NXP Semiconductors

USB2SERA10CFK - USB 2.0 to UART Bridge | NXP | 5x5 QFN

MPN: USB2SERA10CFK ✗ 停產
24-HVQFN, 5 x 5 mm Package
MOQ: 1 |

USB2SERA10CFK 概覽

NXP Semiconductors USB2SERA10CFK is a single-chip USB-to-UART bridge controller that adds a USB 2.0 full-speed serial interface to an embedded system. It operates at 12 Mbps, supports a TTL RS232 or RS485 UART, and provides programmable baud rates from 300 bps to 1,152,000 bps. The device is packaged in a 24-pin HVQFN package measuring 5 x 5 mm.

A USB-to-UART bridge is an interface-controller IC that translates commands and data between a USB host and a conventional asynchronous serial peripheral. Within the product hierarchy, the USB2SERA10CFK belongs to the USB bridge, USB interface controller, interface IC, and semiconductor categories. Its purpose is to reduce external component count while giving an embedded product access to USB connectivity for configuration, data transfer, firmware access, or field-service connections.

The controller supports eight-bit UART data, one or two stop bits, and odd, even, or no parity. Flow-control choices include hardware flow control and Xon-Xoff software flow control. A RESUME output requests a remote wake-up, while a SUSPEND output indicates the bridge's suspended operating state. These features allow the serial side to be adapted to host timing, transceiver requirements, and legacy peripheral behavior without implementing a complete USB protocol stack in the host application.

USB2SERA10CFK is suitable for industrial control equipment, test and measurement instruments, data-acquisition equipment, configuration ports, and service interfaces. It is particularly useful where an existing TTL RS232 or RS485 design must gain USB without using a larger external bridge module. System designers should account for the electrical interface between the UART and RS232 or RS485 transceivers; the bridge itself operates at the TTL UART level.

Layout quality directly affects USB signal integrity because full-speed USB carries differential data on a compact, high-speed-capable PCB. Place the USB input-capacitance protection and required bypass components near their associated pins, provide a continuous ground reference, route D+ and D+ as a short matched pair, and avoid placing test pads or unrelated routing beneath the differential pair. The manufacturer's pin-description table should be used directly when assigning all 24 package terminals and the exposed thermal pad.

This product page consolidates the interface capabilities, package information, application guidance, and engineering constraints of the USB2SERA10CFK. It also distinguishes documented USB and UART functions from details that require confirmation from the manufacturer datasheet or a schematic review before production release.

直接替換替代品,適用於 USB2SERA10CFK — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。

此產品無可直接替換的替代品。

申請替代品

USB2SERA10CFK 規格

Device Type USB 2.0 to UART bridge controller
USB Interface USB 2.0 full-speed
Maximum USB Data Rate 12 Mbps
UART Channels 1 channel
Supported UART Electrical Modes TTL RS232 or RS485
Programmable Baud Rate Range 300 bps to 1,152,000 bps
UART Data Length 8 bit
UART Stop Bit Options 1 or 2 stop bits
UART Parity Options Odd, even, or no parity
Flow Control Hardware flow control or Xon-Xoff software flow control
Remote Wake-Up Support RESUME signal
Suspend Signal SUSPEND output
封裝 24-HVQFN, 5 x 5 mm
Exposed Pad Yes
Lead-Free Status Lead-free
RoHS 狀態 RoHS compliant
安裝類型 Surface mount

USB2SERA10CFK 24-hvqfn, 5 x 5 mm 腳位配置指南

USB2SERA10CFK(24-hvqfn, 5 x 5 mm 封裝)的腳位配置。 腳位編號、功能與連接圖定義於製造商資料手冊中。請參閱該手冊以取得確切的封裝尺寸與焊接指引。

USB2SERA10CFK 的 24-hvqfn, 5 x 5 mm 封裝腳位圖

無詳細腳位定義資料: USB2SERA10CFK.

請參閱 資料表 以查看完整腳位配置。

典型應用

USB2SERA10CFK 適用於 6 應用s: Industrial Control Configuration Port, USB-to-RS485 Data Acquisition, Test and Measurement Instrument Interface, Firmware Update and Service Connectivity, Point-of-Sale and Peripheral Connectivity, Remote Monitoring and Telemetry Link.

