USB2SERA10CFK - USB 2.0 to UART Bridge | NXP | 5x5 QFN
MPN: USB2SERA10CFK ✗ Akhir HayatUSB2SERA10CFK Ringkasan
A USB-to-UART bridge is an interface-controller IC that translates commands and data between a USB host and a conventional asynchronous serial peripheral. Within the product hierarchy, the USB2SERA10CFK belongs to the USB bridge, USB interface controller, interface IC, and semiconductor categories. Its purpose is to reduce external component count while giving an embedded product access to USB connectivity for configuration, data transfer, firmware access, or field-service connections.
The controller supports eight-bit UART data, one or two stop bits, and odd, even, or no parity. Flow-control choices include hardware flow control and Xon-Xoff software flow control. A RESUME output requests a remote wake-up, while a SUSPEND output indicates the bridge's suspended operating state. These features allow the serial side to be adapted to host timing, transceiver requirements, and legacy peripheral behavior without implementing a complete USB protocol stack in the host application.
USB2SERA10CFK is suitable for industrial control equipment, test and measurement instruments, data-acquisition equipment, configuration ports, and service interfaces. It is particularly useful where an existing TTL RS232 or RS485 design must gain USB without using a larger external bridge module. System designers should account for the electrical interface between the UART and RS232 or RS485 transceivers; the bridge itself operates at the TTL UART level.
Layout quality directly affects USB signal integrity because full-speed USB carries differential data on a compact, high-speed-capable PCB. Place the USB input-capacitance protection and required bypass components near their associated pins, provide a continuous ground reference, route D+ and D+ as a short matched pair, and avoid placing test pads or unrelated routing beneath the differential pair. The manufacturer's pin-description table should be used directly when assigning all 24 package terminals and the exposed thermal pad.
This product page consolidates the interface capabilities, package information, application guidance, and engineering constraints of the USB2SERA10CFK. It also distinguishes documented USB and UART functions from details that require confirmation from the manufacturer datasheet or a schematic review before production release.
Pilihan pengganti yang segera untuk USB2SERA10CFK — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.
Tiada pilihan pengganti yang segera untuk produk ini.
Minta AlternatifUSB2SERA10CFK Spesifikasi
| Device Type | USB 2.0 to UART bridge controller |
| USB Interface | USB 2.0 full-speed |
| Maximum USB Data Rate | 12 Mbps |
| UART Channels | 1 channel |
| Supported UART Electrical Modes | TTL RS232 or RS485 |
| Programmable Baud Rate Range | 300 bps to 1,152,000 bps |
| UART Data Length | 8 bit |
| UART Stop Bit Options | 1 or 2 stop bits |
| UART Parity Options | Odd, even, or no parity |
| Flow Control | Hardware flow control or Xon-Xoff software flow control |
| Remote Wake-Up Support | RESUME signal |
| Suspend Signal | SUSPEND output |
| Kemasan | 24-HVQFN, 5 x 5 mm |
| Exposed Pad | Yes |
| Lead-Free Status | Lead-free |
| Status RoHS | RoHS compliant |
| Jenis Pemasangan | Surface mount |
Panduan Konfigurasi Pin USB2SERA10CFK 24-hvqfn, 5 x 5 mm
Konfigurasi pin untuk USB2SERA10CFK (24-hvqfn, 5 x 5 mm pakai). Penomeran pin, fungsi, dan garis bentuk koneksi ditakrifkan dalam dokumen pengeluar. Rujuk dokumen untuk kebentuk dan pedoman pengasman.
Tiada data garisan pin yang diperoleh untuk USB2SERA10CFK.
Rujuk kepada lembaran data untuk konfigurasi pin penuh.
Aplikasi Biasa
USB2SERA10CFK patut untuk 6 aplikasis: Industrial Control Configuration Port, USB-to-RS485 Data Acquisition, Test and Measurement Instrument Interface, Firmware Update and Service Connectivity, Point-of-Sale and Peripheral Connectivity, Remote Monitoring and Telemetry Link.
Industrial Control Configuration Port
USB2SERA10CFK is suitable for adding a service and configuration port to an industrial controller that already uses a TTL UART. Its USB 2.0 full-speed interface operates at up to 12 Mbps, while the UART side supports 300 bps to 1,152,000 bps for command exchange, parameter updates, and diagnostic logs. Hardware flow control can regulate traffic when the embedded target cannot accept data continuously, while Xon-Xoff provides an alternative for simpler links. The compact 24-HVQFN package helps minimize board area, although a separate transceiver may be required when the external interface is physically RS485.
Disebarkan
USB-to-RS485 Data Acquisition
USB2SERA10CFK fits a data-acquisition product that needs to expose a legacy TTL serial controller through USB and then connect that controller to an RS485 network. The bridge's full-speed USB path can carry substantially more data than required by many 300 bps to 115,200 bps legacy instruments. An external RS485 transceiver is needed to create the physical differential bus, and its direction control, receiver enable, biasing, termination, and isolation requirements must be integrated with the bridge's UART and flow-control resources.
Disebarkan
Test and Measurement Instrument Interface
USB2SERA10CFK can provide a PC-connected control channel for test and measurement equipment with an embedded TTL UART. Its one-channel architecture keeps the design focused on command, status, and measurement-result transfer, while programmable baud rates support legacy instruments operating at common low-speed rates. The USB 2.0 full-speed link provides a 12 Mbps ceiling, and the bridge supports both hardware and Xon-Xoff flow control for hosts that need to avoid buffer overflow. Designers should keep the USB differential pair away from analog and high-impedance measurement circuitry.
