USB2SERA10CFK - USB 2.0 to UART Bridge | NXP | 5x5 QFN
MPN: USB2SERA10CFK ✗ Cuối đờiUSB2SERA10CFK Tóm tắt
A USB-to-UART bridge is an interface-controller IC that translates commands and data between a USB host and a conventional asynchronous serial peripheral. Within the product hierarchy, the USB2SERA10CFK belongs to the USB bridge, USB interface controller, interface IC, and semiconductor categories. Its purpose is to reduce external component count while giving an embedded product access to USB connectivity for configuration, data transfer, firmware access, or field-service connections.
The controller supports eight-bit UART data, one or two stop bits, and odd, even, or no parity. Flow-control choices include hardware flow control and Xon-Xoff software flow control. A RESUME output requests a remote wake-up, while a SUSPEND output indicates the bridge's suspended operating state. These features allow the serial side to be adapted to host timing, transceiver requirements, and legacy peripheral behavior without implementing a complete USB protocol stack in the host application.
USB2SERA10CFK is suitable for industrial control equipment, test and measurement instruments, data-acquisition equipment, configuration ports, and service interfaces. It is particularly useful where an existing TTL RS232 or RS485 design must gain USB without using a larger external bridge module. System designers should account for the electrical interface between the UART and RS232 or RS485 transceivers; the bridge itself operates at the TTL UART level.
Layout quality directly affects USB signal integrity because full-speed USB carries differential data on a compact, high-speed-capable PCB. Place the USB input-capacitance protection and required bypass components near their associated pins, provide a continuous ground reference, route D+ and D+ as a short matched pair, and avoid placing test pads or unrelated routing beneath the differential pair. The manufacturer's pin-description table should be used directly when assigning all 24 package terminals and the exposed thermal pad.
This product page consolidates the interface capabilities, package information, application guidance, and engineering constraints of the USB2SERA10CFK. It also distinguishes documented USB and UART functions from details that require confirmation from the manufacturer datasheet or a schematic review before production release.
Bộ thay thế dễ dàng lắp đặt cho USB2SERA10CFK — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Không có bộ thay thế dễ dàng lắp đặt sẵn có cho sản phẩm này.
Yêu cầu các bộ thay thếUSB2SERA10CFK Thông số kỹ thuật
| Device Type | USB 2.0 to UART bridge controller |
| USB Interface | USB 2.0 full-speed |
| Maximum USB Data Rate | 12 Mbps |
| UART Channels | 1 channel |
| Supported UART Electrical Modes | TTL RS232 or RS485 |
| Programmable Baud Rate Range | 300 bps to 1,152,000 bps |
| UART Data Length | 8 bit |
| UART Stop Bit Options | 1 or 2 stop bits |
| UART Parity Options | Odd, even, or no parity |
| Flow Control | Hardware flow control or Xon-Xoff software flow control |
| Remote Wake-Up Support | RESUME signal |
| Suspend Signal | SUSPEND output |
| Hộp | 24-HVQFN, 5 x 5 mm |
| Exposed Pad | Yes |
| Lead-Free Status | Lead-free |
| Trạng thái RoHS | RoHS compliant |
| Kiểu lắp đặt | Surface mount |
Hướng dẫn cấu hình chân USB2SERA10CFK 24-hvqfn, 5 x 5 mm
Cấu hình chân cho USB2SERA10CFK (24-hvqfn, 5 x 5 mm gói). Số thứ tự chân, chức năng và sơ đồ kết nối được xác định trong tài liệu thông số kỹ thuật của nhà sản xuất. Tham khảo nó để biết footprint và hướng dẫn hàn chính xác.
Không có dữ liệu chân cụ thể sẵn có cho USB2SERA10CFK.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
USB2SERA10CFK phù hợp cho 6 Áp dụngs: Industrial Control Configuration Port, USB-to-RS485 Data Acquisition, Test and Measurement Instrument Interface, Firmware Update and Service Connectivity, Point-of-Sale and Peripheral Connectivity, Remote Monitoring and Telemetry Link.
Industrial Control Configuration Port
USB2SERA10CFK is suitable for adding a service and configuration port to an industrial controller that already uses a TTL UART. Its USB 2.0 full-speed interface operates at up to 12 Mbps, while the UART side supports 300 bps to 1,152,000 bps for command exchange, parameter updates, and diagnostic logs. Hardware flow control can regulate traffic when the embedded target cannot accept data continuously, while Xon-Xoff provides an alternative for simpler links. The compact 24-HVQFN package helps minimize board area, although a separate transceiver may be required when the external interface is physically RS485.
Được đề xuất
USB-to-RS485 Data Acquisition
USB2SERA10CFK fits a data-acquisition product that needs to expose a legacy TTL serial controller through USB and then connect that controller to an RS485 network. The bridge's full-speed USB path can carry substantially more data than required by many 300 bps to 115,200 bps legacy instruments. An external RS485 transceiver is needed to create the physical differential bus, and its direction control, receiver enable, biasing, termination, and isolation requirements must be integrated with the bridge's UART and flow-control resources.