🏭

Industrial Control Configuration Port

USB2SERA10CFK is suitable for adding a service and configuration port to an industrial controller that already uses a TTL UART. Its USB 2.0 full-speed interface operates at up to 12 Mbps, while the UART side supports 300 bps to 1,152,000 bps for command exchange, parameter updates, and diagnostic logs. Hardware flow control can regulate traffic when the embedded target cannot accept data continuously, while Xon-Xoff provides an alternative for simpler links. The compact 24-HVQFN package helps minimize board area, although a separate transceiver may be required when the external interface is physically RS485.

🖥️

USB-to-RS485 Data Acquisition

USB2SERA10CFK fits a data-acquisition product that needs to expose a legacy TTL serial controller through USB and then connect that controller to an RS485 network. The bridge's full-speed USB path can carry substantially more data than required by many 300 bps to 115,200 bps legacy instruments. An external RS485 transceiver is needed to create the physical differential bus, and its direction control, receiver enable, biasing, termination, and isolation requirements must be integrated with the bridge's UART and flow-control resources.

🔧

Test and Measurement Instrument Interface

USB2SERA10CFK can provide a PC-connected control channel for test and measurement equipment with an embedded TTL UART. Its one-channel architecture keeps the design focused on command, status, and measurement-result transfer, while programmable baud rates support legacy instruments operating at common low-speed rates. The USB 2.0 full-speed link provides a 12 Mbps ceiling, and the bridge supports both hardware and Xon-Xoff flow control for hosts that need to avoid buffer overflow. Designers should keep the USB differential pair away from analog and high-impedance measurement circuitry.

📱

Firmware Update and Service Connectivity

USB2SERA10CFK provides a practical service path for firmware updates and field diagnostics in an embedded product with an accessible internal UART. The host can transfer a firmware image through the USB 2.0 full-speed interface while the bridge translates it into serial traffic for the target controller. Xon-Xoff can coordinate a simple firmware receiver, or hardware flow control can be used where the target implements request-to-send and clear-to-send signaling. The service connector should include practical ESD and overvoltage protection because external ports are frequent points of electrical stress.

🖥️

Point-of-Sale and Peripheral Connectivity

USB2SERA10CFK can bridge a legacy serial peripheral to a modern USB-capable host, making it useful in point-of-sale equipment, access terminals, and compact peripheral controllers. Its 12 Mbps USB full-speed rate comfortably exceeds the throughput of conventional low-speed UART links, and programmable serial framing supports different peripheral conventions. When the attached product uses RS232 levels rather than TTL, an appropriate level translator or transceiver is necessary. The complete interface should be checked for automatic configuration, signal polarity, and reset behavior before it is used with a specific peripheral.

🌐

Remote Monitoring and Telemetry Link

USB2SERA10CFK is appropriate for monitoring equipment that collects status information from a remote or distributed embedded node over a serial link. The bridge's selectable baud rate, parity, and stop-bit settings support compatibility with existing telemetry hardware, while hardware flow control can prevent buffer overrun during bursts. For RS485 deployments, the bridge must be paired with a transceiver and the bus layout should include appropriate termination and protection. USB enumeration and suspend or resume signals should also be incorporated into the host application's monitoring and recovery behavior.