Disebarkan
Firmware Update and Service Connectivity
USB2SERA10CFK provides a practical service path for firmware updates and field diagnostics in an embedded product with an accessible internal UART. The host can transfer a firmware image through the USB 2.0 full-speed interface while the bridge translates it into serial traffic for the target controller. Xon-Xoff can coordinate a simple firmware receiver, or hardware flow control can be used where the target implements request-to-send and clear-to-send signaling. The service connector should include practical ESD and overvoltage protection because external ports are frequent points of electrical stress.
Disebarkan
Point-of-Sale and Peripheral Connectivity
USB2SERA10CFK can bridge a legacy serial peripheral to a modern USB-capable host, making it useful in point-of-sale equipment, access terminals, and compact peripheral controllers. Its 12 Mbps USB full-speed rate comfortably exceeds the throughput of conventional low-speed UART links, and programmable serial framing supports different peripheral conventions. When the attached product uses RS232 levels rather than TTL, an appropriate level translator or transceiver is necessary. The complete interface should be checked for automatic configuration, signal polarity, and reset behavior before it is used with a specific peripheral.
Disebarkan
Remote Monitoring and Telemetry Link
USB2SERA10CFK is appropriate for monitoring equipment that collects status information from a remote or distributed embedded node over a serial link. The bridge's selectable baud rate, parity, and stop-bit settings support compatibility with existing telemetry hardware, while hardware flow control can prevent buffer overrun during bursts. For RS485 deployments, the bridge must be paired with a transceiver and the bus layout should include appropriate termination and protection. USB enumeration and suspend or resume signals should also be incorporated into the host application's monitoring and recovery behavior.
Disebarkan
Ringkasan Produk Disebarkan
Data referensi kejuruteraan untuk USB2SERA10CFK — perbandingan, panduan rancangan, dan maklumat kesediaan
Panduan Pilihan
Perbandingan dengan Gantian
| Parametr | Produk Ini |
|---|---|
| Package | 24-HVQFN, 5 x 5 mm |
| Brand | NXP Semiconductors |
| Device Function | USB-to-UART bridge controller |
| USB Specification | USB 2.0 full-speed |
| Maximum USB Data Rate | 12 Mbps |
| UART Channels | 1 channel |
| Supported Serial Modes | TTL RS232 or RS485 |
| Programmable Baud Rate Range | 300 bps to 1,152,000 bps |
| UART Data Configuration | 8 bit; 1 or 2 stop bits; odd, even, or no parity |
| Flow Control | Hardware flow control or Xon-Xoff software flow control |
| Power Management | RESUME remote wake-up and SUSPEND output |
| RoHS Status | RoHS compliant |
Penyeberangsung Jelas
- Combines USB 2.0 full-speed and configurable serial framing in one 5 x 5 mm device (vsGeneric USB-to-UART bridge modules)
- Supports both hardware and software flow-control methods (vsBasic UART bridges)
- Integrates suspend and remote wake-up signaling (vsSimple data-only USB-UART adapters)
- Supports legacy TTL RS232 or RS485-oriented interfaces (vsUSB-only interface controllers)
Catatan Desain
Route the USB D+ and D− conductors as a short differential pair over a continuous ground reference. Place USB input-capacitance protection and required bypass capacitors near the associated USB2SERA10CFK terminals, and keep the pair away from switching-regulator nodes and unrelated high-speed traces. Check the complete return-current path beneath the pair because interruptions in the ground plane can increase radiated emissions and reduce immunity.
Treat the exposed pad as both a thermal and electrical land. Follow the manufacturer land pattern and exposed-pad connection instructions, place thermal vias where the package pattern permits, and maintain uninterrupted ground copper beneath the device. Do not estimate thermal performance from exposed-pad area alone; use the package thermal data and the final board stack-up when checking junction temperature under sustained USB activity.
Do not treat the TTL UART outputs as physical RS232 or RS485 line drivers. USB2SERA10CFK supports interfaces intended for TTL RS232 or RS485 transceiver use, so the design may still require level translation, differential drive, receiver enable logic, bias resistors, termination, and isolation. Confusing logic-level UART with an RS232 connector can cause incompatible voltage ranges and damage to the attached equipment.
Decouple each required power rail close to its USB2SERA10CFK terminal and confirm the device's voltage limits, current demand, and clock source against the manufacturer datasheet before schematic release. Separate USB input-capacitance protection from sensitive analog sections of the host board. If an RS485 transceiver is added, budget its supply current and enable timing alongside the bridge rather than sizing the rail from the bridge alone.
Confirm baud rate, parity, stop bits, and flow-control mode on both the USB host and embedded target. A matching baud rate alone does not prevent framing errors when parity or stop-bit settings differ. For Xon-Xoff links, verify that the embedded firmware reserves the correct control-character values; for hardware flow control, verify that request-to-send and clear-to-send are wired and managed correctly.
Maklumat Kesediaan
RoHS-compliant and lead-free status are identified for USB2SERA10CFK. REACH, halogen-free, and conflict-minerals declarations are not stated.