WM8737CLGEFL/R - 24-Bit Stereo ADC | Cirrus Logic | Audio
MPN: WM8737CLGEFL/R ✓ Hoạt độngWM8737CLGEFL/R Tóm tắt
An audio ADC is a signal-processing semiconductor that converts left- and right-channel analog voltages into digital sample data. It belongs to the ADC hierarchy within data-converter integrated circuits, where precision, bandwidth, noise performance, clocking, and interface efficiency determine suitability for recording, communication, and consumer audio equipment.
The WM8737CLGEFL/R supports 24-bit conversion at rates up to 96 kHz and uses a serial peripheral interface for digital data transfer. Its analog and digital supply range of 1.42 V to 3.6 V supports low-voltage portable and embedded designs. The operating temperature range of -25°C to +85°C covers industrial-room conditions, while the surface-mount QFN-32 package supports compact PCB construction.
The stereo ADC architecture is intended to capture two audio channels simultaneously, making the device suitable for microphone preamplification and stereo line-level digitization. A serial interface reduces the number of data connections compared with a parallel ADC and allows the converted audio stream to be transferred efficiently to a digital signal processor, audio controller, or system-on-chip.
Typical uses include digital microphones, voice-capture equipment, audio recording modules, soundbars, speaker systems, and portable consumer electronics. Low-power operation is particularly useful in battery-powered products where every milliampere affects run time. The small 5 x 5 mm footprint also helps designers retain a compact board area while implementing two-channel conversion.
PCB implementation requires careful separation of analog and digital return paths, placement of the exposed thermal pad, and a clean supply arrangement around the converter. Use the manufacturer datasheet for the complete pin-description table, recommended application circuit, exposed-pad layout, and supported interface timing before assigning tracks.
This page combines the manufacturer-device identity, package information, commercial inquiry path, technical application guidance, and available cross-reference information to help engineers evaluate the WM8737CLGEFL/R for low-voltage stereo audio acquisition systems.
Bộ thay thế dễ dàng lắp đặt cho WM8737CLGEFL/R — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
WM8737CLGEFL
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
WM8737CLGEFL/R Tỷ lệ tối đa & tính chất điện
| ADC Resolution | 24 bit |
| Maximum Sampling Rate | 96 kHz |
| Number of ADC Channels | 2 channels |
| Data Interface | SPI serial interface |
| Analog Supply Voltage Range | 1.42 V to 3.6 V |
| Digital Supply Voltage Range | 1.42 V to 3.6 V |
| Khoảng nhiệt độ hoạt động | -25°C to +85°C |
| Hộp | 32-QFN (5 x 5 mm) |
| Kiểu lắp đặt | SMD surface mount |
| Exposed Pad | Yes, QFN-32-EP |
| Device Type | Stereo ADC with microphone preamplifier |
| Product Category | ADCs/DACs - Special Purpose |
| Supplier Packaging | Reel (TR) |
| Manufacturer | Cirrus Logic Inc. |
| Trạng thái vòng đời | Active |
| Trạng thái RoHS | Compliant |
Hướng dẫn cấu hình chân WM8737CLGEFL/R 32-qfn (5 x 5 mm)
Cấu hình chân cho WM8737CLGEFL/R (32-qfn (5 x 5 mm) gói). Thành phần số hiệu này có chân đầu vào, đầu ra và nguồn cung cấp. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết cấu hình chân bù, bù trừ và chân kích hoạt. Hoàn hảo cho điều kiện tín hiệu và mạch khuếch đại.
Không có dữ liệu chân cụ thể sẵn có cho WM8737CLGEFL/R.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
WM8737CLGEFL/R phù hợp cho 6 Áp dụngs: Stereo Digital Microphone Module, Voice-Controlled Audio Capture, Soundbar and Speaker System, Portable Audio Recorder, Communications Microphone Front End, Test and Measurement Audio Analyzer.
Stereo Digital Microphone Module
The WM8737CLGEFL/R fits a two-channel digital microphone module because it combines a 24-bit stereo ADC with microphone preamplifier functionality. Its SPI interface can transfer samples to a compact audio controller without requiring a wide parallel data bus. At sampling rates up to 96 kHz, the device supports higher-resolution capture than ordinary voice-only converters. Designers should configure the analog gain and microphone bias according to the manufacturer application circuit, then isolate the analog inputs from SPI and clock routing to preserve signal integrity.