What is the USB2SERA10CFK?
The USB2SERA10CFK is an NXP single-chip USB-to-UART bridge controller for USB 2.0 full-speed systems. It transfers data between a USB host and a TTL RS232 or RS485 UART at up to 12 Mbps. The bridge supports programmable baud rates from 300 bps to 1,152,000 bps, eight-bit data, one or two stop bits, and odd, even, or no parity. It is packaged in a 24-HVQFN package measuring 5 x 5 mm.
Where can I download the USB2SERA10CFK datasheet PDF?
The USB2SERA10CFK datasheet can be accessed through the NXP document listing linked from the product documentation resources. The manufacturer datasheet is the authoritative source for the 24-terminal pin description, clock requirements, electrical limits, and recommended application circuit. The accessible NXP datasheet mirror also identifies the device as a USB 2.0 full-speed, 12 Mbps USB-to-UART bridge supporting TTL RS232 and RS485.
Where can I find the USB2SERA10CFK pinout?
The USB2SERA10CFK pinout is defined by the pin-description table in the manufacturer datasheet. The device uses a 24-HVQFN package with an exposed pad, so the exposed thermal pad and its required connection must be treated as a distinct physical feature during layout. Use the manufacturer's terminal numbering rather than inferring assignments from a similar QFN device, and verify every UART, USB, clock, power, and control connection before fabrication.
What are the key specifications of USB2SERA10CFK that engineers should know?
The key USB2SERA10CFK specifications are USB 2.0 full-speed operation, a maximum USB data rate of 12 Mbps, one UART channel, and support for TTL RS232 or RS485. Serial rates are programmable from 300 bps to 1,152,000 bps. Data framing supports eight bits with one or two stop bits and odd, even, or no parity. Flow control can use hardware signaling or Xon-Xoff, and the package is a 24-HVQFN measuring 5 x 5 mm.
Can USB2SERA10CFK communicate with an RS485 device?
Yes, USB2SERA10CFK supports an RS485-oriented UART interface at the TTL side of the circuit. A suitable RS485 transceiver is still required between the bridge and the physical bus because the bridge does not directly drive the differential RS485 cable. System designers must also determine whether the application requires hardware flow control, software flow control, termination, biasing, isolation, or a separate transceiver sleep-control arrangement.
What baud rates and parity formats does USB2SERA10CFK support?
USB2SERA10CFK supports programmable custom baud rates from 300 bps to 1,152,000 bps. Each UART character can contain eight data bits, with configurable one- or two-stop-bit framing and odd, even, or no parity. These settings should match the connected UART peripheral exactly. If the USB host and embedded device disagree about baud rate, parity, stop bits, or flow control, data may be corrupted even when the USB link itself is operating normally.
Does USB2SERA10CFK support hardware flow control and Xon-Xoff?
Yes, USB2SERA10CFK supports both hardware flow control and software flow control using Xon-Xoff. Hardware flow control is appropriate when the connected design provides dedicated request-to-send and clear-to-send signaling. Xon-Xoff can serve simpler point-to-point links where in-band control characters are acceptable. The choice affects firmware, driver behavior, and the UART connection, so it should be fixed before the PCB interface is finalized.
How does USB2SERA10CFK handle suspend and remote wake-up?
USB2SERA10CFK provides a SUSPEND output and a RESUME signal for coordinated power management. SUSPEND indicates that the USB operating state has changed, while RESUME can request a remote wake-up. These functions help a host application and the embedded peripheral coordinate sleep behavior without continuous data transfers. The exact timing and polarity requirements should be taken from the manufacturer timing diagrams before implementing a power-management handshake.
What is the best drop-in replacement for USB2SERA10CFK?
No drop-in replacement can be identified as a confirmed equivalent from the available cross-reference results. A valid replacement would need the same 24-HVQFN footprint, pin-to-pin terminal assignments, USB device and power requirements, UART framing behavior, flow-control implementation, clock arrangement, and 5 x 5 mm land pattern. Do not substitute a USB-UART IC solely because it uses USB 2.0 and supports similar baud rates; verify the complete pin description and application circuit first.
Can another USB-to-UART bridge replace USB2SERA10CFK?