Được đề xuất
Test and Measurement Instrument Interface
USB2SERA10CFK can provide a PC-connected control channel for test and measurement equipment with an embedded TTL UART. Its one-channel architecture keeps the design focused on command, status, and measurement-result transfer, while programmable baud rates support legacy instruments operating at common low-speed rates. The USB 2.0 full-speed link provides a 12 Mbps ceiling, and the bridge supports both hardware and Xon-Xoff flow control for hosts that need to avoid buffer overflow. Designers should keep the USB differential pair away from analog and high-impedance measurement circuitry.
Được đề xuất
Firmware Update and Service Connectivity
USB2SERA10CFK provides a practical service path for firmware updates and field diagnostics in an embedded product with an accessible internal UART. The host can transfer a firmware image through the USB 2.0 full-speed interface while the bridge translates it into serial traffic for the target controller. Xon-Xoff can coordinate a simple firmware receiver, or hardware flow control can be used where the target implements request-to-send and clear-to-send signaling. The service connector should include practical ESD and overvoltage protection because external ports are frequent points of electrical stress.
Được đề xuất
Point-of-Sale and Peripheral Connectivity
USB2SERA10CFK can bridge a legacy serial peripheral to a modern USB-capable host, making it useful in point-of-sale equipment, access terminals, and compact peripheral controllers. Its 12 Mbps USB full-speed rate comfortably exceeds the throughput of conventional low-speed UART links, and programmable serial framing supports different peripheral conventions. When the attached product uses RS232 levels rather than TTL, an appropriate level translator or transceiver is necessary. The complete interface should be checked for automatic configuration, signal polarity, and reset behavior before it is used with a specific peripheral.
Được đề xuất
Remote Monitoring and Telemetry Link
USB2SERA10CFK is appropriate for monitoring equipment that collects status information from a remote or distributed embedded node over a serial link. The bridge's selectable baud rate, parity, and stop-bit settings support compatibility with existing telemetry hardware, while hardware flow control can prevent buffer overrun during bursts. For RS485 deployments, the bridge must be paired with a transceiver and the bus layout should include appropriate termination and protection. USB enumeration and suspend or resume signals should also be incorporated into the host application's monitoring and recovery behavior.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho USB2SERA10CFK — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này |
|---|---|
| Package | 24-HVQFN, 5 x 5 mm |
| Brand | NXP Semiconductors |
| Device Function | USB-to-UART bridge controller |
| USB Specification | USB 2.0 full-speed |
| Maximum USB Data Rate | 12 Mbps |
| UART Channels | 1 channel |
| Supported Serial Modes | TTL RS232 or RS485 |
| Programmable Baud Rate Range | 300 bps to 1,152,000 bps |
| UART Data Configuration | 8 bit; 1 or 2 stop bits; odd, even, or no parity |
| Flow Control | Hardware flow control or Xon-Xoff software flow control |
| Power Management | RESUME remote wake-up and SUSPEND output |
| RoHS Status | RoHS compliant |
Bảo phân biệt quan trọng
- Combines USB 2.0 full-speed and configurable serial framing in one 5 x 5 mm device (vsGeneric USB-to-UART bridge modules)
- Supports both hardware and software flow-control methods (vsBasic UART bridges)
- Integrates suspend and remote wake-up signaling (vsSimple data-only USB-UART adapters)
- Supports legacy TTL RS232 or RS485-oriented interfaces (vsUSB-only interface controllers)
Ghi chú thiết kế
Route the USB D+ and D− conductors as a short differential pair over a continuous ground reference. Place USB input-capacitance protection and required bypass capacitors near the associated USB2SERA10CFK terminals, and keep the pair away from switching-regulator nodes and unrelated high-speed traces. Check the complete return-current path beneath the pair because interruptions in the ground plane can increase radiated emissions and reduce immunity.
Treat the exposed pad as both a thermal and electrical land. Follow the manufacturer land pattern and exposed-pad connection instructions, place thermal vias where the package pattern permits, and maintain uninterrupted ground copper beneath the device. Do not estimate thermal performance from exposed-pad area alone; use the package thermal data and the final board stack-up when checking junction temperature under sustained USB activity.
Do not treat the TTL UART outputs as physical RS232 or RS485 line drivers. USB2SERA10CFK supports interfaces intended for TTL RS232 or RS485 transceiver use, so the design may still require level translation, differential drive, receiver enable logic, bias resistors, termination, and isolation. Confusing logic-level UART with an RS232 connector can cause incompatible voltage ranges and damage to the attached equipment.
Decouple each required power rail close to its USB2SERA10CFK terminal and confirm the device's voltage limits, current demand, and clock source against the manufacturer datasheet before schematic release. Separate USB input-capacitance protection from sensitive analog sections of the host board. If an RS485 transceiver is added, budget its supply current and enable timing alongside the bridge rather than sizing the rail from the bridge alone.
Confirm baud rate, parity, stop bits, and flow-control mode on both the USB host and embedded target. A matching baud rate alone does not prevent framing errors when parity or stop-bit settings differ. For Xon-Xoff links, verify that the embedded firmware reserves the correct control-character values; for hardware flow control, verify that request-to-send and clear-to-send are wired and managed correctly.
Thông tin tuân thủ
RoHS-compliant and lead-free status are identified for USB2SERA10CFK. REACH, halogen-free, and conflict-minerals declarations are not stated.