TI material certification page.