A different USB-to-UART bridge can replace USB2SERA10CFK only after confirming mechanical, electrical, and behavioral compatibility. The candidate must use the same 24-HVQFN land pattern and preserve the UART and USB pin assignments, or the PCB must be redesigned. Its operating voltage, clock source, suspend behavior, flow-control pins, UART logic levels, and supported RS485 interface must also match the existing design.
USB2SERA10CFK vs FT232R-style bridges - which should I choose?
USB2SERA10CFK is the better fit when an existing design specifically targets its 24-HVQFN footprint and NXP UART behavior. A FT232R-style bridge is not a pin-compatible drop-in choice because the packages, terminal assignments, power requirements, and interface organization differ. The practical comparison is therefore between redesign effort and device features rather than between identical packages, and the target MPN should be chosen when avoiding an existing board redesign is the priority.
When should I choose USB2SERA10CFK over another USB serial controller?
Choose USB2SERA10CFK when the product already accommodates its 24-HVQFN, 5 x 5 mm footprint and needs one USB-to-UART channel with configurable serial framing, hardware or software flow control, and suspend or resume signaling. Choose another controller when its package, supply architecture, driver ecosystem, baud-rate range, transceiver interface, or certification requirements provide a stronger system-level advantage. The choice should follow the complete interface requirements rather than USB data rate alone.
Is USB2SERA10CFK suitable for industrial control equipment?
USB2SERA10CFK is suitable for industrial control and service interfaces that need a compact USB 2.0 full-speed connection to a TTL UART. Its 12 Mbps USB rate and 300 bps to 1,152,000 bps UART range cover configuration, monitoring, and moderate-rate data-transfer tasks. For harsh installations, add the required transceiver, surge protection, isolation, grounding, and enclosure-level interface protection rather than treating the USB connector as an industrial surge path.
Where to buy USB2SERA10CFK online?
Use the Request a Quote form on this page to ask about USB2SERA10CFK availability, current lead time, minimum order quantity, and the exact package and shipping configuration. The product listing identifies the part as an NXP 24-HVQFN USB-to-UART bridge. Before ordering, confirm the suffix CFK, reel or tray orientation, quantity, and any required assembly or traceability requirements with the supplier.
What is the price of USB2SERA10CFK?
Submit the USB2SERA10CFK requirements through the Request a Quote form on this page for a current quotation. The form is the appropriate commercial channel for unit pricing, quantity breaks, currency, and stock allocation because pricing changes with quantity, packaging, market conditions, and delivery requirements. Include the exact MPN USB2SERA10CFK, desired quantity, and shipping destination in the request.
What is the lead time for USB2SERA10CFK?
Request the current USB2SERA10CFK lead time through the Request a Quote form on this page. Lead time can vary with manufacturer inventory, order volume, package configuration, and incoming manufacturing schedules. A one-piece evaluation requirement should be stated separately from a production quantity so the supplier can distinguish available stock from scheduled replenishment and provide a delivery commitment for the specific order.
Is USB2SERA10CFK in stock?
Current USB2SERA10CFK stock status should be confirmed through the Request a Quote form on this page. Include the required quantity, date code preference, packaging format, and destination so the response reflects an actionable allocation rather than a generic availability statement. The 24-HVQFN package and exposed pad should also be confirmed as part of the order to avoid a package-interpretation mismatch.
Is USB2SERA10CFK RoHS compliant and lead-free?
USB2SERA10CFK is identified as RoHS compliant and lead-free. The package description also identifies a lead-free 24-HVQFN construction with an exposed pad. These declarations address hazardous-substance and lead-finishing requirements for the device, but they do not establish the compliance status of the assembled product. A production assembly should also evaluate its selected PCB, connectors, enclosure, and other purchased components.
How should USB2SERA10CFK be laid out for USB signal integrity?
Route the USB2SERA10CFK D+ and D− conductors as a short, tightly coupled differential pair on a continuous ground plane. Keep the pair away from switching nodes, high-current return paths, and unrelated digital routing, and place the required USB input-capacitance protection and bypass components close to their relevant pins. The exposed pad requires careful thermal-via and copper treatment, while avoiding voids that could interfere with high-speed return-current continuity.