Được đề xuất
Voice-Controlled Audio Capture
The WM8737CLGEFL/R supports voice-command and hands-free products that require consistent stereo sampling before digital filtering. Its 24-bit conversion and sampling capability up to 96 kHz provide ample resolution for speech capture, while the SPI interface suits embedded processors with limited peripheral pin counts. Low-voltage analog and digital operation from 1.42 V to 3.6 V supports compact portable equipment. Firmware must configure the converter correctly, and the PCB should provide a quiet analog return path.
Được đề xuất
Soundbar and Speaker System
A soundbar can use the WM8737CLGEFL/R to digitize left and right audio inputs before volume, mixing, and loudspeaker processing. Two 24-bit channels at rates up to 96 kHz suit consumer audio paths where the host processor performs filtering or level management. The compact 32-QFN package preserves board area in a densely populated enclosure. Layout should separate the converter's analog inputs from amplifier power stages and switching circuitry, while following the manufacturer exposed-pad and grounding recommendations.
Được đề xuất
Portable Audio Recorder
The WM8737CLGEFL/R is suitable for portable recorders that capture stereo analog inputs and store or transmit the resulting digital audio. Its low-voltage supply range supports compact battery-powered architecture, while 24-bit resolution at up to 96 kHz provides flexible operating modes for music or speech recording. An SPI connection reduces host-processor wiring and can support deterministic data transfer. Designers should select input and gain settings from the electrical characteristics, account for the microphone or line-source impedance, and keep switching regulators away from sensitive analog nodes.
Được đề xuất
Communications Microphone Front End
The WM8737CLGEFL/R can serve as the analog-to-digital front end in communications equipment requiring two simultaneous capture channels. Its microphone preamplifier function and 24-bit ADC support voice-quality acquisition, while the SPI interface connects efficiently to a communications processor. The 1.42 V to 3.6 V operating range permits integration with low-voltage digital systems. Input filtering, gain, and clocking must be designed from the manufacturer recommended circuit, and analog ground routing should minimize the pickup of switching and high-speed digital signals.
Được đề xuất
Test and Measurement Audio Analyzer
The WM8737CLGEFL/R can provide the conversion stage for compact audio measurement equipment that evaluates stereo analog signals. Its 24-bit resolution and 96 kHz maximum sampling rate support waveform capture, frequency-response checks, and sound-level analysis when combined with suitable front-end circuitry. SPI enables captured samples to be transferred to a test controller or embedded processor. Calibration of the analog path, clock accuracy, input bandwidth, and software scaling remain system-level tasks, while the PCB should minimize ground coupling under changing test signals.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho WM8737CLGEFL/R — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | WM8737CLGEFL |
|---|---|---|
| Package | 32-QFN (5 x 5 mm) | 32-QFN (5 x 5 mm) |
| Brand | Cirrus Logic | Cirrus Logic |
| ADC Resolution | 24 bit | 24 bit |
| Maximum Sampling Rate | 96 kHz | 96 kHz |
| Number of Channels | 2 ADC channels | 2 ADC channels |
| Interface | SPI | SPI |
| Supply Voltage Range | 1.42 V to 3.6 V | 1.42 V to 3.6 V |
| Operating Temperature Range | -25°C to +85°C | -25°C to +85°C |
| Microphone Preamplifier | Yes | Yes |
| Mounting Type | SMD surface mount | SMD surface mount |
Bảo phân biệt quan trọng
- Purpose-built stereo acquisition with microphone preamplification (vsWM8737CLGEFL)
- Compact 32-QFN implementation (vsWM8737CLGEFL)
- Low-voltage serial-interface ADC (vsWM8737CLGEFL)
Ghi chú thiết kế
Use the manufacturer QFN-32 land pattern and exposed-pad recommendation exactly. Place the input, output, and supply bypass capacitors close to their associated pins, and provide adequate thermal-via density beneath the exposed pad. Keep the pad connection compatible with the PCB's ground-plane strategy so that return currents do not cross sensitive microphone or analog input nodes.
Separate analog inputs from SPI data, clock, and switched-power traces. Route the microphone or line inputs as short, guarded traces over a continuous ground plane, and place input filtering close to the converter. This arrangement reduces capacitive pickup and common-impedance noise while preserving the low-voltage headroom available across the 1.42 V to 3.6 V supply range.
Do not assume that every similarly packaged audio converter is interchangeable. Confirm the microphone input, analog supply, digital supply, ground, clock, and SPI pins against the manufacturer pin-description table, then verify exposed-pad requirements and register behavior. A package drawing alone does not establish electrical compatibility or functional drop-in status.
Thông tin tuân thủ
RoHS compliance is identified for the exact ordering code. Other environmental declarations are not specified and remain unknown.