工程參考資料,適用於 USB2SERA10CFK — 比較、設計指引及合規資訊。

選型指南

Choose USB2SERA10CFK when the PCB already uses, or can be designed around, the 24-HVQFN 5 x 5 mm footprint and the product needs a single USB 2.0 full-speed connection to a TTL RS232 or RS485-oriented UART. Its programmable baud rates, selectable framing, hardware and Xon-Xoff flow control, and suspend or resume signaling are useful for industrial controllers, service ports, test instruments, and legacy peripherals. A different USB-to-UART controller should be considered when a smaller package, integrated transceiver, different supply architecture, broader channel count, or established host-driver ecosystem offers a stronger system benefit. No confirmed drop-in substitute has been established for this exact package and terminal arrangement, so a redesign should be treated as a new board-level integration rather than a simple component substitution.

與替代品比較

參數 本產品
Package 24-HVQFN, 5 x 5 mm
Brand NXP Semiconductors
Device Function USB-to-UART bridge controller
USB Specification USB 2.0 full-speed
Maximum USB Data Rate 12 Mbps
UART Channels 1 channel
Supported Serial Modes TTL RS232 or RS485
Programmable Baud Rate Range 300 bps to 1,152,000 bps
UART Data Configuration 8 bit; 1 or 2 stop bits; odd, even, or no parity
Flow Control Hardware flow control or Xon-Xoff software flow control
Power Management RESUME remote wake-up and SUSPEND output
RoHS Status RoHS compliant

主要差異化特點

  • Combines USB 2.0 full-speed and configurable serial framing in one 5 x 5 mm device (對比Generic USB-to-UART bridge modules)
  • Supports both hardware and software flow-control methods (對比Basic UART bridges)
  • Integrates suspend and remote wake-up signaling (對比Simple data-only USB-UART adapters)
  • Supports legacy TTL RS232 or RS485-oriented interfaces (對比USB-only interface controllers)

設計說明

Route the USB D+ and D− conductors as a short differential pair over a continuous ground reference. Place USB input-capacitance protection and required bypass capacitors near the associated USB2SERA10CFK terminals, and keep the pair away from switching-regulator nodes and unrelated high-speed traces. Check the complete return-current path beneath the pair because interruptions in the ground plane can increase radiated emissions and reduce immunity.

Treat the exposed pad as both a thermal and electrical land. Follow the manufacturer land pattern and exposed-pad connection instructions, place thermal vias where the package pattern permits, and maintain uninterrupted ground copper beneath the device. Do not estimate thermal performance from exposed-pad area alone; use the package thermal data and the final board stack-up when checking junction temperature under sustained USB activity.

Do not treat the TTL UART outputs as physical RS232 or RS485 line drivers. USB2SERA10CFK supports interfaces intended for TTL RS232 or RS485 transceiver use, so the design may still require level translation, differential drive, receiver enable logic, bias resistors, termination, and isolation. Confusing logic-level UART with an RS232 connector can cause incompatible voltage ranges and damage to the attached equipment.

Decouple each required power rail close to its USB2SERA10CFK terminal and confirm the device's voltage limits, current demand, and clock source against the manufacturer datasheet before schematic release. Separate USB input-capacitance protection from sensitive analog sections of the host board. If an RS485 transceiver is added, budget its supply current and enable timing alongside the bridge rather than sizing the rail from the bridge alone.

Confirm baud rate, parity, stop bits, and flow-control mode on both the USB host and embedded target. A matching baud rate alone does not prevent framing errors when parity or stop-bit settings differ. For Xon-Xoff links, verify that the embedded firmware reserves the correct control-character values; for hardware flow control, verify that request-to-send and clear-to-send are wired and managed correctly.

合規資訊

RoHS
Compliant
REACH
Unknown
AEC-Q100
Not Applicable
無鉛
Yes
無鹵
Unknown
衝突礦產
Unknown

RoHS-compliant and lead-free status are identified for USB2SERA10CFK. REACH, halogen-free, and conflict-minerals declarations are not stated.

資料驗證日期: 2026-11-10 — 資料由 XAIPART 元件工程團隊驗證及整理

相關搜尋

USB2SERA10CFK datasheet USB2SERA10CFK datasheet pdf USB2SERA10CFK pinout USB2SERA10CFK 24 HVQFN USB2SERA10CFK equivalent USB2SERA10CFK replacement USB2SERA10CFK cross reference USB2SERA10CFK price USB2SERA10CFK stock NXP USB2SERA10CFK USB2SERA10CFK RS485 interface USB2SERA10CFK baud rate USB2SERA10CFK application circuit

相關元件與詞彙

NXP Semiconductors USB2SERA10CFK USB-to-UART bridge USB bridge controller USB interface controller interface IC semiconductor USB 2.0 USB full-speed 12 Mbps UART TTL RS232 RS485 baud rate 300 bps to 1,152,000 bps hardware flow control Xon-Xoff RESUME SUSPEND 24-HVQFN QFN package surface mount RoHS lead-free
快速報價 RFQ
請填寫完整詳細資料 — 我們的業務團隊將於 24 小時內回覆
料號 製造商 封裝 QTY 目標價格 小計
✓
報價已提交!

我們將於 24 小時內回覆您的電子郵件

1
詢價已提交
2
已收到報價
3
已下單
4
付款
5
已出貨
6
已送達
檢視詢價單詳情